TYGER TG-LX3D82348 LanderX Running Board Instruction Manual

TYGER TG-LX3D82348 LanderX Running Board

Product Information

Specifications:

• Brand : TYGER
• Model : LanderX
• Part Number: TG-LX3D82348
• Material : Various materials including metal and plastic components
• Weight : Varies based on components

Product Usage Instructions:

Before Installation:
Read all instructions carefully before starting the installation process. Ensure all parts are present by verifying the contents of the box. Any missing parts or damage should be documented with pictures for claim purposes at www.tygerauto.com/contact.

Torque Values:
Refer to the provided torque values based on fastener size and class to ensure proper installation and secure fit.

Installation Procedure:

1. Step 1: Begin at the driver side-front of the vehicle. Remove sealing tape covering factory holes in the inner panel.
2. Step 2: Follow specific instructions for attaching the driver side front bracket based on your model/year. Use provided components like Bolt/Nut Plates, Hex Bolts, Plastic Retainers, and other hardware as needed.

Frequently Asked Questions (FAQ):

Q: What should I do if I find missing parts or damage during installation?
A: If any parts are missing or damage is found, take pictures for claim purposes and visit www.tygerauto.com/contact to file a claim.

TYGER LanderX
TG-LX3D82348

BEFORE INSTALLATION

READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT

TORQUE VALUES

PROCEDURE:

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. DRILLING MAY BE REQUIRED.

1. STEP 1 Starting at the driver side-front of the vehicle, remove the sealing tape covering the factory holes in the side of the inner panel (Fig 1). 

2. STEP 2 Determine the correct procedure to attach the driver side front Bracket for your model/year:
   Models without factory threaded inserts in body panel:

   • Select (1) 8mm Bolt/nut Plate (Fig 2). Partially thread an 8mm Hex Bolt onto the threaded of the Nut Plate (Fig 3). Thread the Hex Bolt in until it is flush with the welded nut. Use the Hex Bolt as a handle and insert the Bolt and Nut Plate into the oval hole (Fig 4). Feed the threaded bolt on the Bolt Plate through one of the hex shaped factory holes.

   • Thread (1) 8mm Plastic Retainer onto the threaded end and down tight against the body panel (Fig 5). NOTE: The Plastic Retainer is designed to keep the Bolt/Nut Plate from falling into the body panel and to aid in Bracket installation.

   • Select (1) Driver/Left Bracket (Fig 6). Attach the Bracket to the threaded end of the Bolt Plate with (1) 8mm Flat Washer, (1) 8mm Lock washer and (1) 8mm Hex Nut (Fig 6).
     IMPORTANT : Driver/Left Front Bracket is the same as the Driver/Left Center and Passenger/Right Rear Brackets. DO NOT tighten hardware at this time.

   • Remove the 8mm Hex Bolt from the nut on the Bolt Plate from STEP 2a. Rotate the Bolt on the Bolt Plate until the threaded nut lines up with the remaining hole in the Mounting Bracket and body panel (Fig 7). Attach the Bracket to the threaded Nut Plate with (1) 8mm x 30mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer (Fig 7). DO NOT tighten hardware.

   • Models with factory threaded inserts:
     Attach (1) Driver/Left Mounting Bracket to the threaded inserts with (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washer (Figs 8 & 9). DO NOT tighten hardware.

3. STEP 3
   Next, attach the Bracket to the back of the pinch weld with (2) 6mm Button Head Bolts, (4) 6mm Flat Washers, (1) 16mm x 60mm Spacer Plate and (2) 6mm Flange Nuts (Fig 10A). DO NOT fully tighten hardware at this time.

   • DO NOT fully tighten hardware. IMPORTANT: 2009-12 models not equipped with factory holes will require drilling through the pinch weld to fully attach Bracket. DO NOT drill through pinch weld at this time, (see STEP 7).

4. STEP 4

   • Move along the side of the body panel to the center mounting location (Fig 11). Repeat the appropriate STEPS 2-4 to install the Driver/Left Center Bracket. IMPORTANT: The Center Mounting Bracket will use the 16mm x 34mm Spacer Plate (Fig 10B).

5. STEP 5
   Move to the rear location (Fig 12). Repeat STEPS 1-3 to attach (1) Driver/Left Rear Mounting Bracket to the driver/left rear mounting location.

6. STEP 6
   Select the Driver/Left TYGER LanderX. Place the TYGER LanderX onto the Mounting Brackets and attach with (6) 8mm Combo Bolts (Fig 13). DO NOT tighten hardware.

7. STEP 7
   Properly level and adjust the TYGER LanderX and fully tighten all hardware.
   2009-12 models requiring drilling through pinch trim:

   • Level the TYGER LanderX to the vehicle. Make sure all (3) Brackets are tight against the bottom of the body panel and tighten all mounting hardware.
   • Mark the location of the slots onto the pinch weld.
   • Drill (2) 1/4” holes through the pinch weld for each Bracket. IMPORTANT: DO NOT drill too close to the bottom edge of the pinch weld. Drill the holes in the center of the marked slots.
   • Repeat STEP 3 to attach the Brackets to the drilled holes in the pinch weld. Check for level then fully tighten all hardware.

8. STEP 8
   Repeat STEPS 1-7 to attach the Passenger/Right TYGER LanderX.

9. STEP 9
   Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>