KLING FREITAG NOMOS XLC Performance Cardioid Subwoofer User Manual
- June 12, 2024
- Kling Freitag
Table of Contents
- Introduction
- Product Description
- Safety Instructions
- NOMOS XLC combined with other K&F tops.
- Stacking the Subwoofers
- Cardioid Arrays with Controller CD 44
- Fuse in the NOMOS XLC
- Connection
- Dimensions NOMOS XLC
- Measuring Diagrams
- Technical Specifications
- EC Declaration of Conformity
- Accessories
- Transportation and Storage
- Disposal
- Documents / Resources
K &F NOMOS XLC User’s Manual
Version 4.6
Released: 15.11.2017
Translation of the original instructions
Important Information, Please Read Before Use!
Introduction
Thank you for purchasing a KLING & FREITAG product. To guarantee a trouble-
free operating of the equipment and to allow your KLING & FREITAG NOMOS XLC
system to achieve its full potential read the user’s manual carefully before
use. This item is a quality accessory for the NOMOS XLC speaker system. As the
owner of a NOMOS XLC loudspeaker, you now have a versatile and highly
professional tool which, when operated properly, is a true pleasure to use.
1.1 Icons Used
This icon indicates a risk of injury or death. Not following these
instructions may result in serious health problems including potentially fatal
injuries.
This icon indicates a possibly dangerous situation. Not following these
instructions may cause minor injuries or damage.
This icon marks instructions for proper use of the described products. Not
following these instructions may cause malfunctions or damage.
1.2 About this Manual
User’s Manual K&F NOMOS XLC.
© KLING & FREITAG GmbH, 2009, all rights reserved.
All specifications regarding the features of the described products and
applicable safety guidelines provided in this manual are based on information
available at the time of publishing.
We assume no responsibility for technical specifications, dimensions, weights,
and properties.
All information in this manual is subject to change without notice.
To ensure safe operation, all persons using the speaker system must have
access to these user’s manual and all other relevant material during
installation. Don’t set up or operate the speaker system before you have
carefully read and fully understood this user’s manual. Keep the user’s manual
readily available on site at all times.
All KLING & FREITAG manuals are originally authored in German.
KLING & FREITAG spare manuals are separately available for order or can be
downloaded from our website: www.kling-freitag.de.
Contact Us:
info@kling-freitag.de
KLING & FREITAG GMBH, Wohlenbergstr. 5, D-30179 Hannover
Phone +49 511 96 99 70, fax +49 511 67 37 94 (other countries)
Product Description
2.1 Items Included
- Cardioid Bass Speaker NOMOS XLC
- (1x) User manual
2.2 Components
- Stacking grooves (8x) , adjacent: plastic glider
- Butterfly handles (8x)
- locking profile
- speaker enclosure
- front grille with acoustic foam
- rear grille with acoustic foam
- SpeakOn connector
- transport castors, 100 mm, permanently installed
- Plastic glider (8x) , adjacent: stacking grooves
2.3 System Requirements
Lab.gruppen IPD 2400or
K&F PLM+ 20k44 (SystemAmp, ProRental)
K&F PLM+ 12k44 (SystemAmp, ProRental)
with
K&F Connector Panel CP+ Terminalpanel (optional)or
K&F D200:4 (SystemAmp, InstallSound)
K&F D120:4 (SystemAmp, InstallSound)
K&F D80:4 (SystemAmp, InstallSound)or
K&F SystemRack
Safety Instructions
For commercial use as specified in this document only!
To prevent personal injury and damage, be sure to securely place or suspend
the speaker as specified in the locally applicable standards.
The information described here does not relieve the user of the duty to follow
the given safety requirements and legal regulations.
The persons in charge with putting up the speaker are responsible for safe
setup and use and must guarantee it.
In mobile and stationary installations, always use installation parts supplied
by KLING & FREITAG.
Unless otherwise stated, use KLING & FREITAG original parts only. Never use
other parts (in articular, parts not made by KLING & FREITAG).
Be sure to always visually inspect all safety-related speaker and accessory
components before use. In fixed installations, check the speaker for signs of
wear at regular intervals. If there are signs of wear, cracks, or deformation,
etc., replace the affected parts immediately.
Run the cables in a way that nobody can trip over them.
At least 2 people are necessary to carry the speaker.
Preventing Hearing Damage Keep your distance from operating speakers. Even
loudness levels of approx. 90 dB – that you subjectively judge as being low –
can lead to hearing damage.
