ggm gastro GK1200UG Drinks Fridge Beverage Cooler User Manual

ggm gastro GK1200UG Drinks Fridge Beverage Cooler

This manual has been prepared for the models listed below. You may write RXX at the end of the model name on the rating label of the model. The RXX means which refrigeration gas is used and the energy class of the device.

• GK1200UG
• GK1200US
• GK175UG
• GK175US
• GK374UEG
• GK374UES
• GK374UG
• GK374US
• GKG1325
• LKSU345

INFORMATION

Dear Customer, To use your beverage cooler, which was manufactured and quality controlled in company plants with great care, more efficiently, we kindly request you to read this manual carefully and completely before start using your product, to keep it for further reference and to use your product according to the terms stated herein. If you fail to use your product according to the rules and instructions contained in this manual and/or in case of any usage error, our Company shall not be any way responsible from the breaking down of your product.

Dear Customer, Points to consider within this manual are indicated under the headings WARNING, CAUTION, NOTE and SUGGESTION These headings are defined according to the degree of importance and we kindly request you to read each of them carefully. The information stated under headings WARNING, CAUTION, NOTE and SUGGESTION in this operating manual applies for all stages during the period of use of your product, including transportation and installation.

WARNING!
Contains information for preventing serious damages, which may lead the product out of use, to injury, loss of life and property while the product is in use

CAUTION!
Contains information for preventing the errors, which may decrease the efficiency of your product or failures while the product is in use.

NOTE
Contains explanatory information while the product is in use.

SUGGESTION
Contains information that may be useful while the product is in use.

NOTE
In case of any failure, please contact to our Call Centre, nearest Authorized Service or Customer Care Centre for obtaining information. Our Customer Care Center hotline is available at last page of the operating manual. It is at the discretion of the consumer to take action related to the food inside your cooler in case of any failure. Our company is not responsible from the deterioration of your foodstuff due to any failure or usage error. Our products are manufactured for cooling foodstuff and beverages. Our company is not responsible for any damage that may occur in the products, which areused for another purpose.

THINGS THAT MUST BE DONE BEFORE USING YOUR COOLER

WARNING!

• Do not place your product to a place exposed to direct sunlight or influence area of the heat sources such stove, radiator core, oven, cooker, radiant, and infrared. Otherwise, this may cause a performance decrease, damage of your product or make it become dysfunctional. (Picture 1)
• Your product is set for operating at mains power of 220-240 Volt 50 Hz. Using your cooler with a different voltage may cause it to become dysfunctional and fire. (Picture 2)
• Electrical installation must conform to national regulations. (Picture 3)
• There must absolutely be a residual current relay and a fuse in your electrical installation to prevent the risks of electrical shock and fire.
• Our company is not responsible for the failures and damage that may occur in case of use without grounding.
• Place the product in a damp-free place with unobstructed air circulation.
• You must clean inside your product before the first use
• After placing your product to its place, wait for one (1) hour without moving it before starting use.
• If your cooler is installed under very cold weather conditions, then the waiting period must be at least two (2) hours before start it to operate.
• If you do not use your product for a short time or leave it empty, do not unplug it to save energy. Otherwise, more energy will be consumed for re-cooling your product.
• Unplug your product in case of sudden blackouts. To start again, plug in your product 20 minutes after the electricity is supplied. High voltage occurring at the moment of electricity supply may cause damage of your product and fire.
• Do not allow wild animals and pets to enter into your product or walk around. It may damage your product or cause death and injury of the animals. Furthermore, wild animals and pets may cause fire by causing harm to the electrical installation.
• Never place hot foodstuff into your cooler for cooling purposes.
• The product you’ve purchased is designed and manufactured for cooling and storing bottles and/or canned beverages or packed food only. Please do not use for other purposes.
• Your product is designed for use at indoor places. Do not use your product at outdoor places.
• Do not place materials that must not be cooled down into your product. Do not use your product for defrosting frozen food.
• Product installation, placement, maintenance, and cleaning must be done as stated in the manual. Do not apply anything contrary to the manual. In case of any damage that may happen in your product as a result of such use, warranty conditions will be invalid due to user error. Frost deposit will increase in the products, the doors of which are left open or opened-closed frequently and your product will not be able to perform cooling operation. Therefore, open your product’s door only when you need it. Make sure that the product’s door is closed when you don’t need.

