futech-tools 036.3DG 3D 18V Max Green User Manual

September 28, 2024
futech-tools

futech-tools 036.3DG 3D 18V Max Green

Specifications:

  • Model: 036.3DG Multicross 3D 18V MAX Green / 036.4DG Multicross 4D 18V MAX Green
  • Charging Port: USB Type-C
  • Battery: 18V MAX

Product Usage Instructions

First Time Usage:

  1. Connect the battery adapter to the device.
  2. Ensure the battery voltage is above 14V to enable the device to work properly.

Battery Connection:

  1. Insert the battery into the battery adapter.
  2. Make sure the battery indicator [B] shows sufficient power.

Use Self Levelling Mode:

  1. Ensure the device is on a stable surface.
  2. Activate self-levelling mode for automatic levelling.

Manual Slope Mode:

  1. Set the device to manual slope mode to project sloped lines at desired angles.
  2. Tilt the device to set the desired slope.

Horizontal Lines:

  1. Activate horizontal lines based on your working requirements.
  2. Deactivate or activate specific horizontal lines as needed.

Vertical Laser Lines:

  1. Activate vertical laser lines for accurate alignment.
  2. Use the fine adjustment wheel [05] to position the vertical laser lines correctly.

Frequently Asked Questions (FAQ):

  • Q: What should I do if the voltage goes below 14V?
    A: If the voltage drops below 14V, the device will stop working. Recharge or replace the battery to continue using the device.

  • Q: How do I know when to use the laser receiver?
    A: In brightly lit workplaces, such as outdoors in sunlight, use a laser receiver to detect laser lines accurately.

USER
MANUAL
036.3DG MULTICROSS 3D 18V MAX GREEN 036.4DG MULTICROSS 4D 18V MAX GREEN

Manual in your language?
Check the back cover

OVERVIEW

CASE

  • 01 USB Type-C charging port 02 Battery adapter
  • 03 On/Off switch / Pendulum lock 04 Keypad
  • 05 Fine adjustment wheel
  • 06 Upper horizontal laser line 07 Bottom horizontal laser line 08 Front vertical laser line
  • 09 Side vertical laser line
  • 10 1/4” and 5/8” tripod tread

KEYPAD

  • A Power button
  • B Battery indicator
  • C Receiver mode button
  • D Front vertical laser line button
  • E Side vertical laser line button
  • F Upper horizontal laser line button G Bottom horizontal laser line button H Warning triangle
    I Receiver indicator

SAFETY

Please read the safety instructions provided as separate booklet with the device.
LASER RADIATION – Class 2 Laser product. – Do not stare into beam

BATTERY

DIFFERENT BATTERY TYPES

This device works with the 18V batteries of following brands:

  • Bosch
  • Dewalt
  • Festool
  • Hikoki
  • Makita
  • Metabo
  • Milwaukee

NOTE
If the voltage goes below 14V the device stops working. The battery indicator [B] shows the amount of power that is left in the battery until it reaches the minimum level of 14 V.

BATTERY CONNECTION
Before connecting the 18V battery, please remove all dust and sand.

  • Place the right battery adapter [02] on the device. The adapter is mounted correctly when you hear a click.
  • Slide the corresponding battery on the battery adapter [02].

CABLE CONNECTION

This device can also be used with an USB Type-C cable plugged into the USB Type-C port [01].
Only use the power adapter provided by the manufacturer.

IMPORTANT
The power adapter is only to use the laser device without battery. Do not use this power adapter to charge the 18Vbatteries.

FIRST TIME USAGE

  • Remove any protective films where applied.
  • Please only use an 18V battery with the correct adapter.

USE

SELF LEVELLING MODE

  • Shift the Pendulum lock [03] to the “Unlock” position to unlock the pendulum and switch on the laser.
    • At this point the laser is able to level itself.

The device is capable of self-levelling within a range of approximately 3,5°. Ensure the instrument is not placed on a slope exceeding this limit. Should the slope exceed 3,5°, the laser lines will blink fast and the laser will start beeping.

