ELATEC TWN4 MultiTech 2 LEGIC LF HF User Manual

ELATEC TWN4 MultiTech 2 LEGIC LF HF

Product Information

Specifications

• Product Name: TWN4 MULTITECH 2 LEGIC LF HF
• Key Features: Powerful SDK for writing apps, firmware upgrade in the field, direct chip-commands support
• RFID Technologies: Reads more than 60 RFID technologies from low (LF) and high frequency (HF) bands, including NFC
• Intended Use: Indoor use only

Frequently Asked Questions

• Q: Can the TWN4 MultiTech 2 LEGIC LF HF be used outdoors?
  • A: No, the product is intended for indoor use only. Using it outdoors may result in improper functionality.
• Q: How can I upgrade the firmware of the TWN4 MultiTech 2 LEGIC LF HF?
  • A: The product supports field firmware upgrades. Refer to the user manual for detailed instructions on upgrading the firmware.

INTRODUCTION

ABOUT THIS MANUAL

This user manual is intended for the user and enables a safe and appropriate handling of the product. It gives a general overview, as well as important technical data and safety information about the product. Before using the product, the user should read and understand the content of this user manual. For the sake of better understanding and readability, this user manual might contain exemplary pictures, drawings and other illustrations. Depending on your product configuration, these pictures might differ from the actual design of your product.

The original version of this user manual has been written in English. Wherever the user manual is available in another language, it is considered as a translation of the original document for information purposes only. In case of discrepancy, the original version in English will prevail.

SCOPE OF DELIVERY

Depending on your product configuration, the product can be delivered alone or with different components and accessories, such as cables or wall holders, as part of a kit. For more information about the delivered components and accessories, refer to your delivery note, consult the ELATEC website or contact ELATEC.

ELATEC SUPPORT

• In case of any technical questions or product malfunction, refer to the ELATEC website (www.elatec.com) or contact ELATEC technical support at support-rfid@elatec.com
• In case of questions regarding your product order, contact your Sales representative or ELATEC customer service at info-rfid@elatec.com

INTENDED USE

• The contactless RFID readers and modules of the ELATEC TWN4 MultiTech 2 LEGIC family are a direct enhancement of the TWN4 MultiTech LEGIC readers with the same form factors (PCB modules and desktop readers with housing).
• During the development of the TWN4 MultiTech 2 LEGIC family, special emphasis has been placed on optimizing the HF performance (13.56 MHz). Compared to the predecessor TWN4 MultiTech LEGIC, the read range could be increased by more than 50% for LEGIC transponders and even doubled for some HF transponders.
• TWN4 MultiTech 2 LEGIC LF HF key features include a powerful SDK for writing apps that are executed directly on the reader, the possibility to upgrade the firmware in the field and a direct chip-commands support. Additionally, the reader can simultaneously read more than 60 RFID technologies from low (LF) and high frequency (HF) bands, including NFC. This gives the option to select as many of the technologies required instead of being forced to select just a few ones.
• The product is for indoor use and may not be used outdoor.
• Any use other than the intended use described in this section, as well as any failure to comply with the safety information given in this document, is considered improper use. ELATEC excludes any liability in case of improper use or faulty product installation.

SAFETY INFORMATION

Transport and storage

• Observe carefully the transport and storage conditions described on the product packaging or other relevant product documents (e.g. data sheet).

Unpacking and installation

• Before unpacking and installing the product, this user manual and all relevant installation instructions must be read and understood carefully.
• The product is equipped with a cable.
  • Do not twist or pull the cable.
  • Do not replace the cable and do not use a cable extension.

ELATEC excludes any liability for damages or injuries resulting from the use of the product with a cable extension or a replaced cable.

Handling

• Depending on your product configuration, the product might be equipped with one or more light-emitting diodes (LED). Avoid direct eye contact with the blinking or steady light of the light-emitting diodes.
• The product has been designed for a use under specific conditions, e.g. in a specific temperature range (refer to the product data sheet). Any use of the product under different conditions might damage the product or alter its reading performance.
• The use of other RFID readers or reader modules in direct vicinity to the product, or in combination with the product might damage the product or alter its reading performance. In case of doubts, contact ELATEC for more information.
• The user is liable for the use of spare parts or accessories other than the ones sold or recommended by ELATEC. ELATEC excludes any liability for damages or injuries resulting from the use of spare parts or accessories other than the ones sold or recommended by ELATEC.
• Like most electronic devices, RFID systems generate electromagnetic waves that can vary in amplitude and frequency. It is generally known and accepted that some RFID devices might potentially interfere with personal medical devices, like pacemakers or hearing aids. TWN4 MultiTech 2 LEGIC LF HF fulfills general radio and EMC requirements. However, users with a pacemaker or any other medical device should use TWN4 MultiTech 2 LEGIC LF HF carefully and refer to the information given by the manufacturer of their medical devices before using TWN4 MultiTech 2 LEGIC LF HF or any host device containing TWN4 MultiTech 2 LEGIC LF HF.