WARNING!

• Since an impact to the glass parts of the products with glass doors by a sharp, pointed object or its contact to a very hot substance may cause the glasses to be broken, this matter must be paid attention particularly.
• Place your product onto a flat surface with no slope to prevent sliding or tilt over of your product.
• Operate your product only at usage position.
• Do not expose your product to direct sunlight.
• Carry and store your product at normal position only to protect it against damages. Actions in contrary may cause loss of the warranty rights.
• Make sure that the discharge valve is closed to prevent frost formation inside your product or high sweating on the glasses.

NOTE
It is at the discretion of the consumer entirely to take action related to the food inside your cooler in case ofany failure. Our company is not responsible from the deterioration of your foodstuff due to any failure or usage error. The product you’ve purchased is designed and manufactured for cooling and storing bottles and/or canned beverages or packed food only. Our company is not responsible for any damage that may occur in the products, which are used for another purpose. Check your product if there are any failures or not immediately after receiving the product you’ve purchased. If there is any damage, contact to your seller within 24 hours. You can update the version of the operating manual from our authorized services. This product contains (WEEE) classification symbol, which indicates electric and electronic hardware. Accordingly, the user must conform to 2012/19/EU European Directive for recycling to minimize the environmental impact of the relevant product. When you intend to throw your product to garbage or to allocate is as scrap, please contact to Authorized Services for learning necessary information. Your device must be delivered to local WEEE disposal institutions in such cases. The pictures shown in this manual are representative only and my vary depending on the model. Since the specifications stated in this manual include all options, some of them may not be present at your product.

SAFETY PRECAUTIONS

The products mentioned in the manual are designed according to national and international security norms and produced under control. The following matters must be considered for safe and secure use.

• Check that your outlet is suitable for the operation of your product. Always use your product with the grounded socket. Make sure that the electrical installation of your building is convenient. Do not use displaced and loose outlets.
• Do not ever use your product with an extension cord or power strip.
• Always follow the instructions in this manual while replacing the bulb The power of the bulb to be replaced is indicated on the device declaration name label, the label just under the lamp and in this manual. Canopy lamps must only be replaced by Authorized Service.
• Lamp replacement for the lightings must only be made by Authorized Service.
• If the power cable is damaged, its replacement must only be made by Authorized Service.
• Please call Authorized Service if your have any doubts about the electrical connection while the product is running.
• Always pull the plug by holding it from the plug-head. Never pull the power cord.
• Do not remove any external protective cover that is not stated in this manual. You may access electrical parts posing a threat to life if the external protective covers are removed.
• Never use pressurized water for cleaning. Pressurized water may cause damage in live parts.
• Do not intervene the device directly in case of any failure arising from the electricity system of the device and/or the electrical installation it is connected. Call the nearest Authorized Service after breaking the electricity current by unplugging the device or turning of the switch.
• Never plug and operate a damaged (such as transportation damage) product. Always call the nearest Authorized Service.
• Always consider maximum loading capacity while loading your product with beverages. Do not exceed the loading line indicated in your product.
• Replacement for the live parts must only be made by Authorized Service.
• Always store packaging materials of your product out of reach of children. Packaging materials (nylon, Styrofoam etc.) may pose a danger for children.
• The product you’ve purchased must not be used by physically (visual, audial) or mentally handicapped people, children, and people with inadequate knowledge without surveillance of a person responsible for their safety. Children must be guarded while using the product and it must be ensured that they are not playing with the product.
• Do not use any material or metal that is not recommended by the manufacturer while defrosting. You may damage cooling parts.
• Do not damage cooling cycle components.
• Do not anyway use the products/materials, which are not recommended by the manufacturer company inside and outside the cabin.
• Make sure that the intervention to be made to your product is certainly made by an authorized service.
• Do not carry, or move the product under any circumstance while it is plugged in.
• Never carry out servicing and repair operations on the product while it is plugged in.
• Substances such as aerosol cans with flammable propellant must not be stored in this product.
• Always abide positioning rules of your product. Not abiding by cooling shutter and grill layouts may cause fire danger.

