RIVERS EDGE LD203 Lockdown 2 Man Ladder Stand Owner’s Manual

: June 9, 2024
: RIVERS EDGE

LD203 Lockdown 2 Man Ladder Stand

Product Information: Lockdown 2-Man Ladder Stand

The Lockdown 2-Man Ladder Stand (Model LD203) is a sturdy and durable hunting accessory designed to provide a comfortable and safe vantage point for two people. The stand has a maximum height of 17’1″ to the shooting rail and can accommodate a maximum weight of 500 lbs. It can be attached to trees with a diameter ranging from 12 to 30 inches. The product meets industry standards and is recognized by participating members.

The package comes with an operator’s manual, which includes an introduction, warranty information, warnings, inspection, and maintenance instructions, hardware identification chart, assembly instructions, setup and use instructions, and an illustrated parts breakdown. The product is covered by a one-year warranty that applies to all components of the tree stand.

Product Usage Instructions

Warnings: Before using the Lockdown 2-Man Ladder Stand, please read and follow the warnings as listed in the operator’s manual. Wear your harness at all times when using this product, and do not exceed the maximum weight limit of 500 lbs. Always inspect the tree stand before each use and make sure all hardware is tight and secure. Do not use this product if any parts are missing or damaged.

Assembly Instructions: Follow the assembly instructions carefully to ensure proper installation of the tree stand. Start by identifying the parts using the hardware identification chart. Then, follow the step-by-step instructions for attaching the ladder sections, attaching the shooting rail, and attaching the seat platform. Be sure to tighten all hardware securely with the provided tools.

Setup and Use Instructions: Once assembled, move the tree stand to your desired location and attach it securely to a tree using the provided straps or chain. Make sure the tree is within the recommended diameter range of 12 to 30 inches. Climb up the ladder carefully, using the provided handrails and steps. Once at the top, sit on the seat platform and secure yourself with the provided harness. Always wear your harness while using this product. Do not stand on the shooting rail or use it as a step. Avoid sudden movements and keep firearms pointed in a safe direction while in use.

Inspection and Maintenance: Inspect the tree stand before each use to ensure all hardware is tight and secure. Check for any signs of wear or damage, including cracks, dents, or rust. Replace any damaged parts before using the tree stand. To clean the tree stand, use a mild detergent and water, and avoid using abrasive cleaners or materials that may damage the finish. Store the tree stand in a dry, cool place when not in use.

The Ultimate Shooting Rail Use Instructions: The Lockdown 2-Man Ladder Stand comes with an Ultimate Shooting Rail that can be adjusted for height and angle. Follow the instructions in the operator’s manual carefully to adjust the shooting rail to your desired position. Always keep firearms pointed in a safe direction while using the shooting rail, and do not use it as a step or support for standing.

For any warranty claims or questions about the product, contact RETI customer service by phone or mail.

PAT. WWW.ARDISAM.COM/PATENTS

Operator’s Manual
LOCKDOWN 2-MAN
Ladder Stand
MODEL LD203
Maximum Height
17′ 1″ to shooting rail
Maximum Field Rating 500 lbs
Tree Diameter Range 12″ to 30″
Wear Your Harness!

