KSANA A03376.79 3 Light Modern Vanity Light Fixture Instruction Manual

KSANA A03376.79 3 Light Modern Vanity Light Fixture

SAFETY INSTRUCTION

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

• Ladder
  

• Phillips head flat blade screwdriver
  

• Electrical tape
  

• Pliers
  

• Wire cutter/Stripper
  

PARTS TYPE & QTY INCLUDING

(E) Mounting plate (1)
(F)Green ground screw (1)
(G) Back plate (1)
(H) Arm (3)
(I) Iron lining (3)
(J) Screw (9)
(K) Knob nut (2)
(L) Glass shade (3)

ACCESSORIES & QTY ENCLOSED

(A) Plastic wire connector (3)
(B) Anchor (2)
(C) Mounting screw (2)
(D) Wood screw (2)(A) Plastic wire connector (3)
(B) Anchor (2)
(C) Mounting screw (2)
(D) Wood screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.

3. Make installation
   Step A1: Unscrew the knob nuts (K) from back plate(G) then gently remove mounting plate (E).
   
   Step A2: Carefully pass wires from outlet box through mounting plate (E). By measuring, determine the correct distance of drilling hole for anchor (B) knocked into wall, then drill holes and gently knock the anchors into wall until them are level to the wall. Attach the mounting plate (E) to outlet box with mounting screws (C) and wood screws(D).
   
   Step A3: Make wire connections
   Connect wires as below wires connecting shown. TAKE NOTE OF YOUR WIRE COLOR OF FIXTURE ,NEVER CONNECT WIRE TO GROUND WIRE
   
   Connect ground wire according to below chart
   
   
   Connect wires according to below chart Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
   ---|---
   Black| White
   •Parallel cord ( round & smooth)| •Parallel cord ( square & ridged)
   Clear, Brown, Gold or Black without tracer| Clear, Brown, Gold or Black with tracer
   Insulated wire ( other than green) with copper conductor| Insulated wire ( other than green) with silver conductor

*Note: When parallel wires ( SPT I & SPT II ) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth ( see illus.)

Twist plastic wire connector until wires are tightly joined together, carefully tuck all wires into the outlet box
Step A4: Put the back plate (G) to the wall, carefully pass the threaded nipple through holes in the back plate and secure them with knob nuts(K).

Step   A5: Fix the glass shade (L) on the iron lining (I) with an screws (J). Install bulb (Not included. Please do not exceed the maximum capacity recommended on the socket.)

4. Check everything is installed properly, then you could turn on the light. Enjoy !
   CLEANING
   To clean, wipe fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
   ORDERING PARTS
   Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>