WOODBRIDGE B0735 Modern One Piece Toilet User Guide

WOODBRIDGE B0735 Modern One Piece Toilet

READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION.

CAUTION!
TWO-PERSON LIFTS REQUIRE 2 PEOPLE TO LIFT AND DURING THE ENTIRE INSTALLATION OF THIS PRODUCT INSTALLATION OF THIS PRODUCT BY AN INEXPERIENCED INSTALLER MAY RESULT PERSONAL INJURY OR DEATH! We reserve the right to change, update, modify, alter, or redesign this manual/product or its policies without prior notice! We shall not be liable for any injuries or property damages in connection with this product during installation or use! This product must be installed by a fully insured and licensed plumber only. Installation of our products by anyone other than a fully insured and licensed plumber shall void the limited warranty. We recommend that such licensed plumbers have experience in the installation of products.

Limited warranty is void on any commercial installation
We are not responsible for local code compliance for this product. Building and plumbing codes may vary from state to state by location. We are not responsible for providing any compliance certifications. Under no circumstances will we be liable for any incidental damages sustained in connection with this product Neither manufacturer, distributor, nor retailer is responsible for water damage or flood caused due to the use of this product. Under no circumstances will we be liable for any fees, installation/reinstallation/removal cost, subsequent damage or transportation in case of a product defect.

TOILET COMPONENTS
During unpacking the product and before installation inspect your new product for any damages or missing parts. Do not attempt to install or operate the product if the product is damaged.

TOOLS REQUIRED FOR INSTALLATION

DIMENSIONS/TECHNICAL DATA

IMPORTANT

• Measurements are + 3/8″ and subject to change without notice
• Specifications & Configurations are subject to change without notice
• Please measure the toilet on-site before installation

INFORMATION

• Please note that installers) must be certified or the warranty will be voided.
• Measurements herein supersede all others published before the publication date shown below

WATER SUPPLY LOCATION & TECHNICAL INFORMATION

You may connect the water supply line using two different options. In both options distance from the floor to the center of the supply line must be 5 1/2″. In Supply Position 1, the water supply is located behind the toilet and is offset by 4 1/2″ from the installed toilet’s centre. In supply Position 2 the water supply line must be offset by 10″ from the center of the installed toilet.

IMPORTANT

• Measurements are + 3/8″ and subject to change without notice
• Specifications & Configurations are subject to change without notice
• Please measure the toilet on-site before installation

INFORMATION

• Please note that installers) must be certified or the warranty will be voided.
• Measurements herein supersede all others published before the publication date shown below

IMPORTANT!
Shut off the main water supply before installation!

REMOVE OLD TOILET

1. Shut off the water supply line. If you do not have a shut-off valve near the toilet shut off the main water supply line.
2. Flush the old toilet and make sure that the tank is empty.
3. Disconnect and remove the water supply line connected to the toilet’s tank.
4. Remove the old toilet, bolts, and nuts from the closet flange.
5. Clean the closet flange area from the old wax ring and putty sealant using a putty knife from the base area.
6. Clean any remaining debris and wipe any water at the installation area
7. Temporarily plug the flange on a floor with a flange plug or towel to prevent gasses from escaping

IMPORTANT! The mounting surface area
NOTE! Inspect the existing closet flange for must be clean, dry, and levelled before damage. If damaged, replace it with a new flange installation of the new toilet! before proceeding to the installation

PREPARE CLOSET FLANGE
Make sure that the rough-in is 12″ by measuring the distance from the wall to the centre of the closet flange. See Figure 1

• Using a template outline the area where the toilet will sit with a pencil or tape to locate the flange bolts and make a solid connection between the wax ring and flange when set.
• Make sure to remove the template, leaving the outline before installing. See Figure 4

Locate and remove the template from the carton. Place over toilet flange. Measure from the back wall to make sure it is square/even with the wall. Check your shut-off valve to make sure it clears the back of the template. See Figure 3

INSTALL WAX RING
Important: safety glasses must be worn by the installer and all bystanders. Cover the floor with a soft-close blanket. Carefully turn the toilet on its side or upside-down on the blanket with the assistance of a second person. Install a wax ring over the horn discharge located on the bottom of the toilet bowl. See Figure 5

Note: Ceramic is a fragile material. You must always cover the floor with a soft-cloth blanket if you want to put the toilet on the floor on any side other than the bottom of the toilet. If you do not cover the floor with a soft-close blanket contact of the toilet with the floor may and will cause minor or moderate scratches on the toilet’s surface. Always Use Soft-Cloth Blanket

INSTALL NEW TOILET

Step 1. Lift and carefully put the toilet over the closet flange inside the outline made by the template so the closet bolts can go through the mountingholes in the toilet’s base. Once the bowl is in position press the bowl down with a slight twisting motion in a level position towards the floor. Apply your body weight to evenly compress the wax ring to create a watertight seal. Make sure that the bowl is as levelled as possible to have a nice seal tight. Do not rock the toilet back and forth and side to side as it may and will break a seal and you will need to replace the wax ring again and start the installation process over. See Figure 6

Step 2. Once the toilet is set and levelled install washers and nuts over the closet bolts. Tighten nuts. Do not overtighten the nuts. It may and will cause damage to the toilet’s ceramic base. Please keep in mind that because this is a skirted trap-way toilet, it may require a little more time, patience and accessibility to complete the installation. See Figure 7

CONNECT TOILET’S TANK

TO THE WATER SUPPLY LINE
Connect the water supply line between the tank and the water shut-off valve using a toilet hose (not supplied). When connecting the toilet hose tighten the coupling nut to the tank by 1/4 turn beyond the hand tight. Do not overtighten the nut on the tank connection. It may and will cause water leakage.

Turn on the valve on the water supply line and allow the tank to fill. Check all connections for leakages and tighten them as needed. Once the tank is filled with water flush it 4-5 times to perform a test of the flushing system. At the same time check the bottom of the toilet for leaks to make sure that the wax ring is properly installed and sealed.

If there are no leaks you are ready to finalize the installation. If any shims are installed at the bottom of the toilet bowl you may trim them. Apply silicone around the base of the toilets. Allow 24 hours for silicone to dry before start using the toilet. See Figure 8 Important: Leaks may not occur during or right after the installation. Make sure to check for leaks every couple hours first day installed and and occasionally check it every day for the next week to ensure that the toilet is properly installed and no leaks occur. If any leaks occur immediately shut off the water supply line valve and contact your local plumber to fix all leaks.

Important
Under no circumstances will we be liable for any incidental damages sustained in connection with this product Neither manufacturer, distributor, nor retailer is responsible for water damage or flood caused due to the use of this product. Under no circumstances will we be liable for any fees, costs of installation/reinstallation/removal, subsequent damage or transportation in case of the product defect

TOILET SEAT ADJUSTMENT

• Assemble items 3,4,5 & 6 to make the 2 fittings.
• Insert the fittings into the holes but don’t tighten fully.
• With the seat in the vertical position, push it onto the fittings and adjust the seat position to suit the toilet bowl.
• Remove the seat by placing it in the vertical position and lifting it off. This may require quite a bit of force so we recommend wedging palms face-up at the base of the seat to pry off.
• Then tighten the fittings and cover with the brushed nickel plates. (Item number 2)
• Re-attach the seat, in the vertical position by pushing it onto the fittings until you feel it click.

ADJUSTMENT & MAINTENANCE (DUAL FLUSH VALVE)

BASE INSTALLATION

Important Note: Flush GPF amount is factory set. No additional adjustment is required. This page is for reference only. All adjustments are already made by the manufacturer.

• Check the dual flush valve and make sure that it does not have any damaged or missing parts
• Install the base with the rubber gasket in the tank, and turn the screw as illustrated to make sure there is no water leakage and no looseness
• Install a body of the flush into the base and make sure they can be rotated clockwise arbitrarily.
• Rotate the valve clockwise to adjust its position inside of the toilet’s tank
• Install the sealing gasket

FLUSH VOLUME ADJUSTMENT
Full flush and half Flush range will decline when the button is mated died from the bottom.

REFILL TUBE ASSEMBLY
Put the refill tube into the white cap hole firmly The refill tube can’t be lower then the water sealing level.

TROUBLESHOOTING

• If the rod is too short, please re-adjust it (outward rotation).
• If the rod is too long, please Cut off the extra length and re-adjust it.

ADJUSTMENT & MAINTENACE (FILL VALVE)
Important Note: Flush GPF amount is factory set. No additional adjustment is required. This page is for reference only. All adjustments are already made by the manufacturer.

Instructions
When the valve is installed, the critical level mark on fill valve (identified by C.L. mark on valve body) should be at least 1″ above the top of the overflow pipe.

Required
Water temperature: 36-112°F

Important
Under no circumstances seller shall not be liable for any and  all incidental damages sustained in connection with this product Neither manufacturer, distributor, nor retailer is responsible for water damage or flood caused by to use of this product. Under no circumstances seller shall not be liable for any fees, or costs of installation/reinstallation/removal. subsequent damage or transportation in case of a product defect.

IMPORTANT
Do not use or drop any chlorine or any other chemicals. Use of chemical products will result in damage to the fill valve and flush valve components and may cause flood and property damage. Do not overtighten bolts/nuts as it may and will cause damage to the toilet parts and componets.

PREPARATION
Remove the worn-out fittings and clean your tank before the installation of the new ones. There might be a lot of impurities in your tank that may cause damage to the new parts if you do not clean them out. The tank must be absolutely clean before installation.

WATER LEVEL ADJUSTMENT

Check the fill valve

1. Press the buckle and unscrew. make sure that it does
2. Pull the valve upwards or press down to the desired height. not have any damage or 3. Unscrew the valve body and fasten the buckle missing parts
3. Rotating screw, raise or lower the water level  to adjust the water level to a suitable position (water volume will gradually increase when the adjuster is moved upward from the bottom.)

FILL VALVE INSTALLATION

• Install the valve into the tank. Do not use any wrench tools. Fasten with hand only.
• Connect the water supply to the fill Turn off the water supply valve valve. Turn on the water. before height adjustment of the toilet’s fill valve.
• Put the refill tube into the white cap hole firmly.

CLEANING & TROUBLESHOOTING (FILL VALVE)

FILL VALVE CLEANING

• Shut off the water supply line before filter cleaning.
• Carefully, take out the filter from the inlet by using pliers.
• Use water to wash and clean the filter and adapter from any debris.
• Re-install the filter and re-connect the water supply line.

TROUBLESHOOTING

MAINTENANCE & CARE
Use soft sponges or soft cloths to clean the surface. Always rinse thoroughly any cleaning solutions immediately after cleaning. Do not any chemical remain on the surface for extended periods.

IMPORTANT!
DO NOT USE: Abrasive cleaners such as acid, ammonia, bleach, and similar solutions. The use of such solutions may cause corrosion, finish peeling, and/or dulling the surface.
DO NOT USE: Abrasive sponges or cloth. Never use steel, wool, or wire brushes that will permanently scratch the surface.

FILL/FLUSH VALVES MAINTENANCE & CARE
Do not pour any amounts of chlorine or any other chemicals into the tank. Use of chemical products will result in damage to the fill valve and flush valve components and may cause flood and property damage and will void the warranty.
Note: fill and flush valves are maintenance-free. No maintenance is required.

LIMITED WARRANTY COVERAGE WOODBRIDGE

5 YEARS TOILET BOWL & TANK
WOODBRIDGE® warrants its toilet bowl & Tank against fading staining of the glaze as a result of a defect in materials and workmanship for five(5) years from the purchase date. SCRATCHES ARE NOT COVERED UNDER WARRANTY.

1-YEAR TOILET SEAT
1 YEAR FILL VALVE & FLUSH
VALVE  1 YEAR PLUMBING PARTS  WOODBRIDGE® warrants factory-installed plumbing parts and fittings, and electrical components to be free from defects in materials and workmanship for one (1) years from the TOILET RESPONSIBILITIES OF OTHERS Inspecting the unit before installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defects or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility.

In the event of a problem, the unit must not be installed. WOODBRIDGE® is not responsible for failures or damage that could have been discovered, repaired, or avoided by proper inspection and testing before installation. Damage occurring in transit is the responsibility of the carrier. The user or installer MUST open the crate and inspect the unit for damage when it is delivered. If damage is discovered, it must be reported immediately to the seller and the carrier in writing, and an inspection requested. Failure of the carrier to respond should be reported to the seller and the carrier. Your freight claims should be
filed promptly thereafter.

The manufacturer warrants this product to be free of manufacture defects during the above-mentioned warranty time. Please keep a copy of the original invoice as proof of purchase. WOODBRIDGE will, as its option. (1) repair or replace the defective part(s) or product(s) at no charge: (2) issue a refund of the original purchase price of the products) (Valid within 30 days from the date of purchase): or (3) issue a credit to be applied toward the purchase of a new WOODBRIDGE product. Shipping/delivery charges may apply and are in WOODBRIDGE’s sole discretion. Woodbridge products must be installed by a fully insured and licensed plumber only. Installation of any of our products by anyone other than a fully insured and licensed plumber shall void the limited warranty.

This limited warranty shall not apply to goods which have been subject to accident, negligence, improper installation, product abuse, product misuse, or use of cleaners containing abrasives, alcohol or other organic solvents, whether performed by a contractor, service company, or yourself, are excluded from this

LIMITATIONS AND EXCLUSIONS

This warranty does not cover any claim arising from abuse, misuse, negligence, accident, improper installation or operations on the part of the purchaser. This warranty is void if the WOODBRIDGE” is subject to alteration, or if repairs are attempted by anyone other then an authorized agent of WOODBRIDGE. This warranty does not extend to plumbing or components installed by dealers, installers or by any party other than WOODBRIDGE® WOODBRIDGE® will not be liable for loss of use of the WOODBRIDGE® inconvenience, or any other incidental or consequential costs, expense or damages. Please note that some states do not allow the exclusion or limitation of incidental damages.

DISCLAIMER
Except as expressly provided, there shall be no warranty or obligation, express or implied, oral or statutory. No dealer or other person has the authority to make any warranties or representations concerning, WOODBRIDGE or its products. In no event shall WOODBRIDGE® be held responsible for any such warranties or WOODBRIDGE® responsibility under this limited warranty is limited to only to replacement parts and no other costs. WoodBrIoGe” will not be responsible for labour charges and/or damage incurredby installation, repair or replacement, nor for any indirect incidental or consequential damages, losses , injury or costs of any nature relating to this product.

Except as provided by law, this limited warranty is instead of and excludes all other warranties, conditions, and guarantees, whether expressed or implied. statutory or otherwise, including without restriction that merchantability of fitness for use. This limited warranty is non-transferable. This limited warranty only applies to products purchased and installed in the United States. This limited warranty covers the original consumer purchase onlv and does not include business. commercial or. industrial use of this product.

WARRANTY SERVICE
NOTE : When requesting a warranty, be sure to have the following:

• Copy of original invoice
• Date of installation
• Description and pictures of the defect
• Model number or description of the model

To obtain warranty service and replacement parts, pis contact Woodbridge Customer Service. Woodbridge will determine whether to repair or replace your product, issue a refund or issue a credit.

WOODBRIDGE
15600 Blackburn Ave, Norwalk, CA 90650 USA
Customer Service Phone: 562-229-0088
(Monday – Friday 9 AM – 5 PM Pacific Time)
Or Email: help@woodbridgebath.com
www.woodbridgebath.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>