QUOIZEL QFA5615MBK Four Light Fandelier Installation Guide
- October 30, 2023
- QUOIZEL
Table of Contents
QUOIZEL QFA5615MBK Four Light Fandelier
Released Date: 2022-04-14
Product Care and Maintenance
If you need further assistance call Quoizel Customer Care at 1-800-645-3184 (9:00am – 5:00pm EST), or visit us online at www.quoizel.com.
Product Package Contents
- Rod Assembly x1 (A)
- 12L Rod x1 (B)
- Receiver x 1 (E)
- LED Bulb x4 (H)
- Ceiling Canopy x1 (C)
- Ceiling D Canopy Cap x1
- Fan Blade x1 (F)
- Blade G Assembly Nut x1
- Fixture Body x1 (I)
Package Contents (Parts Bag 1)
-
Lock Washer x4 (AA)
-
Spring Washer x4 (BB)
-
Flat Washer x4 (CC)
-
Wire Connector x7 (DD) [1pc replacement connector
included] -
Screw x2 (EE)
-
Mechanical Screw x2 (FF)
-
Hanger Frame x1 (GG)
Package Contents (Parts Bag 2)
- Spring Washer x1 (HH)
- Flat Washer x1 (II)
- Screw x1 (KK)
- Wall Anchor x1 (JJ)
- Fastener with LL Set Screw x1
Package Contents (Parts Bag 3)
- 9V Battery x1 (NN)
- Remote Control MM Transmitter x1
- Wall Bracket OO x 1 (PP)
- Screw x2 (PP)
Product Installation
Step 1: Install Hanger Frame
- This fan cannot be used for the ceiling which angle is greater than 10 degree. For angled ceilings, point opening toward peak.
Step 2: Choose Rod
OPTION 1: Standard Downrod (Included Pre-assembled) for ceilings 11 Feet high. SKIP TO NEXT STEP.
OPTION 2: Longer Downrod (Included) for angled ceilings or ceilings 12 Feet or higher.
Step 3: Install Rod to Fixture Body
- Remove pin.
- Install ceiling canopy & ceiling canopy cap.
- Remove set screws on fixture body.
- Install set screws.
- Install pin.
- Install rod.
Step 4: Install Rod to Hanger Frame
- Pick the fan up by the down rod only. Place the downrod ball into the slot in the ceiling bracket.
Step 5: Install Safety Cable
_ Optional: _for concrete ceiling.
Step 6: Wiring
- White wire from outlet box
- Black wire from receiver with the Label AC N
- Black (or Red) wire from outlet box
- Black wire from receiver with the Label AC L
- Green Ground Screw on the Crossbar
- Bare, or Green Ground wire from outlet box
Step 7: Place Controller to Hanger Frame
ON ON DIP 1234
- White Wire from receiver with the Label N
- White wire from fixture identified with the Label N
- Black wire from receiver with the Label MOTOR L
- Blue wire from receiver with the Label LIGHT L
- Black wire from fixture identified with the Label MOTOR L
- Blue wire from fixture identified with the Label LIGHT L
- Ground wire from Fixture Ground wire from Hanger Frame
Step 9: Install Fan Blade
- Remove pin.
- Attach fan blade.
- Install pin.
- Install blade assembly nut.
Step 10: Install Bulbs
Install four correct bulbs referring to fixture markings and/or labels for maximum wattage.
Recommended Bulb Type (included): 8W MAX
Precautions
READ AND SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, install or operate the product.
WARNING
- RISK OF ELECTRIC SHOCK – Before beginning installation, turn off electricity at the circuit breaker box or the main fuse box.
- RISK OF FIRE – Use bulbs specified by the markings and/or labels on the fixture.
- RISK OF PERSONAL INJURY – DO NOT bend the blades when installing the fan, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
- RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY – mount to outlet box marked (acceptable for fan support of 22.7kg(50lbs) or less) and use mounting screws provided with the outlet box.
- All set screws must be checked, and re-tightened where necessary, before installation.
- After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and the ungrounded conductor on the other side of the outlet box.
- Suitable for use with solid-state speed controls.
- use only with light kits marked suitable for use in damp locations.
- This unit weighs 9.5 kg (20.9 lbs).
CAUTION
- For your safety, read the instructions completely before beginning installation.
- If in doubt about electrical installation, consult a licensed electrician.
- Disconnect fixture from the power source before replacing bulbs or cleaning. Make sure the bulbs are given sufficient time to cool be before removing.
TOOLS REQUIRED
CARE AND MAINTENANCE
- Wipe clean using soft, dry cloth or static duster. Always avoid using harsh chemicals and abrasives to clean fixture as they may damage the finish.
- If you need further assistance call Quoizel Customer Care at 1-800-645-3184 (9:00am – 5:00pm EST), or visit us on-line at www.quoizel.com.
PACKAGE CONTENTS
PACKAGE CONTENTS (PARTS BAG 1)
PACKAGE CONTENTS (PARTS BAG 2)
PACKAGE CONTENTS (PARTS BAG 3)
INSTALLATION
Install Hanger Frame
- This fan cannot be used for the ceiling which angle is greater than 10 degree.
- For angled ceilings, point opening toward peak.
Use machine screws
- When securing to existing ceiling fan-rated outlet box. that supports of 50 lbs (22.72 kg) or less.
Use wood screws
- When securing to support structure with approved electrical outlet box. Drill 9/64” pilot holes.
Choose Rod
Install Rod to Fixture Body
Install Rod to Hanger Frame
- Pick the fan up by the down rod only.
- Place the downrod ball into the slot in the ceiling bracket.
Install Safety Cable
Wiring
Place Controller to Hanger Frame
Install Ceiling Canopy and Cap
Install Fan Blade
Install Bulbs
- Install four correct bulbs referring to fixture markings and/or labels for maximum wattage.
Recommended Bulb Type (included):
Install Wall Bracket
Install Battery to Remote Control Transmitter
OPERATION
- Light button : Press it to turn on the lights. Press it again to turn off the lights. Long press it, the bulbs will be dimmable.
- HI, MED, LOW, OFF buttons: To adjust fan speed.
ADDITIONAL FUNCTIONS
Reverse Fan Blade (Optional)
Note
- If airflow is desired in the opposite direction, turn the fan off and wait for the blades to stop turning.
- Push the reverse switch to Left or Right completely.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>