FALCON RIDGE CF-UFORCE-FC04 Cf Moto Uforce Full Cab Instruction Manual
- June 4, 2024
- FALCON RIDGE
Table of Contents
CF-UFORCE-FC04 Cf Moto Uforce Full Cab
Instruction Manual
CF-UFORCE-FC04 Cf Moto Uforce Full Cab
Instructions for Installation and Care of CF Moto U Force Full Cab with Aero-
Vent Poly Windshield CF-UFORCE-FC04.
Notice: Do not smoke inside the cab or expose the enclosure to direct
flames. Cab is Flammable.
Be sure to read these instructions thoroughly before opening and installing
the enclosure. The installation is best done when the temperature is 70
degrees F. or warmer. The temperature affects the adhesive Velcro, if
conditions prevent installing in warmer weather it helps to store the adhesive
Velcro at room temperature prior to installation.
Carefully open the carton and remove the enclosure on a large flat surface
that is clean and free of dirt. Check over the parts included in the carton
with the parts list shown below:
Soft Doors
Adhesive Velcro Hook Strips: 18 each————3″
Adhesive Velcro Hook Strips: 2 each————36”
Snap Screw Studs: 15 each (1 extra)
Rear Window
Adhesive Velcro Hook Strips:
“ “ “ “: 2 each————5”
“ “ “ “: 1 each————32”
Top Cap
Webbing Straps w/ 2” loop: 4 each
Webbing Straps w/ Grommets: 2 each
If any parts are damaged or missing please contact customer service
at606-845-7439.
The cab for your U-Force is made up of 5 different components that work
together to enclose your vehicle. Install the cab in the following order.
Soft Doors
-
Begin by holding the door up to the frame and attaching it using the double-sided Velcro strips sewn perpendicular to the edge of the door. At each of the double-sided strips take one of the 3″ adhesive Velcro strips and adhere it to the inside of the frame. Then wrap the double-sided strip around it so that the adhesive strip holds it firmly in place. the following diagrams show how it should look.
-
Next, take the 50″ adhesive Velcro strip and run it down the back of the roll cage facing towards the rear of the vehicle. You will see two double-sided Velcro tabs sewn along the back of the doors. The adhesive strip must be aligned so that both tabs can attach to it. See the photo below.
-
Once all the Velcro is in place the last thing to do is install the screw snap studs. NOTE: The best way to install the snap studs is to put them in the sockets in the door first. Then push them into the plastic to make an indention. Then pull the screw stud out and screw it into the plastic where the mark was made. See Photos Below.
REAR WINDOW
-
Begin by placing the two 5″ and one of the 45″ adhesive Velcro strips across the top of the roll cage. Make sure to place them on top of the bar. Photo below shows how it should look.
-
Next, place it on the two Velcro tabs down the sidebars. Start at the top at the crossbar and work your way down the tube.
-
The bottom of the Rear Window is held in place by 4 straps with a ladder lock buckle. The two center straps will go around the frame bar just under them, the two end straps will go down and around the piece that holds the seat belt latch. The photo below shows how this should go.
POLYCARBONATE WINDSHIELD:
Install using the directions included with the windshield.
TOP CAP
-
If you have a Lexan windshield already installed on your Z Force you can do one of two things. You may use the straps with a loop sewn to one end and wrap the roll cage under the rear-view mirror. If you choose you may also use the straps with grommet holes in one end. To use these just use one of the bolts on the windshield. Put the grommet through the bolt and reattach. The strap with the loop should look like the photo below.
-
Next, take the other two straps with a loop sewn on one end and wrap them around the roll cage in the rear just under the safety bar..
-
Now place the top over the entire vehicle, the front of the top is identified by the sides not being as steeply curved and begin by lacing the front straps through the ladder lock buckles sewn to the front corners of the top. The diagram below shows how to use ladder buckle.
-
Now run those straps up and through the ladder lock buckles sewn to the rear of the top. You will now need to tighten and loosen the strap of the top so that it is centered correctly.
Cleaning and Storage Recommendations:
- Before removing the Cab for storage, make sure it is very clean in order to prevent scratching of the window panels. Clean with a soft rag or sponge using a mild liquid detergent soap and warm water solution. Never rub the windows with a dry cloth or rag! Let the Cab dry thoroughly before attempting to roll it for storage.
- It is important that the Cab be rolled up for storage rather than folding. Folding will cause damage to the windows!!! Carefully roll up the Cab similar to the way it was when it was packed at the factory. On a large, clean, and flat surface, fold the doors over the rear panel first, then, interleave the top and windshield on top of the doors. Begin rolling the Cab into a roll approximately 8 inches in diameter. Put the rolled Cab back into the carton for storage at normal room temperature. It is best not to expose the Cab to either extremely hot or cold temperatures when storing.
- A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of the Cab Enclosure. In addition, if the additional hook and loop sets are needed, they can also be ordered. Thank you for your purchase!
Return Policy
If for any reason you choose to return this product it must be returned within
30 days from date the item is received. You MUST package the product exactly
as it was originally packaged from the factory to get a full refund for the
product!
The vinyl windows should never be folded when packaging in the box or for
storage purposes. Lay all the windows on top of each other with the canvas
folded in between and the paper (if available) on both sides of the windows.
All returned products will be inspected upon arrival at the production
facility and must be in unused, factory-new condition to receive a refund – a
25% restocking fee will apply.
If ordered from Falcon Ridge please call at
606-845-7439 to gain a return
authorization number, use our preferred shipping carrier (UPS) to return the
item (unless the item is defective, you are responsible for paying the
shipping to return the item.) Any returns submitted to Falcon Ridge without a
return authorization number will be charged a 20% restocking fee. If ordered
from one of Falcon Ridge’s many distributors, you must first call them and see
what their return policy is. Once your item reaches our production facility,
our customer satisfaction team will inspect your item to ensure unused,
factory-new condition.
NOTE: All windshields must be returned with the original protective film
intact and not removed. Do NOT REMOVE if you have any intentions of returning
the item. Refund/ replacement of a windshield will only be processed on items
with original protective film or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect
them during transit and ensure your returned item arrives back factory fresh,
and in new resalable condition (any returned items that have been used,
altered or damaged in any way will not be subject for a refund.) All contents
including instruction manuals, accessories, hardware, Velcro, etc. must be
included in your return shipment. Only items in OEM factory new condition will
be approved. Once returned items are received, credit will be issued to the
original credit card/ payment method used for the purchase. Outbound shipping
and return shipping cost will not be refunded. Please allow 4 to 6 weeks for
your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of our Falcon Ridge Cab Enclosures, Tops &/or
Windshields! Below are the terms under which your product is covered under our
manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure,
tops and/or windshield due to defects of the product. Please refer to the
return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this
time frame we will gladly correct the problem or replace the enclosure, tops
&/or windshield. Upon submitting for the correction or replacement, we will
need to receive pictures of the defect in material or workmanship along with
the receipt from the date of purchase.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>