TESLA TLAN001 Diagnostic Adapter Cables User Guide

TESLA TLAN001 Diagnostic Adapter Cables

Product Information

Product Specifications

• Model: Tesla Diagnostic Adapter Cables
• Supported Models: Model S & Model X
• Packing List:
  • TLAN001
  • TCAN001
  • TCAN002
  • Tesla Diagnostic Adapter Cables Connection Guide (This Document)

Frequently Asked Questions

• Q: What are the supported models for Tesla Diagnostic Adapter Cables?
  • A: The supported models are Model S and Model X.
• Q: What tools are required for disassembly?
  • A: You will need a Torx T20 socket, a plastic crowbar with a 10mm deep socket, and knowledge of X437, X861, and X863 locations after September 2015.
• Q: How should I prepare before disassembling?
  • A: Make sure that the vehicle power is off before starting disassembly. Additionally, disconnect the negative cable of the 12V battery at the front compartment and the first responder loop on the right side of the 12V auxiliary battery.

Product Usage Instructions

Preparation Before Disassembly:

Warning: Be sure that vehicle power is off before disassembling.

1. Disconnect the negative cable of the 12V battery at the front compartment.
2. Disconnect the first responder loop on the right side of the 12V auxiliary battery.

Disassembly Steps:

1. Remove the side cover of the instrument panel from the vehicle, and then remove the screws behind the side cover.
2. Remove the lower dash trim from the vehicle.
3. Remove the gasket on the top of the instrument cluster.
4. Remove the fixing screws (2 pcs) between the top pad and the instrument panel carrier (torque 1.2 Nm).
5. Release the fixing clips (2 pcs) between the steering column cover and the instrument cluster frame.
6. Remove the instrument cluster frame from the vehicle.
7. Remove both the outer face-level vent and the inner face-level vent from the vehicle dash.
8. Remove the instrument cluster from the instrument panel carrier to check the harness connection.
9. Disconnect the X861 from the backside of the instrument cluster.
10. Connect the diagnostic cable TLAN001 to the instrument cluster connector X861.

Packing List

Adapter Cable| Supported Model| Model Year| Connection Port| Connection Port Location| Function
---|---|---|---|---|---

TLAN001

| Model S/Model X| All| X861| On the back of the instrument cluster| Activate Factory Mode
After Sept 2015|

X863

| Below the central control screen| Perform diagnosis for LAN related systems
Before Sept 2015| On the left side of the instrument cluster
TCAN001| After Sept 2015| X437| Below the central control screen| Perform diagnosis for CAN related systems
TCAN002| Before Sept 2015

TLAN001 Connection Guide

Required Tools (not included):

Preparation Before Disassembly

Warning: Be sure that vehicle power is off before disassembling.

1. Tap the lower-left corner of the central control screen in the following sequence: vehicle icon → Safety & Security → POWER OFF.
2. Disconnect the negative cable of the 12V battery at the front compartment.
3. Disconnect the first responder loop on the right side of the 12V auxiliary battery.

Disassembly Steps

1. Remove the side cover of the instrument panel from the vehicle, and then remove the screws behind the side cover.
2. Remove the lower dash trim from the vehicle.
3. Remove the gasket on the top of the instrument cluster.
4. Remove the fixing screws (2 pcs) between the top pad and the instrument panel carrier (torque 1.2 Nm).
5. Release the fixing clips (2 pcs) between the steering column cover and the instrument cluster frame.
6. Remove the instrument cluster frame from the vehicle.
7. Remove both the outer face-level vent and the inner face-level vent from the vehicle dash.
8. Remove the instrument cluster from the instrument panel carrier to check the harness connection.
9. Disconnect the x861 from the backside of the instrument cluster.
10. Connect the diagnostic cable TLAN001 to the instrument cluster connector X861.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>