PRODUCT MEETS INDUSTRY STANDARDS
RECOGNIZED BY
PARTICIPATING MEMBER

Get parts online at
www.HuntRiversEdge.com

P/N: 35740 C/N: 34887 REV7: 01/05/2022

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand
INTRODUCTION
Rivers Edge® Treestands are engineered with you the hunter in mind. We appreciate your purchase of one of our world class treestands. Follow these few simple instructions and your stand will provide you many years of trouble- free pleasure. Instructions should be kept in a safe place and reviewed at least annually. If for any reason you have a problem with your product or are missing any parts, DO NOT return to the retailer, contact Rivers Edge® Customer Service Department at 800-345-6007 for assistance.
CONTENTS
Introduction/Warranty …………………………………………………………………………………………………………………………………………………………………………………………2 Warnings……………………………………………………………………………………………………………………………………………………………………………………………………………..3-4 Inspection and Maintenance ………………………………………………………………………………………………………………………………………………………………………………4 Hardware Identification Chart …………………………………………………………………………………………………………………………………………………………………………5-7 Assembly Instructions …………………………………………………………………………………………………………………………………………………………………………………… 8-16 Warnings……………………………………………………………………………………………………………………………………………………………………………………………………………… 17 Setup and Use Instructions………………………………………………………………………………………………………………………………………………………………………….18-23 The Ultimate Shooting Rail Use Instructions…………………………………………………………………………………………………………………………………………………. 24 Finished Ladder………………………………………………………………………………………………………………………………………………………………………………………………….. 25 Illustrated Parts Breakdown…………………………………………………………………………………………………………………………………………………………………………26-27
WARRANTY
RETI offers a one-year warranty for all components of the treestand. These warranties apply to the original owner with a proof of purchase. These warranties begin on the date of purchase by the first retail consumer and continue for the period specified above. These warranties apply to products that are not modified, abused or used in a manner that deviates from the product’s intended usage. Minor fading in color is normal and is not covered by warranty. Any corrosion of painted surfaces that occurs as a result of paint being removed or damaged is also not covered by warranty. RETI offers no other warranty expressed or implied. Products for which warranty work has been approved must be sent directly to RETI and performed by RETI. To obtain warranty service and/or replacement instructions, you must obtain prior approval from RETI before shipping your package to us by calling our customer service department at 800-345-6007 or by writing to: Ardisam, Inc., P.O. Box 755, 1730 Industrial Avenue, Cumberland, WI 54829 for a return material authorization number (RMA#). All items must be shipped prepaid. RETI will, at no charge, repair or replace, in RETI’s sole discretion, any product that satisfies the conditions stated above. RETI retains the right to change models, specifications and price without notice.
This equipment has been manufactured under strict quality and safety guidelines. As with any equipment of this type, full understanding of the instructions and its use is mandatory and imperative for the safety of its user. RETI is not responsible for any damages or injuries sustained due to improper use or modification of any of its products, or resulting from any use which deviates from the product’s intended usage. RETI is not responsible for any injuries sustained due to failure to read and adhere to the instructions for use. Any misunderstanding or questions regarding the products of their use should be directed to RETI prior to any use. All RETI treestands are sold with a full body harness (“Fall Arrest System”) that meets standards recognized by the Treestand Manufacturer’s Association (“TMA”). It is the owner’s sole responsibility to inspect the product regularly for damage, improper installation, or conditions that could jeopardize the ultimate safety of the product. Failure to use or improper use of the provided Fall Arrest System may result in serious injury or death. ALWAYS wear the provided Fall Arrest System while using this product. Owner is responsible to understand and follow product field weight rating and must never exceed maximum weight rating. RETI is not responsible for any malfunction or injury resulting from normal wear and tear, damage caused by improper use, improper maintenance, negligence or accidents. This product, if used safely as intended, will provide trouble free service for the useful life of the product. We hope you will enjoy the quality of our products for years to come, and have a safe hunt.

2

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

STOP READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE ASSEMBLY

MODEL LD203
MAXIMUM USE HEIGHT – 17′ 1″ TO SHOOTING RAIL
MAXIMUM OCCUPANCY – TWO (2)
TOTAL WEIGHT LIMIT – 500 LB
TREE DIAMETER RANGE – 12″ TO 30″
WARNING
This product carries strict height and weight restrictions. Do Not use this product if you exceed the total weight limit. Please note that the total weight limit includes the user(s) and their equipment.
WARNING
When hunting from a treestand falls can occur any time after leaving the ground causing injury or death. Always wear a Fall Arrest System (FAS) comprising a full body harness at all times after leaving the ground. You must stay connected at all times after leaving the ground while using climbing and hang-on treestands. Single safety belts and chest harnesses are no longer allowed and shall never be used. If you are not wearing a full body harness properly attached to the tree that is protecting you from a fall, do not leave the ground. Read and understand all of the manufacturer’s Warnings and Instructions and use all safety devices provided by the manufacturer. Contact the manufacturer for any questions. Failure to do so could result in injury or death. Never exceed the total weight limit of the treestand. Never use a treestand during inclement weather such as rain, lightning, windstorms or icy conditions and end your hunt and return to the ground if inclement conditions arise. Never use a treestand while using drugs (even prescription drugs) or alcohol. Never use a treestand while feeling ill, nauseous or dizzy, or if you have a prior medical condition that could cause a problem, that is, heart condition, joints that lock-up, spinal fusions, etc., or if you are not well rested. Never sleep in stand. Never use a treestand on a dead, leaning, diseased or loose barked tree, or a utility pole. Always avoid electrical power lines. Never rely on a tree branch for support.