Maintenance and cleaning

• Any repair or maintenance work should be done by a trained and qualified personnel only.
  • Do not try to repair or carry out any maintenance work on the product by yourself.
  • Do not allow any repair or maintenance work on the product by an unqualified or unauthorized third party.
• The product does not need any special cleaning. However, the housing may be carefully cleaned up with a soft, dry cloth and a non-aggressive or non-halogenated cleaning agent on the outer surface only.
  • Make sure that the used cloth and cleaning agent do not damage the product or its components (e.g. label(s)).

Disposal

• The product must be disposed of in accordance with the EU directive on waste electrical and electronic equipment (WEEE) or any applicable local regulations.

Product modifications

• The product has been designed, manufactured and certified as defined by ELATEC.
• Any product modification without prior written approval from ELATEC is prohibited and considered improper use of the product. Unauthorized product modifications may also result in the loss of product certifications.

If you are unsure about any part of the safety information above, contact ELATEC support.
Any failure to comply with the safety information given in this document is considered improper use. ELATEC excludes any liability in case of improper use or faulty product installation.

TECHNICAL DATA

TECHNICAL SPECIFICATIONS

Color: black or white

DIMENSIONS (L X W X H)| Approx. 88.00 x 56.00 x 18.50 mm / 3.46 x 2.20 x 0.73 inch

POWER

| USB: 4.3 V – 5.5 V

RS-232: requires 5 V external power supply

PS2 classified power source according to IEC 62368-1, short-circuit current < 8 A

CURRENT CONSUMPTION| RF field on: 140 mA typically
TEMPERATURE RANGE| Operating: -25 °C up to +70 °C (-13 °F up to +158 °F)

Storage: -40 °C up to +75 °C (-40 °F up to +167 °F)

RELATIVE HUMIDITY| 5% to 95% non-condensing
READ/WRITE DISTANCE| LF and HF: up to 100 mm / 4 inch, depending on environment and transponder
WEIGHT| Approx. 120 g / 4.23 oz (with cable)

FIRMWARE

The product is delivered ex-works with a specific firmware version. Refer to the label attached to the product to find the firmware version installed ex- works.

ANTENNAS

The reader is equipped with the following antennas:

• HF antenna: (13.56 MHz)
  • Dimensions: 42 x 47 mm / 1.65 x 1.85 inch
  • Number of turns: 3
• LF antenna: (125 kHz)
  • Diameter: 16 mm / 0.63 inch
  • Number of turns: 120

For more information, refer to the related product data sheet or other technical documents.

MODE OF OPERATION

The mode of operation described in the following chapter is based on a standard ELATEC RFID reader equipped with two LEDs. Depending on your product (number of LEDs, installed firmware, etc.) and in case the product settings have been modified with the AppBlaster tool, the information below might differ from your product configuration when in operation. In particular, the color and sequence of the LEDs on your product might be different.

OPERATING MODE

• In order to start operating TWN4 MultiTech 2 LEGIC LF HF, it simply has to be connected directly to a host device.

POWER UP

Once TWN4 MultiTech 2 LEGIC LF HF is connected to the host device, it detects the type of communications cable (e.g. USB or RS-232), with which it is connected to the host.

In case of RS-232:

• A version string is sent via RS-232 to the host device.
• A 5 V external power supply is required and must meet the following conditions:
  • PS2 classified power source according to IEC 62368-1
  • Short-circuit current < 8 A

ENUMERATION

This is only applicable for the USB version: Once the device has been powered up, it is waiting for completion of the enumeration by the USB host. As long as the device is not enumerated, it is entering a minimum power consumption mode, where both LEDs are turned off.

INITIALIZATION

After powering up and enumeration (in USB mode), the device is turning on the built-in transponder reader logic. The green LED is turned on permanently. Some RFID readers need some kind of initialization, which is performed in this step. After successful initialization, the device sounds a short sequence, which consists of a lower tone followed by a higher tone.

NORMAL OPERATION

• As soon as the reader has completed the initialization, it is entering normal operation.
• During normal operation, the reader is searching for a transponder continuously.

DETECTION OF A TRANSPONDER

If a transponder is detected by the reader, following actions are performed:

• Send the ID to the host. By default, the USB device sends by emulating keystrokes of a keyboard. An RS-232 device sends the ASCII code of an ID.
• Sound a beep.
• Turn off the green LED.
• Blink the red LED for two seconds.
• Turn on the green LED.

Within the two seconds timeout, where the red LED is blinking, the transponder, which just has been recognized will not be accepted again. This prevents the reader from sending identical IDs more than one time to the host.
If during the two seconds timeout of the red LED a different transponder is detected, the complete sequence restarts immediately.

SUSPEND MODE

The USB version of the reader supports the USB suspend mode. If the USB host is signaling suspend via the USB bus, the reader is turning off most of its power consuming peripherals. During this operation mode, no detection of transponders is possible and all LEDs are turned off. Once the host is resuming to normal operation mode, this is also signaled via the USB bus. Therefore, the reader will resume to normal operation too.

