GOLDEN LIGHTING 6085-LP Camden Linear Pendant Ceiling Light Instruction Manual
- June 17, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 6085-LP Camden Linear Pendant Ceiling Light
Specifications
- Model: 6085-LP BLK-NR
- Height: 8′
- Width: 30″
- Weight: 5.9 lbs
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island:
Center a linear pendant over the island. If hanging pendants, use one
pendant for every 24″ of the island. Fixtures should hang at least 30″ above
the countertop.
Pendants & Chandeliers Above a Dining Room Table:
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas:
The bottom should hang at least 7.5 feet from the floor. Allow clearance
for any opening doors.
Layered Lighting Tips:
To ensure the best lighting in your space, remember to layer your lighting
for both task and ambient lighting. Coordinate fixtures like sconces, flush
mounts, and pendants for a cohesive look. Install lights with dimmers for
customizable light levels.
Installation Instructions:
- Prepare for installation.
- Assemble the fixture according to provided instructions.
- Connect the wires following the wire identification guide.
- Finish the installation by pushing the canopy up to the ceiling and securing decorative nuts onto mounting screws.
- Install light bulbs according to specifications without exceeding the maximum wattage.
- Test the fixture by turning on the power.
Thank You for Choosing Golden Lighting for Your Lighting Needs!
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Love your light and want to show it off? Follow us, share a picture, and tag us on Social…
How to Identify the Fixture’s Wires
- Hot : Smooth, Black, or Transparent with Black Inner Thread
- Neutral : Ribbed, White or Transparent with White Inner Thread
- Ground : Copper, Bare Metal, Green, or Transparent Inner Thread
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by an accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. From the parts bag remove the mounting strap assembly.
Mounting strap (B) contains threaded holes. Two sets of mounting screws (A &
D) should be attached to the mounting strap (B). You may need to tighten nuts
(C) that hold mounting screws (A) in place. Place mounting strap (B) over the
junction box so that mounting screws (A) are vertical, and in alignment with
the hole locations on the fixture’s canopy (F). Pull house wires through the
center of the mounting strap (B). Secure mounting strap (B) to the junction
box with mounting screws (D) and a screwdriver. Tighten the screws securely.
ASSEMBLING THE FIXTURE
Measure to determine the correct number of rods (L) needed for proper hanging
height. There are three 12-inch rods and one 6-inch rod included for each side
of the fixture. To shorten the fixture, slide the desired number of excess
rods off. To lengthen the fixture, add additional rods. If additional rods are
needed, please contact the place of purchase to order more. Feed the fixture
wires from posts (M) through the rods (L). 3. Feed the fixture wires through
the swivel posts (K) and through the top of the canopy (F), iron sheet (I),
washers (H), and hex nuts (G). Thread the bottom rods onto posts (M) at the
top of the fixture’s body. Thread rods (L) together and pull the wires until
taut. Twist the top rods (L) onto the threads of swivel posts (K) of the
canopy (F). Place the iron sheet (I) onto canopy (F) and align the holes.
Secure swivel posts (K) to canopy (F) by tightening hex nuts (G) over washers
(H). Trim the wires to the desired length plus 8 to 10 inches.
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring.
Refer to the wiring diagram and attach the fixture’s wires to the power supply
wires from the junction box. Attach the fixture’s wires to the power supply
wires from the junction box. Connect Hot to Hot (transparent wire with black
inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with
white inner thread, white, or ribbed wire), and Ground to Ground (transparent
wire with green inner thread, green wire, or copper). Twist the ends of the
wire pairs together, and then twist on a wire connector. Make sure all twists
are in the same direction. If there is no house ground wire coming from the
junction box, locate ground screw (E) on the mounting bracket/mounting strap
and wrap the fixture’s ground wire around the ground screw. Use a screwdriver
to tighten the top of ground screw (E) onto the wires and into the mounting
bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
Push the canopy (F) up to the ceiling and tightly thread decorative nuts (J)
onto the exposed threads of mounting screws (A). Install light bulbs (not
provided) in accordance with the fixture’s specifications. Do not exceed the
maximum recommended wattage. Your installation is complete. Turn on the power
and test the fixture.
FAQ
How do I identify the fixture’s wires?
The fixture wires are labeled as Hot, Neutral, and Ground. Match these with
the corresponding house wires labeled with similar names. The ground wire is
typically copper, bare metal, green, or transparent inner thread.
Where can I find replacement parts or customer service?
Contact the place of purchase for replacement parts or customer service
inquiries.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>