FUTECH Quattro MM Millimeter Recipient Instruction Manual
- June 17, 2024
- FUTECH
Table of Contents
futech-tools.com
QUATTRO MANUAL
Quattro MM Millimeter Recipient
| Display
---|---
1. Magnet| 17. “Rotary laser” mode
2. LED indicator (orange)| 18. “Line laser” mode
3. LED indicator (green)| 19. Beeper Volume High
4. LED indicator (red)| 20. Beeper Volume Low
5. Laser-sensitive area| 21. Beeper Volume Off
6. Marking notch| 22. Battery Low
7. Clamp| 23. Battery OK
8. On/Off| 24. Accuracy: Coarse, 3mm
9. Volume / Operating mode| 25. Accuracy: Medium, 2mm
10. Accuracy / LED activation| 26. Accuracy: Fine, 1mm
11. Bubble vial| 27. Much too low / Fast interval tone
12. Display| 28. Too Low / Fast interval tone
13. Type plate with serial number| 29. On-grade / Continuous tone
14. Fixing thread for the clamp| 30. Too high / Slow interval tone
15. Beeper| 31. Much too high / Slow interval tone
16. Battery door and latch| 32. No laser / No tone
Depending on the selected operating mode, the receiver detects either the
laser beams (red and green) of rotating lasers or the (horizontal or vertical)
laser lines of line lasers with hand-held receiver function.
Any other use than the described above shall be deemed to be improper use.
First use
Avoid violent shocks or dropping the unit.
Inserting/changing the battery
- Change tha battery if the batterysym bol (22) is displayed.
- Open the battery cover (16)
- Remove tha battery and insert a new one (observe correct polarity)
- Dispose ofthe used battery (see chapter on environmental protection)
Operating
Switching the device on / off
Press the On / Off button (8)
Adjusting the volume
Press the volume button (9) briefly, if necessary repeated∙
- switches the beeper volume between High/Low/Off
Selecting the operating mode
Press the volume button (9) for at least 3 seconds.
- switches from rotating laser to line laser and vica versa
Adjusting the accuracy
Press the accuracy-button (10) briefly, if necessary repeated
- switches the accuracy of readings between Coarse/Medium/Fine
Activating/Deactivating the LEDs
Press the accuracy-button (10) for at least 3 seconds.
Operating
- Hold the device vertically (in case of a vertical laser plane: horizontally) and move it to the laserplane.
- Please pay attention to the acoustic signals and arrows on the (LED) display.
NOTE
- When the device is switched on, it is in the operating mode used before it was switched off.
- If in line laser mode, the device detects only the line laser type which was first detected after the power on.
Maintenance and Care
- Keep the device always clean, especially the laser-sensitive area!
- Do not use aggressive cleaning agents or solvents.
- If soiled heavily the device can be cleanedunder running water.
- Do not use high-pressure cleaner.
- Allow it to dry completely before storing it in a closed container. Residual moisture can result in corrosion of the battery contacts. In this case our warranty expires.
- In the unlikely event of a failure or defect, have the appliance examined and repaired by Futech.
- In all your queries and spare part orders, always quote the serialnumber (see type plate) of your device.
TECHNICAL SPECIFICATIONS
| suitable lasers | red & green/rotating & cross-line |
|---|---|
| maximum range | cross-line: 60m |
rotating: 200m
height of reception field| 60mm
front indicator| lcd + led
reat indicator| lcd
distance to laser indicator (in mm)| no
suitable laser frequencies (in receiver mode)| 5-10khz
accuracy| 1-2-3 mm
protection| ip67
dimensions| 64 x 205 x 130 mm
weight| 0,35 (0,53 with accessories)
DECLARATION OF CONFORMITY
We herewith declare that this product conforms with the following standards
and directives:
Standards
DIN EN 61000-6-1
DIN EN 61000-6-3
in accordance with the regulations stipulated in the directives:
EC Directive
2004/108/EG
2006/95/EG
Technical changes reserved.
We accept no liability for printing errors.