WARNING
Never jump or bounce on a treestand to seat it to the tree.
Pull up a bow, backpack, or firearm or other equipment only after being secure in the treestand and a firearm must be pulled up with it unloaded, chamber open, and muzzle down.
Always inform someone of the hunting location, where the treestand will be located and the expected duration of the hunt.
A signal device such as a mobile phone, radio, whistle, signal flare or personal locator device (PLD) must be on your person and readily available at all times.
Inspect the treestand and all safety devices each time before use and Do Not store a treestand outdoors when not in use.
Never modify your treestand in any way by making repairs, replacing parts, or altering it except if explicitly authorized in writing by the manufacturer.
Practice installing, adjusting and using your treestand at ground level prior to using it at elevated positions. Study your new stand to become familiar with all of its features and design. Doing so will confirm that the product is manufactured, assembled and installed correctly.
Instructions (written and video) shall be kept in a safe place and reviewed at least annually. It is the responsibility of the treestand owner to furnish the complete instructions to any person who borrows or purchases the treestand.
Use at least three (3) people to install or take down a ladder treestand.
The criss-cross straps/ropes and stabilization devices must be attached before climbing to the platform.
When installing a ladder stand, always bounce on the first rung to set the ladder into the ground according to manufacturer’s instructions before proceeding to climb any higher.
Check every ladder section connection every time you use the stand before you leave the ground. If ladder sections are separating, do not use the stand.
Check the ground under the stand to make sure it is firm and level. Sloping ground or uneven surface (one side on a rock) can cause your ladder to tilt or shift off the tree as you climb.
Always maintain three (3) points of contact when climbing a ladder treestand. Proper three-point contact means having either two feet with one hand or one foot with two hands on the step portion of the ladder or climbing aid at all times.

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

3

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

WARNING
Always lean forward as you climb and attach your harness to the tree before securing the platform to the tree and stepping onto the platform.
Never exceed the stated maximum use height.
Do Not use this product until you have watched the online safety video, understand it, and practiced the techniques for safe hunting discussed in this video. Video can be found with the QR code and/or URL shown on front cover of this manual.
Read and perform all inspection and maintenance tasks before each and every use. Replace any questionable components immediately with RETI original replacement parts.
Do Not crush tubing when tightening bolt assemblies! Identify and familiarize yourself with all parts before you start. Bolt identification chart can be found in the back.
Double check assembly steps to be certain you have correctly assembled this product.
Never use any product that has not been maintained or inspected properly – Your life depends on it!
Replace any and all treestand straps every two years or when any signs of damage or wear exist before.
Always wear the appropriate footwear when using a ladder treestand. A good non-slip safety boot is important to your personal safety. Be especially careful that boot laces do not get hooked on the stand or any of its components (tuck shoelaces into boots before climbing).
WARNING
Only use approved RETI parts. Failure to do so may result in serious injury or death!

INSPECTION AND MAINTENANCE
BEFORE EACH USE PERFORM THE FOLLOWING:
· Inspect all webbing, rope, cord, and strap assemblies for wear or damage.
· Inspect cables and/or cable ends for damage or kinking.
· Inspect all hardware and chain components for damage or wear.
· Inspect for any structural damage to product. (If any exists stop use immediately and call RETI Customer Service.)
· Inspect all nut and bolt assemblies to be certain none are loose.
· Inspect for any missing parts.
· Lubricate all pivot and slide together points with powder graphite, petroleum jelly or silicone spray to prevent noise, wear and rust.
· Inspect entire product for any rust, corrosion, cracks, freezing, excessive heat or rotting damage that may effect the safety of your product. Discard any questionable product.
· Inspect entire product for any structural damage – pay close attention to all weld locations. (Discard product if any damage is found.)
· Using correct wrenches inspect all nut & bolt assembly locations and snug up any that may be loose. Be careful not to crush tubing when tightening!
· Inspect and check operation of all cables, cable ends, cord, rope, webbing, and strap or chain assemblies. Replace with RETI original replacement parts any item or assembly that shows signs of wear, damage, kinking, or functions incorrectly.
· Inspect seat for damage or wear. Replace any seat with factory new that shows signs of structural damage or wear.
· Never modify your stand in any way by making repairs, replacing parts, or altering by adding or attaching anything to it except if explicitly authorized in writing by the manufacturer.

4

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

TOOLS REQUIRED

–

7/16″ WRENCHES

4 MM ALLEN

–

27477

WRENCH

(INCLUDED)

HARDWARE LIST

Item Part No.

Description

29

23572

YELLOW PLASTIC WASHER 2 MM

30

35130

YELLOW CURVED SPACER

31

35225

YELLOW CURVED WASHER

32

36703

YELLOW PLASTIC SPACER 12 MM

34

28839

KNOB M6 X 29 MM

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

2 1

Image

Qty

8

4 4

6

2

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

5

Item Part No.

Description

35

36719

KNOB SILENT LADDER W/STUD

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

Image

Qty

6

39

48679

RUBBER BUMPER STOP

2

40 # 48042B

WING NUT

2

41

26813 BOLT M6 X 20 MM

2

42

48057B SCREW WING

2

43

48240B

BOLT 1/4 X 1-1/2 IN

44

48250B

BOLT 1/4 X 1-3/4 IN

45

48271B

BOLT 1/4 X 2-1/4 IN

6

10 4 2
Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

Item Part No.

Description

46

48270B

BOLT 1/4 X 2-1/2 IN

47 # 48280B

BOLT 1/4 X 3 IN

48

36704

BOLT 1/4 X 3-1/2 IN

49

29676

BOLT 1/4 X 3-3/4 IN

50

36705

BOLT 1/4 X 4 IN

51

35721

BOLT 1/4 X 2-1/2 IN

52 # 48752B

NUT 1/4 IN

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

Image

Qty

14

4

2

3

55

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

7

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

ASSEMBLY INSTRUCTIONS

IMPORTANT ASSEMBLY TIP: Do not tighten any nut and bolt combinations completely until all parts are assembled together! Finger tighten plus one turn of a wrench only! This will temporarily hold the lock- nut on the bolt while helping alignment of all parts! After all parts are assembled together, all nut and bolt combinations must be completely tightened.
mesh hidden for clarity 47
47 47
52 28
9 43

All assembly must be done in this order at ground level before uprighting.
Do not remove labels/warnings from product, they are there for your safety.
Recommended for adult use only.

1
10 52

1. Attach front, middle, and rear platform sections (9, 28 and 10) to J-tubes (1) using ten 1/4-20 x 3 IN bolts (47), four 1/4-20 x 1-1/2 IN bolts (43) and nuts (52).

STEP 1

2. Insert bottom tree blade (22) into ends of J-tubes (1). Slide a strap guide (7) onto each J-tube (1) and align with rear hole on each side. Secure parts together using two 1/4-20 x 1-1/2 IN bolts (43), two 1/4-20 x 1-3/4 IN bolts (44) and nuts (52).

43 44 1 52 22
7

STEP 2

8

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

STEP 3

39

19 18

3. Attach left and right armrests (17 and 18) to rear

platform section (10) using four 1/4-20 x 3 IN bolts

52
17 32

(47) and nuts (52).
Attach seat support (19) to left and right armrests (17 and 18) using four 1/4-20 x 3-1/2 IN bolts (48), 12mm thick yellow spacers (32) and nuts (52). The

spacers must be placed between the seat support

48 and armrests. Be sure to position the seat support with the holes for the rubber seat bumpers (39)

facing up.

Insert the rubber seat bumpers (39) into the holes

10

in the seat support (19).

52

47

4. Attach the top tree blade (3) to the seat support (19) using two 1/4-20 x 2-1/2 IN bolts (46) and nuts (52).

19

52 3

46

STEP 4

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

9

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

STEP 5

2 18
46
52 5. Attach the backrest tubes (2) to the left and right armrests (17 and 18) using four 1/4-20 x 2-1/2 IN bolts (46) and nuts (52).
17

6. Slide the backrest (23) onto the backrest tubes (2). Attach the backrest spreader (11) to the top of the backrest tubes (2) using two 1/4-20 x 1-1/2 IN bolts (43) and nuts (52).

11 52 43 2 23

STEP 6

10

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand
25
7. Attach the seat assembly (25) to the rest of the treestand using two 1/4-20 x 3-3/4 IN bolts (49), four yellow washers (29), two 12 MM thick yellow spacers (32) and nuts (52).

STEP 7

52 29 32

8. Attach the rear fabric of the seat assembly (25)
to the seat support (19) using the rear seat support (20), three 1/4-20 x 2-1/2 IN carriage bolts (51) and nuts (52). Pay close attention to DETAIL A for proper assembly. The seat fabric will be sandwiched between the seat support (19) and rear seat support (20). Once the bolts are tightened, the plastic rod within the fabric sleeve will secure the fabric in place.
NOTE: Pay close attention not to pinch the plastic rod between the seat support (19) and rear seat support (20) while tightening the bolts.

25 20 19
52

DETAIL A

Plastic Rod

Seat Fabric 51
20

29 49
51

STEP 8

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

11

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

STEP 9

9. Assemble the shooting rail (12 and 24) by inserting the small diameter tube of adjustable shooting rail parts (24) into the shooting rail (12). Align the holes and secure together using two 1/4-20 x 1-1/2 IN bolts (43) and nuts (52).
12
43 24
52

STEP 10

10. Attach the shooting rail assembly to the rest of the treestand using two 1/4-20 x 4 IN bolts (50), two yellow washers (29), four curved yellow spacers (30) and nuts (52).
Attach the shooting rail adjustment knobs (34) to the adjustment plates on the left and right armrests (17 and 18) using two M6 x 20 MM bolts (41).

18 34
41

17

50 29

30 30

52

12

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

mesh hidden for clarity
21 9

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

11. Attach the footrest (21) to the front platform section (9) using two 1/4-20 x 2-1/2 IN bolts (46), two yellow washers (29), four curved yellow washers (31) and nuts (52).

52 29

31

46

31

STEP 11

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

13

mesh hidden for clarity

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

12. Slide the top ladder section (14) into the pockets on the J-tubes (1) and secure using two 1/4-20 x 1-3/4 IN bolts (44) and nuts (52).

Pre-assemble the platform braces (5) with the ladder hand rails (4) by inserting one end of each platform brace (5) into the lower end of each ladder hand rail (4) and aligning the holes.

Then, attach the pre-assembled platform braces (5)

52 52 44

7 46

and ladder hand rails (4) and four strap guides (7) to the rest of the treestand using six 1/4-20 x 2-1/2 IN bolts (46) and nuts (52). Pay close attention to DETAIL A and DETAIL B for proper positioning of

1

strap guides (7).

52 46

4

46

7

5

14

STEP 12

DETAIL B

DETAIL A

14

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

52 27
16 45

13. Attach the ladder ratchets (27) to the ladder section with the stabilizer bar mount (16) using two 1/4-20 x 2-1/4 IN bolts (45) and nuts (52). Set aside for now.

STEP 13

14. Ladder sections are assembled on the ground in the following order: bottom ladder section (15), ladder section with stabilizer bar mount (16), middle ladders section (13) and the top ladder section (14) with the treestand top assembly.
The ladder sections are secured together with the six Silent LadderLocks with stud (35).

STEP 14

14 35

13

16

15

Ground

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

15

DETAIL A

7 7 56 7

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand
15. Before uprighting the stand to the tree, you must attach the two long straps (56) to the assembled treestand. Begin by feeding one end of each strap through the three strap guides (7) under the platform and at the top of the ladder on both sides. SEE FIGURE 1 and DETAIL A.
Attach the looped ends of the straps together near the center of the ladder with the carabiner on the end of the tether rope (57). SEE FIGURE 1 and DETAIL B.
Run the opposite end of each strap down to the ladder ratchet (27) on either side of the ladder. Run the strap down through the center slot in the ratchet and “ratchet” just enough to loosely hold the strap in place. They do not need to be tight. This is only temporary to keep them out of the way while you upright the stand to the tree. SEE FIGURE 1 and DETAIL C.
Lastly, run the tether rope (57) down the length of the ladder, wrap around the Silent LadderLocks (35) that are near the ladder ratchets (27) and loosely tie in place. SEE FIGURE 1 and DETAIL C. You are now ready to upright the ladder. Follow setup and use instructions on following pages.
Note: Model LD200 depicted varies from manual model but the strap system is the same.

57 27

FIGURE 1

DETAIL B DETAIL C

35

Carabiner

16

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

STOP READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE SETUP AND USE

WARNING
Double check assembly steps to be certain you have correctly assembled this product.
Study your new stand to become familiar with all of its features and design. At ground level, following provided use instructions, practice attaching stand to tree and removing stand from tree. Practice sitting, standing, and using this product before attaching overhead. Save these instructions for future reference. You must always use the provided Fall Arrest System (FAS) while using this product.
Always use at least three (3) people to install or take down a ladder treestand. Always have two people stabilize the ladder before climbing to the platform the first time after every set-up.
Be absolutely sure the tree blade(s) on stand and the stabilizer bar are contacting tree before climbing ladder.
Stabilizer bar must always be correctly and securely attached to ladder and tree before climbing ladder.
Make sure ladder bottom is firmly seated on dry, level ground. Attach your harness tether to the tree before securing the platform to the tree and stepping onto platform. Refer to the Full Body Harness instructions.
Never ascend or descend ladder without straps/ropes securely holding ladder to tree and stabilizer bar securely attached. Failure to correctly perform these steps can cause the ladder to collapse/buckle-over backwards during the initial ascent to attach ratchet strap resulting in serious injury or death.
Always lean forward as you climb and attach your harness to the tree before securing the platform to the tree with the provided ratchet straps.

WARNING
Always maintain three (3) points of contact when climbing a ladder treestand. Proper three-point contact means having either two feet with one hand or one foot with two hands on the step portion of the ladder or climbing aid at all times.
Always wear the appropriate footwear when using a ladder treestand. A good non-slip safety boot is important to your personal safety. Be especially careful that boot laces do not get hooked on the stand or any of its components (tuck shoelaces into boots before climbing).
Never stand on seat, it is designed for sitting only.
Do Not allow excessive strap buildup in ratchet as this will prevent the ratchet teeth from engaging causing slippage.
Always attach ratchet straps securely while using this product!
If seat is removable, be certain it is securely attached when in use.
Some models include a shooting rail. Never lean against, lean over, or sit on shooting rail. It is designed as a shooting rest only. Always be aware that the shooting rail can swing to one side or pivot up and down.
Some models include a footrest, which is designed as a footrest only. Never stand on footrest! Always be fully aware of foot placement.
Some models include a multi-piece stabilizer bar system. Be sure attachment hardware goes through all extension tubes of the stabilizer bar.

WARNING
Bring ratchet strap(s) up with you in a pocket – Do Not carry in your hands!

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

17

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

SET UP AND USE INSTRUCTIONS

WATCH THE SET-UP AND USE VIDEO ONLINE AT
WWW.HUNTRIVERSEDGE.COM
TO ASSIST WITH THE SET-UP OF YOUR TREESTAND

WARNING
Never use a treestand on a dead, leaning, diseased or loose barked tree, or a utility pole. Always avoid electrical power lines. Bring ratchet strap(s) up with you in a pocket – Do not carry in your hands!
1. Select a straight, healthy tree. Do Not attempt to install on a tree that is not healthy.
2. Place the assembled product lying on the ground in front of the tree with the bottom ladder section approximately five feet away from the base of the tree.
3. Position one person at bottom end of ladder. This person has to prevent the ladder end from tilting up and from skidding across the ground when platform end is lifted.
4. Position two people at the platform end of the ladder, lift the platform end and continue uprighting by walking toward bottom end of ladder while moving hands along ladder rails. Stand ladder up against chosen tree on dry, level ground. Use caution when ladder comes over center against the tree, as shown by arrow “A”. SEE FIGURE 2.
5. Once elevated completely, carefully slide the base so that the sitting and standing platforms are parallel to the ground, as shown by arrow “B”. SEE FIGURE 2.
6. Step back and look at the ladder top to see that both the lower platform tree blade and upper tree blade are contacting the tree. Adjust as needed so both of the tree blades are contacting the tree.
7. Step down hard on bottom step to push ladder legs into the ground, as shown by arrow “C”. SEE FIGURE 2.
8. While two people hold the stand in place, the third person should complete the necessary steps on following pages to secure the stand to the tree.

During installation and removal of ladder treestands, you must always and properly use the included Full Body Harness (Fall Arrest System). Refer to the Full Body Harness instructions included with this product for proper use.
FIGURE 2

A

C

B

18

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

9. Begin by removing the long straps (56) from the ground level ratchets (27) and let them hang down on either side of the tree. SEE FIGURE 3.
10. Hook the large carabiner (58) to one of the long straps (56) that are hanging down near the tree. SEE FIGURE 3. If the tree has branches between the ground and the top of the stand, proceed to the next step. If the tree is free of branches between the ground and the top of the stand, skip ahead to STEP 12.

FIGURE 3

56 56
58

Note: Model LD200 depicted varies from manual model but
the strap system is the same.

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

19

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

11. If the tree has branches between the ground and the top of the stand, before hooking the two long straps (56) together behind the tree with the carabiner (58), you must first get both straps on the same side of all of the branches. To do so, simply use the telescoping stabilizer bar (6) to lift up and drop the strap that has the carabiner hooked to it over the branches.
a. Hook the carabiner onto the end of the stabilizer bar as shown in FIGURE 4.
b. Then lift up and drop over each branch. The weight of the carabiner will drop the strap back down to ground level after each branch you drop it over.
c. Repeat dropping it over the branches until both straps are on the same side of all of the branches. SEE FIGURE 5. Then there will be a clear path for the straps and carabiner to rise up the back of the tree, all the way to the top of the stand.
FIGURE 4

FIGURE 5

6

58

6

56

57

20

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

12. Hook the two long straps (56) together behind the tree with the large carabiner (58). SEE FIGURE 5. Be sure to lock the carabiner with the screw locking mechanism. SEE FIGURES 6 A-C.

FIGURE 7

13. Unwrap the tether rope (57) from the Silent LadderLocks (35).

Pull the rope down to raise the two long straps and carabiner up

the back of the tree. SEE FIGURE 7. As the carabiner nears the

top, you may have to use a back and forth “sawing” motion with

the two straps so that the carabiner rises all the way up directly

behind the bottom tree blade (22). The straps should be parallel

22

with the platform of the stand. SEE FIGURE 8. If needed, you can

use the telescoping stabilizer bar (6) to help raise the carabiner

up.

WARNING

DO NOT use this product without the carabiner in the locked position. Failure to follow these instructions may result in serious injury or death!