3.1 Safety Instructions for Stacked Setups
Falling speakers pose the threat of fatal injuries to people near them!
Be sure to follow the relevant national specifications, norms, and safety
regulations.
Always make sure that a sufficient safety level is still given, even when
outside forces have an additional impact on the stacked speakers. Before
setup, carefully ascertain if there are any possible outside forces that could
result in the system falling over. (Slant of the ground / the bearing capacity
of the ground / wind / person or vehicle impact, etc.). A technical expert who
is responsible for the setup must evaluate and determine necessary measures
(including calculating the statics). If necessary, obtain expert proof of
stability.
Stacked systems may not fall over even if they are inclined by 15° in each
direction. If this requirement is not fulfilled, then it is necessary to take
steps to achieve compliance. Possible measures include strapping it to an
appropriate base structure or fastening it using safety straps. A planned tilt
of the loudspeakers ist not permissible. In calculations, the tilted setup
serves the purpose of levelling out unevenness.
With the set-up systems for which you cannot verify the structural safety
without safeguards, you must secure them to prevent sliding or tipping in
order to provide proof of this safety. To secure the system from tipping over,
use water tanks or floor bolts. Other possible measures include strapping it
to a suitable substructure or tying it using safety straps.
For outdoor and trade fair venues in which wind loads must be considered,
additional proof of stability is necessary.
Make sure that the stacking feet of subwoofers stacked on top of one another
are securely positioned in the grooves of the lower speaker.
If you place a top speaker on a NOMOS XLC you must always strap the speakers
to one another and secure them from falling over.
3.2 Protecting the Speakers / Operating Safety
NOMOS XLC speakers may only be used in combination with a K&F
SystemAmp/SystemRack.
System Requirements for Use
In general, audio signals must not be overdriven. This may be caused by mixing
consoles, equalizers, effect equipment, etc. and should be indicated on this
equipment. When a power amplifier is overloaded at the output (clipping), then
the amplifier activates a clipping warning signal. In any case, the signal
must be reduced as soon as it sounds unnaturallydistorted.
The following signals may damage the speakers:
-
permanent high-level signals with high frequency and continuous noise from feedback,
-
permanently distorted high-level signals,
-
noises, which occur when the amplifier is on while equipment is being connected, disconnected or switched on.
Do not install devices in any of the following places: -
where the devices are permanently exposed to direct sunlight.
-
where the devices are exposed to high moisture or rain.
-
where the devices are exposed to strong vibrations and dust.
-
where low air circulation (convection) prevails.
-
that have a small distance to a wall.
Damage caused by the speakers’ magnetic fields
Speakers are permanently surrounded by a magnetic field, even when they are
not connected. Therefore, during transport and placement of the speakers, it
is important to ensure that there is always approx. 1 m between the speakers
and magnetic data media and computer/video monitors.
For damage caused by
- overloading the speakers or
- using the speakers without K&F SystemAmp/SystemRack
we do not assume warranty and excludes liability for possible consequential damage.
NOMOS XLC combined with other K&F tops.
The NOMOS XLC can be combined with K&F top speakers using the controller K&F CD 44.
- To do so, select the desired LS blocks for the top in the Controller CD 44 or systemamp
TOPAS, and combine these with the desired LS block for the NOMOS XLC.
In the respective Hardware Manuals, you will find detailed descriptions about
connecting the SEQUENZA 10 speakers and the settings necessary on the System
Controller CD 44. SONA SUB
Stacking the Subwoofers
- Securely place the bottom subwoofer onto a level surface.
- Stack the subwoofers on top of one another.
Make sure that the stacking feet of subwoofers stacked on top of one another are securely positioned in the grooves of the lower speaker.
You must additionally secure vertically standing stacked NOMOS XLC systems from falling since the structural safety is not guaranteed, otherwise.
Cardioid Arrays with Controller CD 44
The subwoofer NOMOS XLC is a cardioid loudspeaker.
A cardioid array results in an increase of sound pressure towards the front
because of the rear-facing subwoofer. In the rear area (cardioid) or in the
lateral side area (hypercardioid), on the other hand, the sound pressure is
clearly reduced.
With this, you achieve
- less unwanted sound on the stage
- low feedback
- simplified miking
- improved room acoustics with fewer reflections from the rear and side walls, or – when flown – from the ceiling
- simplified adherence of sound emission limits and therefore less noise disturbance for nearby residential areas during open air events.
6.1 Setup instructions for a cardioid array
In order to implement a cardioid or hyper-cardioid setup, the fronts of the
speakers must face the audience.
When cardioid speakers are put on the floor, ensure that there is always a
distance of at least 40 cm between and over the speakers.
We recommend a safe distance to a possible obstruction of at least one meter
(1 m). Distance at standing speakers:
Distance at lying speakers: 6.2
LSBlocks for cardioid useNOMOS XLC
The following cardioid or hypercardioid setups are available in the K&F CD 44.
All setups with a cutoff frequency other than 60 Hz have a cutoff frequency of
100 Hz.
Operating mode | Chassis | LSBlocks (NOMOS LT) |
---|---|---|
‘Cardioid’ | front | NOMOS LT C-F |
rear | NOMOS LT C-R | |
‘Hypercardioid’ | front | NOMOS LT H-F |
rear | NOMOS LT H-R | |
‘Infrabass Cardioid’ | front | NOMOS LT C-F60Hz |
rear | NOMOS LT C-R60Hz | |
‘Infrabass Hypercardioid’ | Front | NOMOS LT H-F60Hz |
Rear | NOMOS LT H-R60Hz |
Fuse in the NOMOS XLC
To increase the operating safety of the NOMOS XLC, the subwoofers are equipped
with fuses at the signal input. These fuses reduce the risk of consequential
damage resulting from a short circuit (i.e. charred cables / connectors / fire
damage).
7.1 Replacing the Fuses
The fuse holder is behind the rear chassis.
Replace the fuse with the following original fuse only:
Bussmann S 506-8A, T 250 V
Connection
The operating safety and the highest-possible performance is only guaranteed
in conjunctionwith the K&F Topas or K&F SystemRack.
8.1 Terminal assignment 8.2 Cabling a K &F System Rack 8.3 Connecting the NOMOS XLC
The following connecting diagram shows an example with the K&F CD 44 Routing
‘1 in 4 out’.
A maximum of 3 NOMOS XLC subwoofers can be driven by one K&F SystemRack. If
you want to use 3 NOMOS XLC subwoofers with a K&F SystemRack you will need the
Break Out Box ‘K&F BOB-C’ available as an accessory.
Dimensions NOMOS XLC
Weight: 95.0 kg
Measuring Diagrams
Polar Patterns Frequency response
Technical Specifications
NOMOS XLC
Concept| Bass reflex system
Operated with| K&F PLM+ Serie, K&F D-Serie, K&F SystemRack, K&F TOPAS
Lower cut-off frequency| 28 Hz (-10 dB)/33 Hz (-3 dB)
Coverage| Cardioid/Hypercardiod
Nominal power handling| 1,000 watts (front)
500 watts (rear)
program| 2,000 Watt (front)
1,000 Watt (rear)
peak| 4,000 watts (front)
2,000 watts (rear)
Max. SPL (1 m)| 139 dB (SPL Peak/1 m/half space)
Impedance nominal| 4 Ohm (front)
8 Ohm (rear)
loudspeaker/channel| see matrix
Components| 3 x 18“ long excursion chassis, 100 mm voice coil with double
centring, internal and external ventilation, demodulation ring for minimal
distortion
Connection| 2 x Speakon® 4-pin NLT4MP front speakers: 1+ / 1rear speaker: 2+ /
2IN parallel to OUT
Enclosure Design
Frame reinforced enclosure, 15 mm multiplex with highly resilient Polyurea
synthetic black coating, 8 ergonomical butterfly handles, 8 nonabrasive
plastic sliders, 8 stacking grooves for save stacking of identical enclosures,
4 x 100 mm transport castors, 2 locking profiles for transport optional
transport cover, ballproof steel grille with exchangeable black acoustic foam
Dimensions (H x W x D)| 1.200 x 600 x 903 mm
Weight| 95.0 kg/Transport Cover: 8.7 kg (optional accessorie)
EC Declaration of Conformity
Manufacturer:| Kling & Freitag GmbH
Junkersstraße 14
30179 Hannover
Germany
---|---
Authorized representative for the compilation of the technical documents:|
Kling & Freitag GmbH
Abt. Entwicklung
049 (0)511 96997-50
Germany
Product:| Loudspeakersystem
NOMOS XLC
We declare that the designated product is in conformity with the protection requirements imposed by the following EU directives:
- 2014/35/EU, Niederspannungsrichtlinie
- 2014/30/EU, Electromagnetic Compatibility
- 2011/65/EU, RoHS II
Conformance of the products with the requirements is approved by compliance with the following harmonized European standards:
- DIN EN/ISO 60065 : 2002/A12:2011
- Eurocode 1/DIN EN 1991-1-1 : 12/2010
- Eurocode 3/DIN EN 1993-1-1 : 12/2010
- Eurocode 9/DIN EN 1999-1-1 : 12/2010
- EN 55103+1 : 2009+A1 : 2012
- EN 55103-2 : 2009
National regulations:
- DGUV, Regulation 15 (BGV C1)
Hannover, 9th November 2017 Jürgen Freitag
(Managing Director / CEO)
Accessories
Protective Cover NOMOS XLC Transport Cover NOMOS XLC K &F BOB-C:
Speaker signal distributor, 1 x 8-pin into 3 x 4-pin. For operations of 3 x
NOMOS XLC with a K&F SystemRack.