CAUTION!

Please check the refrigerant gas written on your product label. The following 5 clauses cover the products containing R600a and R290 Hydrocarbon gas.

• Installation of this device must be only made by Authorized Service to reduce flammability dangers.
• Do not obstruct the ventilation holes on the device cover or body.
• Mechanical tools and other apparatus, other than the models recommended by the manufacturer, must not be used for accelerating the defrosting operation
• Cooling circuit must not be damaged.
• Electrical devices must not be used inside the food storage section of the device unless the models are recommended by the manufacturer.
• Installation of this device must be only made by Authorized Service to reduce flammability dangers.

WARNING!

• If your product is damaged or not working properly, please unplug it from the wall outlet. Transfer the foodstuff inside of it to a convenient place and call the nearest Authorized Service.

GENERAL APPEARANCE OF YOUR COOLER

NOTE

Product technical specifications are stated on the labels of the product. Our Company reserves the right to change the technical specifications of the products without any notice.

INSTALLATION OF YOUR COOLER

Selecting the place of installation The operating environment of the product is very important for the smooth operation of your product. While selecting the operating environment,

• Do not place your product exposed to an outdoor environment (on the street, avenue, etc.)
• Be careful not to obstruct the lower shutter of the product with materials such as cardboard, box etc. for proper cooling. (Picture 4)
• Place the product at least one (1) meter away from heat resources (ex: stove, radiator, electric heater, etc.) (Picture 5)
• Do not place it opposite of the air conditioner chutes, under fans, and direct door and window openings. (Picture 6)
• Do not be exposed to direct sunlight. The operation ratio will increase if sunlight comes to the cooler’s glass. That means an increase in the energy consumption.
• Air intake and outlet must be fluent and free for proper operation of the compressor section of your product.
• While approaching your product to the wall, be careful that there is a gap of 150 mm (15 cm) between the wall and the back of your cooler.

WARNING!
In very humid environments, ensure that the floor and wall of the place where the cooler is located is not affected by water; against discharge water overflow danger.In installations performed by Authorized Service, Authorized Service shall inform the consumer on the suitable place for installation and make suggestions, but the consumer shall give the final decision on where the installation will be made. This process shall also be stated on the relevant installation form by Authorized Service. In case of any loss arising from the place of installation of the product according to the final decision given by the consumer, all responsibility related to such loss shall belong to the consumer. Your product gives the best cooling performance according to the climate conditions under the conditions given below. Therefore, be careful that the temperature of the environment where your cooler will be operated is at these levels. Your product gives the best cooling performance according to the climate conditions under the conditions given below. Therefore, be careful that the temperature of the environment where your cooler will operate at these levels. Please check the rating label on the device.

INSTALLATION OF YOUR COOLER.

Positioning
Possible placement positions:

1. In a way that the back side alone is opposite to the wall; be careful that there is a gap of 150 mm (15 cm) between the wall and your cooler. (Picture 7)
2. In a way that is placed to a corner; when you place to a corner, leave a gap of 150 mm (15 cm) behind. You can lean the side corresponding to the corner, to the wall.

The most important point to be considered in all cases of product placement is not to obstruct the ventilation of the compressor assembly. Without exposing your product to any slope, place and operate it in a manner that it is on its feet or wheels. (Picture 8) The freer the compressor assembly ventilation is, the better the device will run.

Hanging

WARNING!

• There is wall hanging apparatus only behind GK1200UG, GK175UG, GK374UEG, GK374UG,LKSU345 models. You do not need to leave an additional gap for these models.

• 2 holes with a diameter of 7 mm and a depth of 40 mm are drilled on a surface, the solidness of which is ensured, on the A axis which you have determined according to the device.

• The expansion bolt of 8 mm is driven into both holes tightly. 2 screws of 4,8×38 YSB DIN NO:7981 are inserted into the expansion bolt that are driven tightly.

• It is necessary to leave a distance of 2-3 mm between the head of the screw and the expansion bolt and for inserting the hanging plates behind the cooler to the screws.
  Note: Leaving the screws excessively long may cause detachment of the cooler.

• Make sure that the slot hole on the hanging plate behind the cooler fits securely.