  • To switch off the laser, shift the Pendulum lock [03] to the “Lock” position.

Now the laser is switched off and the penulum is locked again.

MANUAL SLOPE MODE

In manual slope mode, you can set slopes with the Multicross 3D/4D 18V MAX.
This means the laser lines will be projected with the pendulum locked. This gives you the opportunity to project sloped lines under the angle you need.

  • Make sure the Pendulum lock [03] is in the “Lock” position.
  • Switch on the laser by holding the Power button [A] for approx. 3 seconds.

The laser lines switch on with the pendulum locked.
Now, the laser line can be set to the desired slope by tilting the device accordingly.

NOTE
The laser lines are not levelled using the manual slope mode therefor the warning triangle [H] starts fl ashing! To remind you, the laser line will blink shortly every 10 seconds.

  • To turn off the laser in manual slope mode, hold the Power button [A] again for 3 seconds or shift he Pendulum lock [03] to the “unlock” position and back to the “lock” position.

CHOOSE HORIZONTAL AND VERTICAL LINES
At times, you may not require all laser lines, make it useful to activate only the ones needed. Therefore, you have the option to deactivate or activate specifi c laser lines as desired.

  • If all laser lines are switched off, the warning triangle [H] will fl ash at a fast rate and the laser will beep every 10 seconds.
  • When working in manual slope mode and a laser line is activated the warning triangle [H] will flash.

HORIZONTAL LINES

  • Press the Upper horizontal lines button [F] to activate the upper horizontal line.
  • Press the bottom horizontal laser line button [G] to activate the bottom laser line. (Only for MC4D)

NOTE
We advise to set the horizontal line on your working height.

VERTICAL LASER LINES

  • Press the Front vertical laser line button [D] to activate the front vertical laser line
  • Press the Side vertical laser line button [E] to activate the side vertical laser line.

RECEIVER MODE

  • If the workplace is brightly lit, e.g. outdoors in the sun, it may be necessary to use a laser receiver.
  • Press the Receiver mode button [C] to turn on the receiver mode.

When this mode is activated, the receiver indicator [I] will light up. At this moment, laserlines can be detected by the laser receiver.

  • Press the receiver mode button [C] again to turn off the receiver mode.

NOTE
All Futech laser will use 10Khz as frequency in receiver mode. Only receivers that can detect laser lines at 10KHz are compatible.

FINE ADJUSTMENT
You can turn the fi ne adjustment wheel [05] to get the vertical laser lines in the right place. The laser will rotate around the crossing of the two vertical lines. When you feel the brake, stop turning the fi ne adjustment wheel [05].

TECHNICAL SPECIFICATIONS

BATTERY ADAPTERS

Battery adapters are needed to use the laser with an 18V battery.

  • Compatible with Bosch: Art. H036.BOS
  • Compatible with Dewalt: Art. H036.DEW
  • Campatible with Festool: Art. H036.FES
  • Compatible with Hikoki: Art. H036.HIK
  • Compatible with Makita: Art. H036.MAK
  • Compatible with Metabo: Art. H036.MET
  • Compatible with Milwuakee: Art. H036.MIL

All battery adapters are sold separately.

DECLARATION OF CONFORMITY
Futech (Belgium) declares under its own responsibility that this device:

  • 036.3DR, MULTICROSS 3D 18V MAX

  • 036.4DR, MULTICROSS 3D 18V MAX
    is in conformity with the standards
    EMC DIRECTIVE 2014/30/EU:

  • EN IEC 61326-1: 2021

Lier, Belgium,
April, 2024
Patrick Waûters

USER MANUAL
other languages:

DA DANSK
DE DEUTSCH
ES ESPAÑOL
ET EESTI KEEL
FI SUOMEN KIELI
FR FRANÇAIS
IS ÍSLENSKA

ITALIANO
NL NEDERLANDS
NO NORSK
PT PORTUGUÊS
SL SLOVENŠČINA
SV SVENSKA

Facebook
@futechtools
LinkedIn
futechtools
World Wide Web
futech-tools.com
YouTube
@futechtools

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals