TYGER TG-LX3T82428 LanderX Running Board Installation Guide
- June 17, 2024
- TYGER
Table of Contents
TYGER TG-LX3T82428 LanderX Running Board
BEFORE INSTALLATION
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM
BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE
INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY
DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE.
TO FILE YOUR CLAIM, PLEASE VISIT:
WWW.TYGERAUTO.COM/CONTACT
TORQUE VALUES
Fastener Size| Class 8.8 Torque (ft-lbs)| Class 10.9 Torque (ft-
lbs)
---|---|---
6mm| 6-7| 6-7
8mm| 15-16| 22-23
10mm| 31-32| 44-45
12mm| 54-55| 78-79
14mm| 87-88| 125-126
×1 Driver/Left TYGER Lander X
×1 Passenger/Right TYGER Lander X
×1 Driver/left Front Bracket **A**
×2 Driver/Left Center/Rear Brackets **B**
×1 Passenger/Right Front Bracket **C ** ×1 Passenger/right Center/Rear Brackets **D**
×12 8-1.25mm x 30mm Hex Bolts
×12 8mm x 24mm x 2mm Flat Washers
×12 8mm Lock Washers
×12 8-1.25mm x 25mm Combo Bolts
Parts List
Reference the letters printed on the brackets to determine mounting locations
Bottom View
ATTENTION: Refer to the D or P labelling on the tubes to determine the
Driver or Passenger side steps.
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS
RECOMMENDED.
INSTALLATION INSTRUCTIONS
STEP 1
Start the installation under the driver/left side of the vehicle.
Locate the 2 threaded holes in the bottom of the body (Fig 1).
NOTE: Threaded holes might be covered with plugs. Remove plugs from
threaded holes.
Driver/left Side Installation Pictured
STEP 2
Select the driver/left “A” Front Bracket (Fig 2). Attach the Bracket to the
(2) threaded holes with (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers and (2)
8mm Flat Washers (Fig 3). Snug but DO NOT fully tighten the hardware.
Driver/left Side Installation Pictured
STEP 3
Move to the center mounting location (Fig 4). Select (1) driver/left “B”
Center/rear Bracket (Fig 5). Repeat STEPS 1 & 2 to attach the Bracket to the
floor (Fig 6).
Driver/left Side Installation Pictured
STEP 4
Continue on to the last pair of threaded holes close to the rear wheel opening
(Fig 7). Repeat STEPS 1-3 to attach the remaining driver/left “B” Center/rear
Bracket (Fig 8).
STEP 5
Carefully unwrap the TYGER Lander X. Select the driver/left TYGER Lander X.
Note “D” on back of tube. Carefully position the Side Step up to the (3)
Brackets. IMPORTANT: DO NOT slide, (front to back or rotate), the TYGER Lander
X against the Brackets or damage to the finish may result. Attach the TYGER
Lander X to the Brackets with (6) 8mm x 25mm Combo Hex Bolt assemblies (Figs
9-12). DO NOT fully tighten hardware.
Driver/left Side Installation Pictured
STEP 6
Level and adjust the TYGER Lander X and tighten all hardware.
STEP 7
Repeat STEPS 1-6 to install the passenger/right TYGER Lander X.
STEP 8
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>