SECO-LARM IP 5MP 2.8mm Bullet Camera with WDR Instructions

: June 9, 2024
: SECO-LARM

SECO-LARM IP 5MP 2.8mm Bullet Camera with WDR

Product Information: IP 5MP 2.8mm Bullet Camera with WDR

The IP 5MP 2.8mm Bullet Camera with WDR (EV-N1506-2W4WQ) is a high-resolution camera that is designed for use in outdoor environments. The camera features advanced AI functions and supports H.265/H.264/MJPEG video encoding. The camera also includes a Micro SD card slot and a reset button.

Features

AI Functions
SmartSens CMOS Sensor
5MP Resolution
Supports H.265/H.264/MJPEG Video Encoding
WDR (Wide Dynamic Range)
Back Light Compensation
2DNR (Digital Noise Reduction)
3DNR (Digital Noise Reduction)
Micro SD Card Slot
Reset Button

Specifications

Type: Bullet Camera
Sensor: 1/2.7 SmartSens CMOS
Video Encoding: H.265/H.264/MJPEG
Megapixels: 5MP
Resolution: 2880×1620
Backlight: Disable (Default), Back Light, HLC, WDR
AI Functions
of IR LEDs: 2
Lens: 2.8mm
Viewing Angle: 515/16 (151mm)
Minimum Illumination:
F Stop:
Gamma Correction:
S/N Ratio:
Gain Control:
White Balance:
Operating Voltage:
Current Draw (IR Off):
IP Rating:
Operating Temperature:
Dimensions:
Weight:
On-board Storage:

Parts List

1x Camera
1x Manual
2x Hex Key
1x Mounting Template
3x Mounting Screws
1x Weatherproof Connector

Before Starting

Please read this manual carefully and keep it for future reference.
Use the camera within the given temperature and electrical limits.
Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.

Product Usage Instructions

Installation:

Run a 12VDC power supply wire and cable with an RJ45 jack through the wall at the location where the camera is to be mounted. The 12VDC power supply wire is not required if using PoE.
Install and Execute the Device Config Tool on a computer connected to the same network as the camera.
Press the Search button. This will search for IP cameras connected to the same router on the network. It may take several seconds to complete. Default IP address is 192.168.1.168.
Once the search is complete, click on the camera IP or type the IP address manually using Internet Explorer.
IP Address: The camera may use Dynamic or Static IP addressing. An example of a typical static IP setting is as follows: IP Address: 192.168.0.10 (you can change the last column)

Camera Angle and Positioning

To adjust the camera angle and positioning, loosen the camera angle adjustment screw and mounting arm adjustment screw. Rotate the camera and position the mounting arm in the desired position and retighten the screws.

Troubleshooting

The screen is blank
The screen image is dim
The screen image has poor contrast
The screen image flickers
The screen image is distorted
The camera case is hot

Note: For the full Web Admin manual, download it from the camera’s product page on www.seco-larm.com.

FCC COMPLIANCE STATEMENT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.

Features

1/2.7″ 5MP SmartSens CMOS sensor
30FPS@5MP (2880×1620)
2.8mm Lens
Tri-stream encoding:
H. 265, H.264, and MJPEG
True Wide Dynamic Range (WDR)
Digital Noise Reduction (3DNR)
True Day & Night function with ICR module
ICR Sensitivity adjustment
Corridor mode
IP66 Weatherproof
IR Range 98′ (30m)
Smart IRs adjust IR strength to conditions
MicroSD slot (512GB max)
PoE (IEEE802.3af), 12VDC
ONVIF® Profile G, S, and T conformant
Operating Temperature: -40°~131°F (-40°~55°C)

AI Functions

Human and Vehicle Detection
Perimeter Intrusion Detection
Line Crossing Detection
Stationary Object Detection
Cross Counting
Heat Map
Crowd Density Detection
Queue Length Detection
Face Detection

For the full Web Administration manual, download from the camera’s product page on www.seco-larm.com.

Parts List

1x Camera
2x Hex Key
3x Mounting Screws
1x Manual
1x Mounting Template
1x Weatherproof Connector

Specifications

Type	Bullet camera
Sensor	1/2.7” 5MP SmartSens CMOS
Video encoding	H.265/H.264/MJPEG
Megapixels	5MP
Resolution	2880×1620
Backlight	Disable (Default), Back Light, HLC, WDR
DNR	2DNR
3DNR	Yes

__

AI functions

| Human and Vehicle Detection, Perimeter Intrusion Detection, Line Crossing Detection, Stationary Object Detection, Cross Counting, Heat Map, Crowd Density Detection,

Queue Length Detection, Face Detection

Overview

IMPORTANT NOTES

Do not cut DC jack or RJ45 jack as warranty will be voided.
Do not open camera case, no serviceable parts.

Before Starting

Please read this manual carefully and keep it for future reference.
Use the camera within given temperature and electrical limits.
Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.
Do not point the camera at the sun. Heat could damage the camera, even when not in use.
Do not open or disassemble the camera. There are no field-serviceable parts inside.
Do not drop the camera or subject it to strong vibrations.

Installation

Run a 12VDC power supply wire and cable with an RJ45 jack through the wall at the location where the camera is to be mounted. The 12VDC power supply wire is not required if using PoE.
Install and Execute “Device Config Tool” on a computer connected to the same network as the camera.
Press the “Search” button. This will search for IP cameras connected to the same router on the network. It may take several seconds to complete. Default IP address is 192.168.1.168.
Once the search is complete, click on the camera IP or type the IP address manually using Internet Explorer.
IP Address: The camera may use Dynamic or Static IP addressing. An example of a typical static IP setting is as follows:
IP Address: 192.168.0.10 (you can change the last column)
Netmask: 255.255.255.0
Gateway : 192.168.0.1
DNS1/2: You can copy the PC’s network properties. This is for an internet environment.
Input “admin” for user ID and password. If this is the user’s first time logging into the camera, the user will be prompted for a new password.
NOTE: If the password is unknown, hold the RESET button located on the camera for about 10 seconds and reload “Device Config Tool”.
In order to access the camera web interface, the user will be prompted to download and install the Active-X web plugin.
Once installed, the user will be able to view live camera video and modify necessary configurations.
NOTE: For the full Web Admin manual, download from the camera’s product page on www.seco-larm.com.

Camera Angle and Positioning

To adjust the camera angle and positioning, loosen the camera angle adjustment screw and mounting arm adjustment screw. Rotate the camera and position the mounting arm in the desired position and retighten the screws.

Troubleshooting

The screen is blank
- Check that the camera is powered up.
- Check that the power supply’s polarity is correct.
- Check that the monitor is powered up.
- Check that the video cable connecting the camera to the monitor is connected properly.
The screen image is dim
- Clean the lens using a soft, clean cloth.
- Check that the light source is adequate.
The screen image has poor contrast
- Adjust the monitor’s contrast knob.
- Change the position of the camera.
The screen image flickers
- Change the position of the camera.
The screen image is distorted
- Change the position of the camera.
The camera case is hot
- Check that the correct power supply is in use.

FCC COMPLIANCE STATEMENT

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO- LARM will not be held responsible for the use of this product in violation of any current laws or statutes.

IMPORTANT: Users and installers of this product are responsible for ensuring that the installation and configuration of this product complies with all national, state, and local laws and codes. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.

California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason, SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.

NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners.
Copyright © 2023 SECO-LARM U.S.A., Inc. All rights reserved.

Website : www.seco-larm.com
Phone: 949-261-2999 | 800-662-0800
Email: sales@seco-larm.com