TYGER TG-LX3C82328 LanderX Running Board Instruction Manual
- June 17, 2024
- TYGER
Table of Contents
TYGER TG-LX3C82328 LanderX Running Board
Specifications
- Model: TG-LX3C82328
Torque Values
-
* 6mm: 6-7 ft-lbs
- 8mm: 15-16 ft-lbs
- 10mm: 31-32 ft-lbs
- 12mm: 54-55 ft-lbs
- 14mm: 87-88 ft-lbs
Product Usage Instructions
Before Installation
Read the instructions carefully before starting the installation. Remove
contents from the box and verify all parts are present. Failure to identify
damage before installation could lead to a rejection of any claim. If missing
parts or any damage found, please take a picture for claim purposes.
Step 1 – Installation Preparation
- Start the installation under the driver/left side of the vehicle.
- Locate the tabs along the bottom edge of the body (pinch weld).
- Determine the mounting locations for the Mounting Brackets.
Step 2 – Bracket Installation
- Determine the correct procedure for each Bracket location.
- Attach Mounting Brackets to the designated locations using specified hardware.
- Do not tighten hardware at this stage.
Step 3 – Final Installation
Proceed with tightening the hardware securely to complete the installation.
Frequently Asked Questions (FAQ)
-
Q: Where can I file a claim for missing parts or damage?
A: To file your claim, please visit: www.tygerauto.com/contact -
Q: What should I do if my model has a DEF tank?
A: Select a flat, level area for installation. It may require cutting.
BEFORE INSTALLATION
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT
TORQUE VALUES
Fastener Size | Class 8.8 Torque (ft-lbs) | Class 10.9 Torque (ft-lbs) |
---|---|---|
6mm | 6-7 | 6-7 |
8mm | 15-16 | 22-23 |
10mm | 31-32 | 44-45 |
12mm | 54-55 | 78-79 |
14mm | 87-88 | 125-126 |
- Driver/Left TYGER LanderX
- Passenger/Right TYGER LanderX
- Passenger/Right Front Upper Support Bracket
- Passenger/Right Front Lower Mounting Bracket
- x3 Passenger/Right Rear Mounting Brackets
- x4 Driver/Left Mounting Brackets
- x1 8mm x 35mm Bolt Plate
- x17 8mm Lock Washers
- 8mm x 24mm x 2mm Flat Washers
- 8mm x 28mm x 3mm Flat Washers
- 8mm Nylon Lock Nuts
- 8mm-1.25mm x 25mm Hex Bolts
- x1 8mm-1.25mm x 40mm Hex BoltsRear Mounting Brackets
- 8mm Clip-On Nuts
- 8mm x 25mm Combo Hex Bolts
PARTS LIST
PROCEDURE
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. ON MODELS WITH DEF TANK, SELECT A
FLAT, LEVEL AREA FOR INSTALLATION. MAY REQUIRE CUTTING.
-
STEP 1
Start the installation under the driver/left side of the vehicle. Locate the 5 tabs along the bottom edge of the body, (pinch weld). Mounting Brackets will bolt to the 1st, 2nd, 4th and 5th mounting tabs (Fig 1). Directly above each tab is a top mounting location on the side of the rocker panel. Hold a Bracket up in place to help determine the mounting holes to use. -
STEP 2
-
Determine the correct procedure for your model year and each Bracket location.
-
Bottom mounting location on the edge of the pinch weld.
-
Flat tab on pinch weld with factory installed weld nut:
-
Thread hex bolt into weld nut from the backside-down to clear paint from threads.
Flat tab on pinch weld with hole: -
Select (1) 8mm Clip Nut. Slide the Clip Nut over the tab with the nut facing up behind the tab (Figs 2 & 3). Line up threaded nut with hole in the tab. Repeat for each mounting location.
-
Locate top mounting location on the back side of the rocker panel.
-
Models with factory installed threaded insert in rocker panel:
-
Thread 8mm Hex Bolt into threaded insert to clear paint as required (Figs 2 & 3).
Large and small hole in side of body panel: -
Remove the rubber plug from the larger hole (Fig 4). Select (1) 8mm Clip Nut. Slide the Clip Nut into the larger hole. Line up the threaded nut with the smaller hole
-
-
STEP 3
Select (1) Driver/Left Mounting Bracket. Attach the Mounting Bracket to the Clip Nuts and/or the factory threaded holes with (2) 8mm x 25mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm x 24mm Flat Washers (Fig 5). DO NOT tighten hardware.. -
STEP 4
Repeat STEPS 1-3 to attach remaining (3) Driver/Left Mounting Brackets to the Driver/Left side. -
STEP 5
Select the Driver/Left TYGER LanderX. Attach the Step to the Mounting Brackets with (8) 8mm Combo Bolts (Fig 6). DO NOT tighten hardware.
