MiBOXER FUT035P 2 in 1 LED Controller 2.4G Instruction Manual
- June 17, 2024
- MiBOXER
Table of Contents
2 in 1 LED Controller ( 2.4G )
Instruction Manual
Product features
Product adopt the widely used 2 4GHz wireless technology with the features of
low power consumption, long signal transmitting and strong anti-interference,
etc.
Product has auto-transmitting function. Widely used on the controlling of
hotel lighting and home lighting
|
Color temperature adjustable
---|---
Dim brightness
2.4G RF wireless transmission technology
Remote control distance 30m
Auto transmitting
Support Smartphone app control (2.4GHz gateway is needed)
Support third party voice control (2.4GHz gateway is needed)
Set up output mode
Set up correct output mode based on the feature of lights Setting method:
Press “SET” button continuously to switch output mode (attention: it willlog
out without operation within 3 seconds)
Output mode sheet ( confirm output mode based on color of indicator)
| Indicator color | Red Light | Green Light |
|---|---|---|
| Output | Single Color Mode | Dual White Mode |
PUSH Dimming
Short press PUSH switch:
Turn ON/OFF light
- Stepless dimming brightness.
- Long press and release your finger, then repeat long pressingto increase or decrease brightness.
Compatible with these 2.4G
RF remote controls (Purchased separately)
2.4G RF Remote control instruction
-
Linking Code Instructions****
Power off 10 seconds and power on again or short press “SET” one time or turn on light via PUSH switch| Short press ” I ” button 3 times within 3 seconds.| Lights blink 3 times slowly means linking
is done successfully.
Linking failed if light is not blinking slowly, Please follow above steps again. (Note: Light that have linked can’t link again)
-
Unlinking Code Instruc�ons
Power off 10 seconds and power on again or short press “SET” one time or turnon light via PUSH switch| Short press ” I ” button 5 times within 3 seconds.| Lights blink 10 tomes quickly means unlinking is done successfully.
Unlinking failed if light is not blinking quickly, Please follow above steps again. (Note: Light haven’t linked that don’t need to unlink)
-
Auto transmitting (2.4G RF remote signal)
The light can transmit remote signal to another light automatically while the distance between lights are 30m, the remote control distance is unlimited (attention: alllights must be linked with same remote)
-
PWM high frequency / low frequency switching (only for remote control) Switch to high frequency (16KHz):
Press “OFF” button 1 time within three seconds and press “ON” button 5 times, Activated successfully once led light flashes 2 times quickly Switch to low frequency (250Hz):
Press “ON” button 1 time within three seconds and press “OFF” button 5 times, Activated successfully once led light flashes 2 times slowly. -
“Do Not Disturb” mode is activated and shut down (default activated) Turn on “Do Not Disturb” mode (wide using in the area which have power failure frequently to save energy)
2.46 RF Remote turn on and turn off instruction
Turn on “Do Not Disturb” mode:
Press “OFF” button three times within three seconds and press “ON” button
three times, Activated successfully once led light flashes four times quickly.
Attention: Do not disturb mode is activated
-
When the light is OFF status (For example: Use app or remote to turn offlight) The light is OFF status once you turn off power and turn on again
(User must turn off and turn on power twice times to activate light oruse APP / remote to activate light) -
When the light is ON status
The light s ON status once you tur off and turn on power one time.
Turn off “Do Not Disturb” mode:
Press “ON” button three times within three seconds and press “OFF” button
three times, closed successfully once led light flashes four times slowly
Attention: The light will be always “ON” status if you turn on and turn
off power once user closed “Do Not Disturb” mode.
Attention
- Please tum off power supply before installaion.
- Plesse ensure input voltage to be same as requirements from device.
- Don’t disassemble device f you are not expert, otherwise it wil damage it
- Please do not use the light n the place with widely range metal area or strong electromagnetic wave nearby, otherwise, the remote distance will be seriously affected.
Scan QR code to watch 2 4GH2 series video instruction O enter into following lnk directly bttps://miboker com/light/video/Ipc remotehtml
https://miboxer.com/light/video/1pc_remote.html Made in China