FCC STATEMENT

COMPLIANCE STATEMENTS

EU

Hereby, ELATEC GmbH declares that TWN4 MultiTech 2 LEGIC LF HF is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: elatec.com/approvals

FCC

Contains FCC ID: WP5TWN4F22

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation. (except receivers associated with operation of a licensed radio service and stand-alone devices).

Caution

The Federal Communications Commission (FCC) warns the users that changes or modifications to the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC §15.105 (b)

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

ISED CANADA

Contains IC: 7948A-TWN4F22

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

RF EXPOSURE COMPLIANCE

RF exposure statement (mobile and fixed devices)
This device complies with the RF exposure requirements for mobile and fixed devices. However, the device shall be used in such a manner that the potential for human contact during normal operation is minimized.

CHINA (PRC)

Micropower scope of use declaration:

TWN4 MultiTech 2 LEGIC LF HF supports transmission frequencies of 13.56 MHz and 125 kHz. The user needs to adhere to the following specifications when using the product:

1. The specific provisions listed in the “catalog and the technical specifications for micropower short-range radio transmission equipment” as well as the usage scenarios for the antenna type used, the functions, and the customary use of the control system, regulation, and switches must be complied with;

   • Transmission power:

   • 13.56 MHz: ≤ -9.06 dBμA/m
     (field strength at 10 meters, standard max value)

   • 125 kHz: ≤ -20.04 dBμA/m
     (field strength at 10 meters, standard max value)

   • Antenna: built-in antenna (cannot be removed)

   • Control system, regulation, and switches: The user cannot control, regulate, or switch over the radio transmission function of the antenna.

2. The unauthorized modification of usage scenarios or the conditions of use, expansion of the transmission frequency range, or increase of the transmission power (including installing additional transmission power amplifiers), as well as the unauthorized modification of the transmission antenna are not allowed;

3. The product may not interfere in any way with any legal radio transmitters (stations) and may not offer any shielding from harmful interference;

4. The product must be able to tolerate interference caused by industrial, scientific, and medical (ISM) devices which radiate high frequency energy or other legal interference from radio transmitters (stations);

5. Should the product cause harmful interference on other legal radio transmitters (stations), product use must be discontinued immediately and suitable measures must be taken prior to using the product again in order to eliminate said interference;

6. When using micropower devices inside of an aircraft or radiometric observatories, or when using such devices in meteorological radar stations, satellite ground stations (including measuring and control stations, distance measuring stations, receiving stations, or navigation stations), as well as in radio transmitters (stations) used by the military and electromagnetic environment protections zones at airports, all applicable provisions of the competent authorities as well as statutory provisions, national regulations, and national standards must be complied with;

7. Remote controls of any kind may not be used within 5000 meters of airport runways, measured from the middle of the runway;

8. Ambient conditions such as temperature and voltage when using micropower devices:

   • operating voltage of TWN4 MultiTech 2 LEGIC LF HF: 4.3 V – 5.5 V (charging via USB),
   • operating temperature: -25 °C – +70 °C,
   • storage temperature: -40 °C – +75 °C.

The user must strictly adhere to these temperature and voltage specifications when using the product.

SINGAPORE

• Complies with IMDA Standard
• [DA 103787]

UNITED KINGDOM

TWN4 MultiTech 2 LEGIC LF HF complies with the requirements of the UK legislations and other regulations as listed in the respective UK declaration of conformity. The importer is responsible for applying the following information to the packaging of the product:

• the importer company’s details, including the company’s name and a contact address in the United Kingdom.
• UKCA marking

APPENDIX

A – RELEVANT DOCUMENTATION

ELATEC documentation

• ELATEC quick start guide
• TWN4 MultiTech 2 LEGIC LF HF data sheet
• TWN4 MultiTech 2 LEGIC LF HF functional description
• TWN4 MultiTech 2 technical handbook

B – TERMS AND ABBREVIATIONS

Refers to Directive 2012/19/EU of the European Parliament and of the Council of the European Union

C – REVISION HISTORY

“Technical Data”, “Mode of

Operation” and “Compliance Statements” updated

| 07/2023
05| Chapters “Technical Data” and “Compliance Statements” updated| 03/2023
04| Chapter “Compliance Statements” updated| 02/2023
03| Chapter “Compliance Statements” updated| 12/2022
02| Chapter “Technical Data” updated| 07/2022
01| First edition| 06/2022

Contacts

EMEA

• Puchheim, Germany
• +49 89 552 9961 0
• sales-rfid@elatec.com

AMERICAS

• Palm City, Florida, USA
• +1 772 210 2263
• americas-info@elatec.com

ASIA

• Shenzhen, China
• +86 755 23946014
• apac-info@elatec.com

JAPAN

• Tokyo, Japan
• +81 90 1846 6900
• japan-info@elatec.com

elatec.com

Elatec reserves the right to change any information or data in this document without prior notice. Elatec declines all responsibility for the use of this product with any other specification but the one mentioned above. Any additional requirement for a specific customer application has to be validated by the customer himself at his own responsibility. Where application information is given, it is only advisory and does not form part of the specification.

Disclaimer: All names used in this document are registered trademarks of their respective owners.

© 2023 ELATEC GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>