• While hanging the device onto the expansion bolt, you can align the screw and slot hole from the hole on the side surface of the hanging plate.

Installation
Before positioning, remove and disassemble all packaging materials and bottom wooden pallet of the product. (It may be necessary to lift the cooler for removing the bottom pallet). Insert the replacement parts inside your product according to the installation instructions. Only use genuine spare parts. Please consult to salesperson for minimum period during which spare parts, are available. Inauthentic spare parts may constitute danger for you and damage your product. Place the product anywhere you desire. Consider the placement rules written in the manual while positioning the product. Balance your product in width and in depth by means of a water gauge. Perform balancing operation by using adjustable feet at the bottom front of your cooler. (Picture 9) In models with wheels (optional), wheel brake (optional) must be locked or if there is no wheel brake, it must be guaranteed that the device will not move after the positioning of the product.

Electric Connection Rules
The product will start when you insert the plug into the outlet as shown in picture 10.

WARNING!

• It is forbidden to insert the plug into multiple sockets and to use an extension cord. (Picture 11)
• There is no separate on-off switch on your product.
• Do not contact the cables of your product, which are connected to the mains, to hot surfaces.

The outlet you will use must be grounded. Furthermore, the outlet to be used must have a resistance of at least 10-16 A and be protected with a suitable fuse. Take assistance from our technical service or a competent electrician about the fuse that should be present on the mains where the outlet is connected. Mains voltage and frequency must be the same as the value written on the label inside your product. If your mains voltage is extremely below or above the value indicated, definitely supply the demanded voltage by using a voltage regulator. You can get assistance from an expert electrician in this regard. Do not place your product’s cord onto passageways. This may cause you to get injured and damage your cooler. (Picture 12)

USING YOUR COOLER

Start-up

WARNING!

• This operating manual applies for various device models. Hardware scopes of the models may vary. There may be differences in the pictures.
• Clean inside and all accessories of your product before the first start-up
• If your product has been shaken so much during the transportation and positioning, wait for one (1) our without running your cooler. Thus, the compressor oil, which may enter into the system, will return back. You may damage the compressor if you run it without considering this.
• Insert your product’s plug into an outlet with the alternative current of 220-240V/50 Hz only, which has been installed according to the regulations. (Picture 13)
• You will hear a slight sound from the compressor when your product is running.
• The fan inside your product will stop when you open the door of your refrigerator.
• If the lights of your product are not on, set the 0-1 switch under the canopy to position 1. (Picture 14-15)

For LCD Display Coolers;
Your product has units with transparent LCD placed on the door of your product. You do not need to take any action to activate these units. When you plug in your product, the unit will be activated and the display will start playing. These units placed on your product display images on the transparent display via media cards placed in our factory. These images can only be changed by authorized technical services. The door of your product is specially produced in our factory. Never interfere in any door, display or image malfunctions and call the authorized service immediately.

Setting internal temperature of your product
Temperature settings of your product have been set in our factory in a manner that operates under the most suitable conditions. Protection temperature of the food are observed from the thermometer (optional) equipped in your cooler and set via the thermostat. (Picture 16) However, storing the factory settings is the most appropriate one. The internal temperature of your cooler can be adjusted by rotating the thermostat button (Picture 17). When the thermostat is at position “7”, internal temperature of the refrigerator will be at the lowest level.

Using thermostat
If the product you’ve purchased is equipped with a digital thermostat, please pay attention to the following matters. Digital thermostats are factory-set and do not require any setting. You can change the thermostat setting as specified below. Digital thermostats contain many programs (such as eco mode, night mode). If you believe that there is a problem in your product related to the operation or cooling, please consult to authorized service. When you encounter error codes, stop thermostat alarm and call Authorized Service.

For Eliwell Thermostat;

Set Temperature;

For Carel Thermostat;

For CRA Thermostat;

Defrost function
Your product has an automatic defrost function. Your showcase will melt frost automatically when it is necessary to defrost while running Although your product automatically prevents frost deposit, frost deposit ratio may increase due to high temperature and humidity as well as frequent use of the device. The running period increases as the frost deposit increases. That also increases the energy consumption. In such cases, stop your product and ensure melting of the frost.

