QUOIZEL LWS7970D3 4 Light Pendant User Guide
- June 17, 2024
- QUOIZEL
Table of Contents
- QUOIZEL LWS7970D3 4 Light Pendant
- Product Information
- Product Usage Instructions
- FAQ
- SAFETY INFORMATION
- PREPARATION
- TOOLS REQUIRED
- PACKAGE CONTENTS
- Installation Instructions
- CARE AND MAINTENANCE
- TROUBLESHOOTING
- CONTACT
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
QUOIZEL LWS7970D3 4 Light Pendant
Product Information
Specifications
- Stock Part#: 915739KIT
- Crossbar Assembly: 1pc
- Wire Connector: 3pcs
- Outlet Box Screw: 2pcs
- Quick Link: 2pcs
- Ceiling Canopy: 1pc
- Fixture Chain: 1pc
- Fixture Loop: 1pc
- Socket Assembly: 1pc
- Large Ring: 1pc
- Ring: 1pc
Product Usage Instructions
Adjust Fixture Chain Length
- A – Pull the supply wires and ground wire up through the fixture chain alternating links.
- B – Push the ends of the supply wires and ground wire up through the loop and into the outlet box.
- C – Remove the canopy.
- D – Insert the remaining slack wire into the outlet box.
Loop Installation
- Loop the black or red wire (hot) from the outlet box through the fixture loop.
Connect the ground wire from the fixture with the label G.
Care and Maintenance
- If the light bulb needs replacement, follow the instructions to replace it.
FAQ
- Q: What should I do if I encounter issues with the product?
- A: Please contact our customer service department at 1-844-564-3055 or email cs@quoizel.com for assistance.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
WARNING
- RISK OF ELECTRIC SHOCK – Before beginning installation, turn off electricity at the circuit breaker box or the main fuse box.
- RISK OF FIRE – Use bulbs specified by the markings and/or labels on the fixture.
CAUTION
- For your safety, read the instructions completely before beginning installation.
- If in doubt about electrical installation, consult a licensed electrician.
- Turn off the electricity to the fixture before replacing the bulb(s).
PREPARATION
- Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents list.
- If any part is missing or damaged, do not attempt to assemble the product.
LIGHT SOURCE
- 4 BULBS REQUIRED (SOLD SEPARATELY)
BULB COMPARISON
TOOLS REQUIRED
PACKAGE CONTENTS
PART| DESCRIPTION| QUANTITY
| Stock Part#
---|---|---|---
A
| Crossbar Assembly| 1pc|
915739KIT
B
| Wire Connector| 3pcs
C
| Outlet Box Screw|
2pcs
D
| Quick Link Maillon rapide
|
2pcs
E
| Ceiling Canopy|
1pc
F
| Fixture Chain|
1pc
|
M381CHTMBK
G
| Fixture Loop|
1pc
|
N/A
H
| Socket Assembly|
1pc
I
| Large Ring|
1pc
J
| Ring|
1pc
Installation Instructions
If the ceiling canopy is not snug against the ceiling, remove it from the crossbar assembly. Adjust the length of the pre-assembled nipple by unscrewing the pre-assembled hex nut. Screw the nipple in or out of the crossbar until the correct length is achieved. Then, re-attach the ceiling canopy.
- A: Adjust fixture chain length.
- B: – C: Install fixture chain.
- A – Pull the supply wires and ground wire up through the fixture chain alternating links.
- B – Push the ends of the supply wires and ground wire up through the loop and into the outlet box.
- C – Remove the canopy.
- D – Insert the remaining slack wire into the outlet box.
- Trim excess fixture wire leaving a minimum of 6 inches hanging out of the outlet box.
- Separate the smooth side and ribbed side of the supply wire.
- Using wire strippers, strip each wire 1/2 inch from the end.
CARE AND MAINTENANCE
- Wipe clean using a soft, dry cloth or static duster.
- Always avoid using harsh chemicals and abrasives to clean fixtures as they may damage the finish.
TROUBLESHOOTING
PROBLEM
- The lights will not turn on.
- The fuse blows or the circuit breaker trips when the light is turned on.
POSSIBLE CAUSE
- The bulb is burned out.
- The power is off.
- Faulty wire connection.
- Faulty switch.
Crossed wires or power wires are grounding out.
CORRECTIVE ACTION
- Replace the light bulb.
- Make sure the power supply is on.
- Check wiring.
- Test or replace the switch.
Check the wire connection.
Thank you for purchasing this QUOIZEL product.
If you have any questions or problems, please call our customer service
department,
CONTACT
- 8:30 a.m. – 5:00 p.m., EST, Monday – Thursday, 10:20 a.m. – 5:00 p.m., EST, Friday.
- For the quickest response, please visit Quoizel.com and click on Contact Us.
- 1-844-564-3055
- E-mail:cs@quoizel.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>