YITAHOME TLCFLS-2041 20 Caged Ceiling Fan Instruction Manual

YITAHOME TLCFLS-2041 20 Caged Ceiling Fan

Product Specifications:

• Model: TLCFLS-2041
• Product Type: Ceiling Fan
• Power Requirement: 110V

Product Usage Instructions

Safety Guidelines:

1. Turn off electricity before installation.
2. Follow all instructions carefully.
3. Ensure compliance with local electrical codes.
4. Consult a qualified electrician if needed.
5. Maintain sufficient space around the fan.

Before You Start:

1. Ensure power supply is 110V.
2. Hire a qualified electrician for installation.
3. Turn off electricity before working on the fan.
4. Check and tighten all screws during assembly.
5. Avoid touching blades when the fan is running.

Installation Steps:

1. Install the Mounting Bracket:
   • For Concrete Ceiling: Drill holes, insert screws, align bracket holes, and tighten with nuts.
   • For Wooden Ceiling: Secure bracket with screws (ST5*35).

Install the Suspension System:
Remove clevis pin, pass downrod through canopies, connect to fan motor, and insert wires into the downrod.

FAQ (Frequently Asked Questions):

Q: Can this fan be used outdoors?
A: This product is designed for indoor use only, not suitable for outdoor environments.

Q: What should I do if the fan makes unusual noises?
A: Check if all screws are properly tightened and ensure the fan is securely mounted to reduce vibrations that may cause noise.

Thank you for purchasing a YITAHOME product. To ensure correct function and safety,please read and follow all the instructions before using the product.

SAFETY GUIDELINES

1. To avoid possible electric shock, turn off the electricity at the main fuse box or circuit panel before you begin installing or servicing the fan.
2. Read and follow all instructions and safety guidelines carefully before installing.
3. Make sure all electrical connections comply with the local codes or ordinances and the National Electrical Code. If you are unfamiliar with electric wiring, please consult a qualified and licensed electrician.
4. Make sure there is sufficient space to rotate the blades of the fan, which is at least seven (7) feet of clearance between the floor and the fan blade tips. The fan should be mounted at least thirty (30) inches from walls and/or other upright structures.
5. WARNING:The outlet box and ceiling support joist used must be securely mounted, and capable of supporting at least 100 pounds . To reduce the risk of fire, electric shock or personal injury, mount to the outlet box marked“ acceptable for fan support” and use mounting screws provided with the outlet box. The box must be supported directly by the building structure.
6. WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked “acceptable for fan support” and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
7. Electrical diagrams are for reference only. Light kits that are not packed with the fan, which must be UL listed and marked suitable for use with the fan model you are installing . Switches must be UL. general-use switches. Refer to the instructions packaged with the light kits and switches for proper assembly.
8. After assembling, check that all connections are firmly secured.
9. After making electrical connections, spliced conductors should be turned upward and pushed up carefully into outlet box. The wires should be placed separately from the grounded conductor and the equipment-grounding conductor on opposite side of the outlet box.
10. WARNING:To reduce the risk of electrical shock and fire , do not use this fan with any solid-state fan speed control device, or rheostat.
11. Do not operate the reverse switch until the fan has come to a complete stop. 12.Do not insert anything into the fan blades while they are rotating.
12. WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as “flanges”) during assembly or after installation. Do not insert objects into the blades.
13. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan.
14. Do not use water or detergent when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for cleaning.

NOTE:

• The important safety precautions and instructions on the manual are not meant to cover all possible conditions and situations that may occur. It should be understood that common sense and caution are necessary factors during the installation and operation of the fan.
• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities that are different or impaired, or lack of experience and/or knowledge, unless such persons are supervised and/or trained to operate the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not use appliances as a toy.
• You must install a switch or circuit breaker that disconnects all power poles of at least 3 mm between each pole.

BEFORE YOU START

1. The input power for this fan must be 110V .
2. The electrical installation must be carried out by a qualified electrician.
3. To reduce the risk of electric shock, make sure the electricity is turned off before mounting or dismounting the fan. The power cables for assembly must be earth, positive and neutral.
4. Make sure all screws are assembled and tightened during assembly.
5. To reduce the risk of injury, do not touch the blades when the fan is running.

Product Instruction

SCREWS BAG

INSTALLATION STEPS

INSTALL THE MOUNTING BRACKET:

1. Concrete ceiling:
   Drill two holes with 8 mm diameters in the ceiling. Insert two screws into the holes. Then attach the mounting bracket and make its holes align with drilled holes. Tighten the mounting bracket with nuts.(Fig. 1)

2. Wooden ceiling:
   Secure the mounting bracket to the wooden ceiling with screws (ST5*35). (Fig. 2).

INSTALL THE SUSPENSION SYSTEM

1. Remove the clevis pin from the fan. Pass the downrod through the upper and lower canopies to connect to the fan motor assembly. Insert the wires to the downrod. (Fig.3-5)
2. Make sure that the holes of downrod are aligned with the holes of the joint. Insert the clevis pin and pass“ R” pin through the clevis pin hole. Then lock the downrod with screws.(Fig.6-8)
3. Lift the fan assembly onto the mounting bracket. Rotate the fan until the notch on downrod ball engages with the slot of the mounting bracket. (Fig.9- 10)
4. Pass the screw through the wire ring of the ceiling fan, and tighten the screw of the wire for increased safety. (Fig.11-12)

Remote control connection

INSTALL THE UPPER CANOPY

1. Loosen screws at the bottom of mounting bracket but do not remove them. (Fig.11)
2. Raise the upper canopy and align the keyholes at the bottom of the canopy with the screws at the bottom of mounting bracket. (Fig.12)
3. Rotate the canopy until the screws of the mounting bracket drop into the slot recesses. Tighten screws(Fig.13)

OPERATING YOUR FAN

Turn on the power and check the fan’s operation.
The appropriate speed settings of warm or cool weather depend on many factors such as the room size, ceiling height, and fans’ number.

REMOTE CONTROL SETTING AND OPERATION

1. Restore electricity to the outlet box by turning the electricity on at the main fuse box.
2. Remove the battery cover from the remote control transmitter,then put the battery in and fit the cover on.

Note:

1. Use 2 PCS AAA battery to install.

2. If not used for long periods of time, remove the battery to prevent damage to the remote transmitter, and store it away from excess heat or humidity.

3. Switch Indicator

4. Speed Controller

5. Fan Shutdown

6. Fan Swing

7. Natural wind

8. Forward and reverse

9. Timer

10. Timer

Actual use shall be subject to the real product

CONTACT US:
If you have any questions about the installation of YITAHOME® products，just contact us at +1(888)-717-8084 from Mon-Fri 8:00 AM-16:30 PM PST / Saturday 8:00 AM-12:00 PMPST or E-mail us at: after-sale.cs@hotmail.com

Alternative method to contact us(amazon.com orders only)

1. Log into your amazon account
2. Go to “Your Orders” and find the purchase
3. Click on “Contact Seller”

References

• . Spend less. Smile more.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>