Transportation and Storage
The housing of the speaker is protected against short-term moisture by a
coating. despite, be sure to store, transport, and use the accessories in dry
environments only. The NOMOS XLC System is not designed for long-term use in a
corrosive environment.
Make sure that the system is adequately ventilated during longer storage
periods so any residual moisture can escape from the equipment.
Furthermore, you should ensure that the NOMOS XLC System is protected from
mechanical strain to prevent possible damage.
We recommend using the optional soft cover.
Disposal
15.1 Regulations for Disposal
15.1.1 Germany
Don’t dispose of waste electrical equipment through household waste.
Don’t deliver it to official recycling points either.
All KLING & FREITAG products are plain business-to-business (B2B) products.
Therefore, KLING & FREITAG GmbH is exclusively responsible for disposing of
all KLING & FREITAG waste equipment marked with a garbage-can icon. Call the
below phone number when you have a KLING & FREITAG product (marked with the
garbage-can icon) for disposal. We will offer you a straightforward and
professional disposal at no cost.
KLING & FREITAG equipment with no such icon was sold before 24 March 2006; in
that case, the owner is legally responsible for disposal. We will, however,
gladly assist you by naming appropriate ways of disposal.
For further disposal information of KLING & FREITAG waste products, call +49
(0)511-96 99 7-0 Background information: The Electrical and Electronic
Equipment and Appliances Act (ElektroG) is the German implementation of the
European (EU) Waste Electrical and Electronic Equipment Directive (WEEE,
2002/96/EC).
Therefore, starting on 24 March 2006, KLING & FREITAG GmbH has marked all
products subject to the WEEE that are distributed in Germany with an icon
showing a crossed-out garbage can with a white bar below it. The icon
indicates that the equipment was distributed on or after 24 March 2006 and
must not be disposed of through household waste.
KLING & FREITAG GmbH is legally registered as a manufacturer with the German
wasteequipment registration authority (EAR). The WEEE registration number is:
DE64110372.
We substantiated towards the EAR that our products are for B2B trade only.
15.1.2 EU, Norway, Iceland, and Liechtenstein
Don’t dispose of waste electrical equipment through household waste.
Starting on 13 August 2005, KLING & FREITAG GMBH has marked all products
subject to theWEEE directive that are distributed in any member state of the
European Union (except Germany), Norway, Iceland, or Liechtenstein with an
icon showing a crossed-out garbage can with a white bar below it. The icon
indicates that the equipment was distributed on or after 13 August 2005 and
must not be disposed of through household waste.
Unfortunately, the European WEEE directive was implemented in different
national legislation in the EU member states, making it impossible to offer a
consistent disposal solution throughout Europe.
The local distributor (sales partner) in the respective country is responsible
for complying with the applicable legislation.
Contact your retailer or the local authorities for information on the
regulations applicable in any EU member state (except Germany).
15.1.3 All Other Countries
Contact your retailer or the local authorities for information on the
regulations applicable in any country not listed above.
KLING & FREITAG GMBH © 2017
Version 4.6
Documents / Resources
|
KLING FREITAG NOMOS XLC Performance Cardioid
Subwoofer
[pdf] User Manual
NOMOS XLC Performance Cardioid Subwoofer, NOMOS XLC, Performance Cardioid
Subwoofer, Cardioid Subwoofer, Subwoofer
---|---
References
- der Freitag — Die Wochenzeitung für Politik, Wirtschaft und Kultur
- Affordable PDF tools: PDF Merger, Splitter, Password Security, Converter etc. Free download. [A-PDF.com]
- Home - Kling & Freitag Sound Systems
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>