MUNBYN IMP002 Bluetooth Receipt Printer User Guide

June 17, 2024
MUNBYN

MUNBYN IMP002 Bluetooth Receipt Printer User Guide

Introduction

This document introduces the setup procedure for the IMP002.

Please read the instructions before using the printer.

For further instructions, please refer to the IMP002 Thermal Printer manual.

IMP002 Thermal Printer Manual: munbyn.biz/002userManual

Notice: When dealing with links that require attention to case-sensitive letters and numbers, it’s important to be mindful of the exact casing used in the link.

Check the Packing List

Check the Packing List
In case of omission or damage, don’t hesitate to contact us via the contact details below.

support@munbyn.com
+1 6502062250
Munby
Monday to Friday 24 hours

Overview

**Printer Overview

**

Function of the button

Button Picture Functions
Power button Hold the button for two seconds until you hear two beep Turn on
Power button Hold the button for two seconds until you hear one beep Turn

off
Feed button| Click| Paper output
Power button & Feed button| In the shutdown state, hold down the FEED button on the printer first, then press the Power button until you hear two beeps and see the status light flash red, then release your hand| Print self-test paper

Indicator light status

Power Indicator Light| Status Indicator Light| Status| Situation
---|---|---|---
Green| | Light (The status indicator light is off when the power is ready)| Standby (Bluetooth not connected)
Power Indicator Light| Status Indicator Light| Status| Situation
---|---|---|---
Green| | Flash| Charging
Green| | Light always on| Printing or the power is fully charged in power on mode
Green| Green| Light| Standby (Bluetooth connected)
Green| Red| Flashing Red and the printer beeps (500ms/time)| Out of paper
Green| Red| Flashing Red and the printer beeps (500ms/time)| Cover is not closed
Green| Red| Flashing Red (200ms/time)| Printer head is overheated. Printer startup over-temperature protection

Prepare before using

Li-ion battery installation

  1. Refer to the picture, push the battery cover in the direction of the arrow.

  2. Put the battery in the battery slot.

Notice: Install the positive pole to the left-do not install it backwards.

  1. Close the battery case.

Paper Loading

Paper Loading

  1. Pry open the hood from the grooves on both sides and then open the lid.
  2. Load a paper roll in the direction shown in the illustration.
  3. Pull the end of the paper out a little and push down the printer’s top cover to close.
    Notice: If the device remains idle for 1 hour, it will automatically shut down. This feature is designed to reduce battery consumption during prolonged standby mode.

Initial Setup

Set Up the IMP002 for First Use on Android

Before connecting to the Bluetooth printer, you need to print a self-test page to view the machine’s Bluetooth name and connection password. (For details on the self-test page, refer to Figure 5-2. For printing the self-test page method, refer to section 3.2).

How to Connect a Bluetooth Printer?

  1. Put the thermal paper into the printer and press the printer power button to turn on the printer.

  2. Turn on the Bluetooth on your phone. Search Bluetooth device [P502A-6036] and connect it.
    Notice: The suffix digits (last 4 digits) of the device’s Bluetooth name are different primarily to distinguish the situation when multiple devices are used for printing.Bluetooth Printer

  3. Enter pairing code [0000] and click [Pair]. Then the mobile phone is successfully connected to the printer via Bluetooth.

How to connect a Bluetooth printer to Louvers POS for printing order receipts?

  1. Turn on the Bluetooth on your phone. Search Bluetooth device [P502A-6036] and connect it.

  2. Run [Loyverse POS] and set printer from [Setting] →[Printers].

  3. Click on the [+] button in the bottom right corner to add a printer. The printer’s name can be anything you like. Printer model, select [Other model] → [Interface], select [Bluetooth].

  4. Click [SEARCH] and select [P502A-6036] connection.
    Bluetooth Printer

  5. Paper width, select [58mm].

  6. From [Advanced setting], set [Cutter ESC/POS commands], input [0A,0A,0A,1D,56,42,00].
    Bluetooth Printer

  7. Turn on two selections: [Print receipts and bills], [Automatically print receipts]. Then, you can [PRINT TEST] at the bottom. Connection is successful.

Connect the Louvers POS to print order receipt according to the video.

Demo video: munbyn.biz/002loyverse
QR Code

Set Up the IMP002 for First Use on Windows

Download Windows Driver

You can get the driver by clicking the link below to download the driver.

Driver download: munbyn.biz/002driverW Setting tool download: munbyn.biz/002WTool Only supports USB connection.

Notice: When dealing with links that require attention to case-sensitive letters and numbers, it’s important to be mindful of the exact casing used in the link.

USB Interface
USB Interface

  1. Connect the printer to the power outlet via the power cord.
  2. Connect the printer to your Windows computer via USB.
  3. Place the thermal paper into the printer and power it on.

Open the downloaded driver and install it.
Demo video: munbyn.biz/002wi
QR Code

Set Up the IMP002 for First Use on MacBook

Download MacBook Driver

You can get the driver by clicking the link below to download the driver.

Driver download: munbyn.biz/MACD

Only supports USB connection

USB Interface
USB Interface

  1. Connect the printer to the power outlet via the power cord.
  2. To connect the printer to your Mac, plug one end of the USB cable into your Mac’s USB port and the other end into the printer. Use a USB-A to USB-C adapter for Macs with a USB-C port if needed.
  3. Place the thermal paper into the printer and power it on.

Open the downloaded driver and install it.
Demo video: munbyn.biz/002wi
QR Code

Set Up the IMP002 for First Use on Chromes

Download Chromes Driver

You can click the link below to download the driver. Driver download link: munbyn.biz/002chromeos Only supports USB connection.

USB Interface

  1. To install the [POS Printer Manager] extension and connect your ticket printer, you need to add the extension in your browser.
    Specific steps are as follows:
    a. Open the browser and click on the three dots in the top right corner of the browser menu. Select [More tools], and select [Extensions].
    Specific steps are as follows:
    b. Click [Chrome Web Store].
    Specific steps are as follows:
    c. Search [POS Printer manager] on Google Store and click [Add to Chrome].
    Specific steps are as follows:
    d. Click [Add extension]. You can now see the installed [POS Printer manager] extension program on the page.
    Specific steps are as follows:

  2. Connect the printer to the power outlet via the power cord, and connect the printer to your Chrome Book computer via USB. Place the thermal paper into the printer and power it on.
    USB Interface
    Connect the printer according to the video. Chrome OS Connection System demo video: munbyn.biz/002chromeosvideo
    QR Code

Contact us

MUNBYN provides 18 months warranty and lifetime free service.

If you encounter any issues with the product, don’t hesitate to contact the MUNBYN team to receive troubleshooting tips or a prompt replacement

Email: support@munbyn.com (24-7 online support)

WhatsApp: +8618144898200

Phone: +1 6502062250

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to protect reasonably against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation, if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals