GOLDEN LIGHTING 6937-O3P Valentina 3 Light Outdoor Pendant Instruction Manual
- June 17, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 6937-O3P Valentina 3 Light Outdoor Pendant
Product Specifications
- Model: 6937-O3P NB-MBW
- Fixture Type: Pendant Light
- Maximum Wattage: Refer to fixture specifications
- Material: Metal and Glass
- Color: Nickel Bronze with Matte White Glass
- Height: Varies (adjustable during installation)
- Installation: Ceiling Mount
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island:
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24 inches of island. Fixtures should hang at least 30 inches above the countertop.
Pendants & Chandeliers Above a Dining Room Table:
Fixtures should stay at least 30 inches above the table. Use a fixture that is 12 inches narrower than the width of the table.
Pendants and Chandeliers in Open Areas:
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
Installation Instructions:
- Raise canopy up to the ceiling and secure with decorative nuts to the mounting screws.
- Install light bulbs (not included) into sockets in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage.
- Carefully slide glass shades over sockets.
- After installing the fixture, apply a silicone rubber caulking to seal the gap between the canopy and the mounting surface.
- Turn on the power and test the fixture.
Frequently Asked Questions
How do I identify the fixture’s wires?
The fixture wires are typically labeled as A, B, C, etc. while house wires are labeled as Hot, Neutral, and Ground. Ensure you match the corresponding wires correctly during installation.
What is the recommended height for pendant lights above a kitchen island?
For optimal lighting and aesthetics, pendant lights should hang at least 30 inches above the countertop of the kitchen island.
Can I install this pendant light on a sloped ceiling?
It is recommended to check the product specifications and guidelines for sloped ceiling compatibility. Some fixtures may require additional mounting accessories for sloped ceilings.
- Pendants & Linear Pendants Above a Kitchen Island
- Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop
- Pendants & Chandeliers Above a Dining Room Table
- Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.
- Pendants and Chandeliers in Open Areas
- The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors
- The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment. Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit
Love your light and want to show it off? Follow us, share a picture, and tag us on Social…
Assembly Instructions
How to Identify the Fixture’s WiresComment identifier
- Hot: Smooth, Black, or Transparent with Black Inner Thread
- Neutral : Ribbed, White or Transparent with White Inner Thread
- Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement parts
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap. 1. Mounting strap (B) contains several pairs of threaded holes. Find the pair of holes that best match the hole spacing in the junction box and your fixture’s canopy (G). Two sets of mounting screws (A & D) should be attached to the mounting strap (B). You may need to use hex nuts (C) to hold mounting screws (A) in place. 2. Pull the house wires through the center of the mounting strap (B). Secure mounting strap (B) to the junction box with mounting screws (D) and a screwdriver. Tighten the screws securely.
ASSEMBLING THE FIXTURE
3. Measure to determine the desired length of the cable that connects the shade (J) to the canopy (G). Unscrew the post small screw at the bottom of the canopy (G) with the provided tool (H). Feed the cable into the post at the bottom of the canopy (G) until the desired length of the cable is reached. Trim the excess wires coming from the other end of the canopy (G) while leaving 8” of cable to connect the wires later. 4. Adjust buckle (F) that sits inside the canopy (G) at least 8” down from the top end of the cut cord. Pull the cord down toward the shade (J) slightly until the buckle (F) touches the hex nut found on the interior of the canopy. Fasten the cable in place using the tool provided (H) to tighten the post small screw found at the bottom of the canopy (G).
CONNECTING THE WIRES
5. Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
6. Raise canopy (G) up to the ceiling and secure with decorative nuts (I) to the mounting screws (A). 7. Install light bulbs (not included) into sockets in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Carefully slide glass shades (K) over sockets (M). After installing the fixture, apply a silicone rubber caulking to seal the gap between the canopy (G) and the mounting surface. Your installation is now complete. Turn on the power and test the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>