Driver/Left Side Installation Pictured -
STEP 6
Move to the passenger/right side of the vehicle. Determine if the vehicle is equipped with a plastic diesel exhaust fluid (DEF) tank (Figs 7 & 8).
Models without DEF tank, skip to STEP 7.
Models with DEF tank: The tank sits close to the side of the body. With specialized tools, the Passenger/Right Front Upper and Lower Mounting Brackets can be installed but room is very limited. Determine model year of vehicle before proceeding. Up to 2016 models:-
It may be easier to drop the tank down to access the inner side of the body panel for upper bracket installation. Tank will not need to be removed, only dropped down for access to mounting location. IMPORTANT: If tank is full, it will be very heavy and assistance
-
is highly recommended to avoid injury or damage to the vehicle or the tank. It is recommended that installation is performed when the DEF tank is low on fluid before dropping the tank.
-
On models with plastic lower tray under the tank, remove the
(3) hex bolts attaching the tray to the frame (Fig 7), and remove the tray. -
Release the tank filler hose. Release the plug for the sending unit on the top of the tank.
-
Support the tank with a floor jack. Place a smooth flat surface,(wooden block for example), between the floor jack and the tank to avoid damaging the plastic tank. DO NOT push up on the tank; only support the weight of the tank with the jack.
-
Remove the (2) bolts securing the tank straps to the vehicle (Fig 8). Tilt the straps to release from the brackets. Slowly lower the tank until the top of the tank is almost visible. Use blocks or stands to support the tank while installing the Front Upper and Lower Brackets.
-
Proceed to STEP 7.
On 2017 models and on: -
If necessary, remove the (4) hex bolts attaching plastic cover to DEF tank (Fig 9) and remove plastic cover for better access. NOTE: On 2017-on 2500/3500 models, only remove plastic cover from DEF tank. Do not lower DEF tank and proceed to STEP 7.
Passenger/Right Front Installation Pictured
-
-
STEP 7
Locate the first tab on the edge of the pinch weld. Select the Upper Bracket (Fig 10). Repeat STEPS 2 & 3 to attach the Passenger/Right Front Upper Mounting Bracket to the side of the rocker panel (Fig 10). DO NOT tighten hardware. -
STEP 8
Line up the hole in the bottom of the Upper Bracket with the hole in the tab on the pinch weld.-
Models with a weld-nut: Slide the Bracket over the weld-nut. Attach the Lower Bracket to the bottom of the body andweld-nut with (1) 8mm x40mm Hex Bolt, (1) 8mm Lock Washer,
(1) 8mm x 28mm Flat Washer, (1) 8mm x 24mm Flat Washer and (1) 8mm Nylon Lock Nut (Fig 12). DO NOT tighten hardware. -
Models with flat tab and hole: Insert the 8mm Bolt Plate down through the hole in the Upper Bracket and tab. Attach the Lower Bracket to the bottom of the body and Bolt Plate with (1) 8mm x 28mm Flat Washer and (1) 8mm Nylon Lock Nut (Figs 12 & 13). DO NOT tighten hardware.
-
-
STEP 9
Secure the rear of the Lower Bracket to the Upper Bracket with (1) 8mm Hex Bolt, (1) 8mm Lock washer and (1) 8mm x 24mm Flat Washer (Fig 14). DO NOT tighten hardware. -
STEP 10
Repeat STEPS 1-3 to attach the remaining (3) Passenger/Right Mounting Brackets to the passenger/right side rocker panel. -
STEP 11
For 2017 2500/3500 DEF tank models: Locate the 2nd mounting location along the bottom edge of the body, (pinch weld) (Fig 1). Hold the DEF cover in place and mark the 2nd Bracket location onto the cover (Fig 15A). Use a sharp knife or hacksaw blade to carefully cut a slot in the plastic cover to clear the 2nd Bracket (Fig 15B). Remove as little plastic as possible. -
STEP 12
Repeat STEP 5 to attach the Passenger/Right TYGER LanderX. -
STEP 13
Once the Sidebar has been attached and all hardware fully tightened, reinstall the DEF tank and cover, if equipped, as described in STEP 6. -
STEP 14
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>