GOLDEN LIGHTING 6950-FM Shepard Flush Mount Ceiling Light Instruction Manual
- June 17, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 6950-FM Shepard Flush Mount Ceiling Light Instruction
Manual
DIMENSION
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one
pendant for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance
for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.
Love your light and want to show it off? Follow us, share a picture, and tag us on Social…
Assembly Instructions
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT :
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap. 1. Mounting strap (B) contains several pairs of threaded holes. Find the pair of holes that matches the spacing of the holes on the junction box. Mounting screws (C) should be attached to mounting strap (B). Pull the house wires through the center of mounting strap (B). Secure mounting strap (B) to the junction box with mounting screws (C) and a screwdriver. Tighten the screws securely.
ASSEMBLING THE FIXTURE
Gently pull the wires from the nipple (O) on top of the fixture body (N) where sockets (F) are attached. Place the fixture body (N) inside the shade (G) until the nipple (O) and fixture wires protrude from the hole on the top of the shade (G). Place the fixture frame (D) over the top of the shade (G) so that the nipple (O) protrudes through the fixture frame (D). Feed fixture wires through the hole in the fixture frame (D) and pull the wires until taut. Secure the fixture frame (D) to the shade (G) and fixture body (N) using washer (L), ground wire ring (K), washer (M), and hex nut (H). Tighten hex nut (H) using the provided tool (J)until snug to secure.
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and
FINISHING THE INSTALLATION
Carefully lift the assembled fixture body (N), shade (G), and fixture frame (D) up to the mounting strap (B). Align so that the holes on the side of the mounting strap (B) line up with the holes on the side of the fixture frame (D). Thread screws (A) into the holes found on both the side of fixture frame (D) and mounting strap (B) to secure to the mounting strap. Install light bulbs (not included) into the sockets (F) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is now complete. Turn on the power and test the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>