DO NOT FORGET!
An evaporator without frost will always run with high efficiency Water from the evaporator drops onto the drop tray at the compressor section. Even though hot gas evaporates water here, it will be better to check and clean once a month

Shutting down your product

• Transfer the foodstuff inside your product to a convenient place.
• Unplug your product. Do not hold your equipment on the cable while unplugging. Unplug by holding the socket. If your product will not be used for a long time, apply the following considerations;
• Clean your product. Otherwise, the humidity on the wall may cause darkening of the internal surface.

CAUTION!
If your product will be stored at an indoor place after shutdown;

• Do not cover it with plastic sheets. Plastic will cause smell and sweating of your product as it does not breathe. Corrosion may be seen as the result of sweating.
• Smell formation may occur in cases where you fail to store your product with the door open.

Loading foodstuff to your cooler
When your product reaches the desired coolness at an empty state, you can load it with the types of foodstuff with the examples given in this manual. (If your product is a thermometer-installed model, you can control the internal temperature of your product from here.)

CAUTION!

• Before loading your cooler with foodstuff, run your cooler empty for two (2) hours.
• Do not place the products that are forbidden to be cooled down into your cooler. Do not defrost frozen products in your cooler.
• Leave a gap of at least two (2) cm between the foodstuff loaded and the upper shelf for air circulation.
• Do not load over the loading line.

CLEANING, MAINTENANCE AND TRANSPORTATION OF YOUR COOLER

CLEANING
Cleaning of your device is composed of two stages, which are internal cleaning and external cleaning. Following warnings must certainly be abided by before starting cleaning.

CAUTION!

• Unplug your cooler before every cleaning.
• Always wear protective gloves during cleaning and maintenance. This will protect you from injuries.
• Never use abrasive and scratching substances (flammable and sparkling, solvents like gasoline, thinner, and acid ) as cleaning agents. Never use flowing and pressurized water for cleaning.

Internal cleaning
Transfer the foodstuff inside your product to a convenient place. Before the internal cleaning, wait until the temperatures of the internal parts of your product reach to the ambient temperature. Always wear protective gloves during cleaning and maintenance. This will protect you from injuries. Remove the accessories from the inside. Perform cleaning with a soft cotton cloth and warm soapy water or by using the cleaning agents recommended by Authorized Service. Dry with a dry cotton cloth. Products, which are not dried, may darken in time. Make sure that no wet or humid area is left in the internal section after cleaning. You can reload your product two (2) hours after running your product as stated in this manual.

External cleaning
Clean with a cotton cloth and warm soapy water. Prevent penetration of cleaning water into the front control panel and lighting section while cleaning. Clean the door gasket by using clean soapy water only.

Maintenance
Clean the dust accumulated on the condenser, which is on the back part of your device with the help of a vacuum cleaner or a dry brush after unplugging the device. Repeat this process a few times in a year.

Transportation of your product
Unplug your product from the grounded outlet. Carry out defrost operation. Carry your product at the normal position. Do not carry horizontally, vertically, tilted or with the door open. Protect your product from the impacts while carrying it. Do not carry your product when it is plugged in or full. In order not to cause any accidents and to prevent the product from getting damaged by falling or sliding, secure your product to the vehicle during transportation.

NOTE
Pay attention to the following considerations if you do not use your product for reasons such as vacation, trip, etc..If you do not use it for a short time: Leave your product in the operating state. If you do not use it for a long time and want to shut it down: Consume the foodstuff inside your product and empty it. Unplug the power cord from the outlet. Apply the defrost and internal cleaning steps in this manual. Dry the inside of the product thoroughly. Darkening may occur in the product that is not dried. Leave the product door open.

Troubleshooting

CAUTION!

• Intervention to any failure that may occur in your product must be carried out by Authorized Service.
• Any intervention that may be done by you may harm you, your employee or your customer, invalidate the product guarantee, and cause material damage (fire, etc).
• In case of any failure, consult to Customer Care or Authorized Service.
• Consult your salesperson to order spare parts and for the minimum period during which spare parts, are available.
• Please contact the seller for the minimum duration of the guarantee.

The power values of the bulbs and LEDs used in your products are stated in the section where they are inserted and may vary in products. Only Authorized Service can intervene bulbs and leds used in your products.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>