SIGNATURE HARDWARE 946291-KE Griggs Solid Brass Full Plate Instruction Manual

SIGNATURE HARDWARE 946291-KE Griggs Solid Brass Full Plate

Product Information

Specifications:

• Brand: Griggs
• Product Name: Entry Door Set
• SKU: 946291-KE, 946279-KE, 946279-DU, 946290-KE-LH, 946291-DU, 946290-KE-RH, 946278-KE-RH, 946290-DU, 946278-KE-LH, 946278-DU
• Minimum Door Thickness: 1-3/4″ (44mm)
• Maximum Door Thickness: 2″ (50mm)
• Backset Compatibility: 2-3/8″ and 2-3/4″
• Bore Hole CTC Distance: 5 1/2″
• Bore Hole Size: 2 1/8″
• Cross Bore Size: 1″

Product Usage Instructions

Before You Begin
We recommend consulting a professional if you are unfamiliar with installing door hardware. Ensure that the door thickness is within the specified range.

Getting Started

1. Ensure you have all the required materials for installation.
2. Observe local building codes.
3. Unpack and inspect the product for any shipping damage. Contact Customer Relations if damage is found.

Installation Steps:

1. Confirm your door has 2 bore holes drilled into it.
2. Check that your deadbolt and passage latch match the backset (2-3/8″ or 2-3/4″).
3. Use safety glasses when working.
4. Use a wood chisel for any necessary adjustments.
5. Use a drill and Phillips screwdriver for installation.

FAQ

• Q: What should I do if my door thickness is not within the specified range?
  A: If your door thickness does not fall within the specified range, consult a professional for guidance on modifying the door or selecting a compatible product.

• Q: How can I ensure the proper alignment of the door set components?
  A: Double-check the bore hole sizes and backset compatibility of the deadbolt and passage latch to ensure proper alignment during installation.

GRIGGS
ENTRY DOOR SET
JUEGO DE PUERTA DE ENTRADA
ENSEMBLE PORTE D’ENTREE
SKU: 946291-KE, 946279-KE, 946279-DU, 946290-KE-LH, 946291-DU, 946290-KE-RH, 946278-KE-RH, 946290-DU,
946278-KE-LH, 946278-DU

BEFORE YOU BEGIN

We recommend consulting a professional if you are unfamiliar with installing door hardware. Signature Hardware accepts no liability for any damage to the door, hardware, or for personal injury during
installation.
Observe all local building codes.
Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer Relations team via live chat at www.signaturehard- ware.com or by emailing support@signaturehardware.com.

GETTING STARTED
Ensure that you have gathered all the required materials that are needed for the installation. NOTE: This doorset works on a minimum door thickness of 1-3/4” (44mm) and maximum door thickness of 2” (50mm)

HARDWARE INCLUDED

Passage Latch Kit

INCLUDED

TOOLS AND MATERIALS:

INSTALLATION

1. Confirm that your door has 2 bore holes drilled into the door. This doorset works for both 2-3/8” and 2-3/4” backsets. Please check that your deadbolt and passage latch match the backset.

   • Bore Hole CTC distance: 5 1/2”
   • Bore Hole Size: 2 1/8”
   • Cross Bore Size: 1”

2. Drill a third, 15mm diameter hole located 2-1/4 inches (center to center) below the bottom bore hole

3. Insert the passage and deadbolt latch into the appropriate cross bore on the edge of the door using the supplied screws. The passage latch inserts into the bottom hole and the deadbolt latch into the upper hole.
   Do not tighten screws until installation is complete.

4. Insert the lock housing into the exterior escutcheon plate. Mount the exterior escutcheon plate to the exterior side of the door.

5. Add the interior escutcheon plate to the interior side of the door. The interior assembly and exterior assembly should fit into the deadbolt latch and passage latch.

6. Secure both escutcheon plates together and to the door by ?rst installing the two Lock Housing screws. These two screws insert through the interior escutcheon on either side of the thumb latch and fasten back into the lock housing.

7. Install post screw on interior escutcheon plate.

8. Before installing screws you will need to predrill holes into the door. Install screws into door through exterior escutcheon plate using the appropriate hardware. Tighten all fasteners, including screws through dead bolt and latch bolt on side edge of door.

DUMMY INSTALLATION

1. Place dummy door knob hardware in location and mark mounting holes with pencil.
2. Drill pilot holes at marked locations.
3. Secure dummy knob to door using provided mounting hardware.

1.855.715.1800 signaturehardware.com

References

• ware
• Signature Hardware - Shop Unique, Quality Decor

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>