FIGURE 6-A

FIGURE 6-B

FIGURE 6-C

56 57

1. Turn knob to unlock 2. Press open latch

2. Turn knob to lock

FIGURE 8

58

STRAPS AND CARABINER MUST BE STRAIGHT BEHIND TREE BLADE AND
PARALLEL WITH THE PLATFORM

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

21

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

14. Once the straps (56) and carabiner (58) are all the way up the back of the tree, unhook the tether rope (57) from the two long straps (56) and set aside. The tether rope can later be used as a haul line to pull your gear up into the stand. Feed the straps down through the ladder ratchets (27) and ratchet a few cranks just to hold the straps in place. SEE FIGURES 9 A-D for proper use of ladder ratchets. Do not fully ratchet the straps tight yet.
15. Fully collapse the telescoping stabilizer bar (6) and install to the ladder using one wing bolt (42) and wing nut (40). SEE FIGURE 10. When the stabilizer bar is fully collapsed and the lever handles are aligned on the top, the three holes in the first three sections should line up.
16. Release the first clamp and extend only the bark-biter section of the stabilizer bar until it contacts the tree. Adjust the length of the stabilizer bar as needed and make sure it is parallel with the ground. Align the nearest hole and insert a wing bolt (42) and wing nut (40) and hand tighten to secure the length of the stabilizer bar. SEE FIGURE 10. Then attach the 8′ ratchet strap (55) by forming a cinch knot around the stabilizer bar with both ends. SEE FIGURE 11. Wrap around the tree and ratchet tight.
17. Now that the stabilizer bar is installed, you can finish tightening the ground level ratchets (27) to secure the stand to the tree.
18. This ground level ladder-to-tree attachment will prevent the ladder from pulling away from the tree while ascending to the top for the final ratchet strap attachment. The same holds true when ladder removal is necessary. You are now ready to climb up and complete the final installation steps.
FIGURE 11

FIGURE 9-A FIGURE 9-C

FIGURE 10 / STEP 15

42

40

FIGURE 9-B FIGURE 9-D

55 6

6 40
42

22

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

INSTALLING THE RATCHET STRAPS (54)
19. Be certain ladder bottom is firmly seated on dry, level ground. With two people securely holding the base of the ladder, use the three point contact climbing method to slowly climb the ladder and carefully keep a constant hand grip on the ladder at all times. Always lean forward, towards the tree, while climbing. Attach your harness tether to the tree before securing the platform to the tree with the provided ratchet straps. Refer to the Full Body Harness instructions included with this product.
NOTE: Bring large ratchet straps up with you in a pocket. DO NOT carry in your hands!
20. Once platform is reached and safety harness is secured to the tree, hook S-hook with long strap through one of the holes provided in top tree blade. Feed the long strap through the center slot of ratcheting mechanism and back around through tightening lever. SEE FIGURES 12 A-B & 13.
21. Wrap the ratchet assembly around the tree and hook other S-hook through opposite hole on top tree blade. Pull tail of long strap until most of the slack is taken out. Be sure entire strap is even and at the same level all around tree. “Ratchet” tight to tree. This will securely attach only the seat portion to the tree and prevent movement. SEE FIGURES 12-C & 13.
NOTE: To release ratchet, simply pull the release lever and open tightening lever wide open (flat). SEE FIGURE 12-D.
22. Repeat previous two steps for the bottom tree blade attachment. Place S-hook through holes provided on bottom tree blade.
23. To take the ladder stand down, first check the security of the ground level ratchets (27) and stabilizer straps (56). Then, with two people holding the bottom of the ladder, climb up, secure your safety harness to the tree and remove the top two ratchet straps (54). Then climb down and reverse the set-up and use instructions to complete the removal of the stand.

FIGURE 12-A FIGURE 12-C

FIGURE 13

FIGURE 12-B
FIGURE 12-D
Ratchet Straps Carabiner Long Strap

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

23

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

THE ULTIMATE SHOOTING RAIL USE INSTRUCTIONS

The shooting rail on this stand is unique. It has both up-and-down and in-and- out adjustment. It can also be flipped down and tucked away into the platform to get it out of the way for bow hunting.
SHOOTING RAIL ADJUSTMENT
1. To adjust the shooting rail up or down, simply loosen the two knobs, slide them up or down in the slots to the desired height, and tighten them back up. SEE FIGURE 14.
2. To adjust the shooting rail in or out, simply release the two clamp levers and slide the shooting rail to the desired position. Then, lock in place by flipping the levers back down. SEE FIGURE 14.
SHOOTING RAIL TUCKED-AWAY
3. To flip the shooting rail down and tuck it away into the platform, first flip it up over your head and let it rest against the tree.
4. Then, loosen the two knobs and slide/rotate them down in the slots and out of the way. SEE FIGURE 15 AND DETAIL A.
5. Then, flip the shooting rail down in front of you and release the two clamp levers. Flip it all the way down and slide it into the slot in the platform. Then lock in place by flipping the levers back down. SEE FIGURE 15.

FIGURE 14 FIGURE 15

Note: Model LD200 depicted varies from manual model but the shooting rail design is the same.

