MADSTAD ENGINEERING Honda NC750X Adjustable Windshield System

Please read this entire manual before proceeding with installation.

What is in the box

(1) Set of preassembled MadStad adjustable windshield brackets
(2) Nut plates (elbow shaped, silver)
(2) Plastic ribbed push-rivets
(2) M5 rubber well nuts

(2) M5 x 20 Phillips screws
(2) M5 metal flat washers
(4) M6 x 25 button socket screws
(4) M6 flat washers
(4) M6 split lock washers
(2) Side deflectors (plastic)
(2) Side deflector brackets
(4) M6 x 16 button socket screws
(4) M6 plastic flat washers
(4) M6 nylock nuts

For mounting the windshield:

(4) M5 truss screws (Phillips)
(4) black plastic flat washers
(4) 1/8” thick rubber washers

Tools Needed

• 4 mm Allen wrench (hex key)
• 10 mm wrench (open-end, box, or small adjustable crescent)

• 2 Phillips screwdriver

STEP 1

Remove your factory windshield; it is not adaptable for use with these brackets.

STEP 2

Remove the plastic plates and rubber well nuts that the factory windshield was attached to. The plastic pieces will pull up toward the front out of their holes, and the rubber well nuts must be pushed/pulled out from behind.

STEP 3

Install the nut plates and new well nuts as per the diagram at below:

A. Insert the M5 well nut down into the upper hole.
B. Set the nut plate behind the factory holes (red outline) with the flat side facing up (forward), and while holding it there push the plastic rivet through the center hole of the nut plate (second factory hole from the bottom).
C. You should be able to see the threaded inserts through the remaining two holes.

STEP 4

Next, you are going to attach the MadStad windshield brackets to the bike starting with the M5 x 20 screws and flat washer. (See throttle-side diagram below.) Slip an M5 metal flat washer onto the M5 x 20 Phillips screw, lay the bracket over the factory holes and insert the screw into the top hole (into the rubber well nut). Tighten until snug (do not overtighten). If you are not i nstalling the side deflectors you can go ahead and screw in the M6 x 25 screws into the other two holes as shown below, with a lock washer and flat washer on each. DO NOT use power tools to drive in these screws; hand tools only.

STEP 5

If you are installing the side deflector brackets then windshield bracket installation is the same as in Step 4, except that you must first lay the side deflector bracket over the windshield bracket as shown below, then insert the M6 x 25 screws with washers and tighten. (Clutch-side image below.) You may want to pre-install the plastic deflector onto the metal deflector bracket before fastening it to the bike, but it is not required. See the next section on Deflector Assembly.

Side Deflectors

Your kit came with two acrylic side deflectors and deflector mounting brackets that attach to the front of the bike at the windshield bracket screws. They are angled back toward the rider and block lower airflow for a smoother and quieter ride. You can pre-assemble the deflector onto its bracket prior to attaching to the bike using the M6 x 16 screws with washers and lock nuts as shown below.



Clutch (left) side deflector as seen from the front of the bike.

Windshield Installation

1. Pre-install the Truss screws & washers into the windshield holes as shown in the image below.
2. Once all four of the screws are in place, gently guide the screws into the Well Nuts in the brackets until all four are set.
3. Hand tighten the Truss screws until they swell up behind the bracket and are firmly holding the windshield.

• Windshield Layout:
  

• Well Nut Tips
  
  

Disclaimer

Neither MadStad Engineering nor its owners shall be liable for any damages, consequential or inconsequential, resulting from the use of our products. Installation of any of our products constitutes acceptance of these terms.
It is the responsibility of the user to make sure all fasteners are tightened securely, the windshield is mounted properly and the adjustment knobs are tightened snugly before putting the motorcycle in motion. MadStad systems ARE NOT intended to be adjusted while the vehicle is in motion; you must pull over out of the way of traffic and come to a complete stop before making any changes. The user must never place the windshield in such a position as to interfere with the safe and complete movement of the handlebars and controls.

Returns and Warranty

MadStad adjustable brackets carry a lifetime warranty against manufacturing defects. This does not include cosmetic issues nor any parts that inherently wear out or degrade over time such as rubber and plastic parts. Windshields, deflectors, and other similar plastic parts are warrantied for 1 year against manufacturing defects, not against cosmetic issues or issues related to normal wear and tear. Please visit our website for further details.

Customer Support

MadStad Engineering, Inc.
1451 E. Jefferson Street
Brooksville, FL 34601 U.S.A.
Phone: 352-848-3646
Fax: 352-240-3911
Web Site: http://www.madstad.com
Email: support@madstad.com
Thank you for your support, and ride safely!
April 24,

References

• Adjustable motorcycle windshield systems | motorcycle windscreen | Madstad
• Adjustable motorcycle windshield systems | motorcycle windscreen | Madstad

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>