DETAIL A

24

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

FINISHED LADDER

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

ASSEMBLED PLATFORM SECTION

TOP LADDER SECTION
MIDDLE LADDER SECTION
LADDER SECTION WITH STABILIZER
MOUNTS RATCHETS
BOTTOM LADDER SECTION

SILENT LADDERLOCK

RATCHET STRAPS
LONG STRAP CONNECTED WITH CARABINER
STABILIZER BAR CAM STRAP
TELESCOPING STABILIZER BAR

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

25

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

ILLUSTRATED PARTS BREAKDOWN

23 38

46 7
14
35

43 26
12 52

40 13
42
6

51

34

29

25

20

50

18

41

52

32 39

29

11 52

52 36

32

3 52

2

43 38 52

47 46

32 50 46

36
43 52

37 43
29 52

47
21 31

19
10 52 28

30 29

48 49

30

24

52

46 9 31
47

17 47

22

52

44

1 7 43

8
16 27
45 52
15

52 44

7
46 5
4 52

46 mesh hidden for clarity

26

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

Operator’s Manual
LOCKDOWNTM 2-MAN Ladder Stand

PARTS LIST

ITEM # PART # DESCRIPTION

QTY.

1

34936 J TUBE

2

34975 BACKREST TUBE

2

3

35084 TOP TREE BLADE

1

4

35085 LADDER HAND RAIL

2

5

35086 PLATFORM BRACE

2

6

35100 STABILIZER BAR

1

TELESCOPING

7

35129 STRAP GUIDE

6

8

35131 INSERT STABILIZER BAR

1

MOUNT

9

35170 PLATFORM FRONT

1

10

35173 PLATFORM REAR

1

11

35184 BACKREST SPREADER

1

12

35187 SHOOTING RAIL ROUND W/

1

VINYL DIP

13

35465 MIDDLE LADDER SECTION

1

14

35467 TOP LADDER SECTION

1

15

35469 BOTTOM LADDER SECTION

1

16

35471 LADDER SECTION W/

1

STABILIZER

17

35199 LEFT ARMREST

1

18

35200 RIGHT ARMREST

1

19

35202 SEAT SUPPORT

1

20

35215 REAR SEAT SUPPORT

1

21

35219 FOOT REST W/VINYL DIP

1

22

35222 BOTTOM TREE BLADE

1

23

35228 BACKREST

1

24

35229 ADJUST SHOOTING RAIL

2

25

35231 ASSEMBLY SEAT

1

26

35374 INSERT SHOOTING RAIL

2

27

35715 LADDER RATCHET

2

28

35843 CENTER PLATFORM

1

29

23572 YELLOW PLASTIC WASHER 2

8

MM

30

35130 YELLOW CURVED SPACER

4

31

35225 YELLOW CURVED WASHER

4

32

36703 YELLOW PLASTIC SPACER 12

6

MM

ITEM # 34 35
36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
53 54
55
56 57 58

PART # DESCRIPTION

QTY.

28839 M6 X 29 MM KNOB

2

36719 KNOB SILENT LADDER W/

6

STUD

29712 SQ PLUG 22 MM

4

30407 ROUND PLUG 18 MM

2

32783 SQ PLUG 25 MM

4

48679 RUBBER BUMPER STOP

2

48042B WING NUT

2

48057B BOLT M6 X 20 MM

2

26813 SCREW WING

2

48240B BOLT 1/4 X 1-1/2 IN

10

48250B BOLT 1/4 X 1-3/4 IN

4

48271B BOLT 1/4 X 2-1/4 IN

2

48270B BOLT 1/4 X 2-1/2 IN

14

48280B BOLT 1/4 X 3 IN

14

36704 BOLT 1/4 X 3-1/2 IN

4

29676 BOLT 1/4 X 3-3/4 IN

2

36705 BOLT 1/4 X 4 IN

2

35721 CARRIAGE BOLT 1/4 X 2-1/2 IN 3

48752B NUT 1/4 IN

55

ITEMS BELOW NOT SHOWN

40697 HARNESS

2

35135 ASSEMBLY 8 FT RATCHET

2

STRAP W/ S-HOOKS

35159 RATCHET STRAP ASSEMBLY

1

8 FT

35160 STABILIZER STRAP 17 FT

2

30777 TETHER ROPE

1

35743 LARGE CARABINER

1

NO EXTENSIONS AVAILABLE FOR THIS MODEL. NEVER MODIFY OR EXCEED ORIGINAL STATED USE HEIGHT!

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007

27

by
Ardisam, Inc. 1730 Industrial Avenue, Cumberland, WI 54829

Phone: 800-345-6007 Fax: 715-822-2124 www.huntriversedge.com

*All weights, specifications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Warning labels in some product images may have been removed for photography purposes only. Props shown in photos not included. Some assembly may be required.