somfy Sonesse 30 24V DC Zigbee User Guide
- June 17, 2024
- somfy
Table of Contents
PROGRAMMING GUIDE
ZIGBEE STANDALONE SOLUTION
USING YSIA REMOTES
ZIGBEE STANDALONE SOLUTION USING YSIA REMOTES
VERSION 1.0 | JUNE 2023 | Prepared by PROJECT SERVICES
OVERVIEW
DESCRIPTION
The Somfy Zigbee Standalone Solution using the Ysia remotes defines the new
process to follow for initial set up and adjustments without using the TaHoma
switch and TaHoma pro app. This offers direct two-way communication between
remotes and motors for programming and control utilizing the Zigbee technology
protocol.
This solution provides the ability for pairing and settings needed for all
users from the manufacturers, installers, and the end user. Programming
options include pairing remotes, adjusting rotation direction, and setting end
limits.
NOTE: Advanced motor settings require the use of the TaHoma pro
application.
TaHoma Pro account access is required ahead of time to use the TaHoma Pro app.
TaHoma pro is the recommended tool to set a motor and to pair a remote.
TaHoma pro allows basic settings of rotation direction and end limits, as well
as the advanced settings of a motor including speed adjustment, tilt & lift
products, and soft start and soft stop duration.
RESOURCES & APPLICATIONS
Reference the Somfy Help Me Pro app for step-by-step product guidance on smart
devices: www.somfypro.com/services-support/useful-tools/help-me-
app
Additional individual product information is available on
Somfypro.com
Subscribe to the Somfy YouTube Channel
www.youtube.com/somfysystems
Visit Somfy U for all the training you need – your pace, your place
www.somfyu.com
SYSTEM REQUIREMENTS
NOTE: Pri or to programmi ng, all remotes and motors must be powered and
have the programmi ng buttons and LED i ndi cators accessi ble.
Refer to the Buttons & Indicators section of this guide to reference thei r
locati ons.
Follow applicable local and international standards regarding electrical
installations.
To ensure electrical safety, Class III motors should be powered by a Safety
Extra Low Voltage(SELV) voltage source. Use power supplies or chargers
recommended by Somfy to power or recharge the motors.
Ensure motor batteries are fully charged prior to installation.
-
Programming Somfy Zigbee motors and remotes is limited to room-based distances
NOTE: Distance limitation will be influenced by environmental conditions. -
Recommended limit of 6 remotes programmed per motor
-
Pairing remotes to motors will create individual remote to motor networks
BUTTONS & INDICATORS
Ysia 1 & 5 ZIGBEE REMOTES
Ensure the remote is powered.
Ysia 1 & 5 Zigbee remotes require 2 AAA LR03 1.5V Alkaline batteries to be
installed (included with the product).
Pressing any button will illuminate the LED(s).
LED INDICATORS | LED OPERATION | LED TYPE | INDICATION |
---|---|---|---|
STATUS LED: | VERIFICATION | Remote is sending a command | |
VERIFICATION | Confirmation of setting applied to the motor | ||
SETTING | Remote in Setting Mode with a paired motor | ||
SETTING | Remote is in scanning mode in a Somfy |
Zigbee solution – polling to pair motors
| WARNING| Error with setting or sending a command
CHANNEL LED:| | VERIFICATION| Indicate the selected channel
NOTE: Channel 5 is indicated by 4 solid channel LEDs.
BUTTONS & INDICATORS
ZIGBEE MOTORS
WAKING THE MOTOR:
Ensure the motor has required power available.
Using a small paper clip or similar, BRIEFLY PRESS the Programming Button on
the head of the motor
OR
PLUG IN the battery supply/charger.
The motor will jog (briefly move up and down), and the LED will illuminate
GREEN for 2 seconds.
The LED will blink AMBER continuously during programming for 3 minutes and
then time out.
ROLLER MOTOR
TILT MOTOR
CORD LIFT MOTOR
DRAPERY MOTOR
MOTOR STATUS LED INDICATORS:
AMBER
MOTOR IS NOT SET IN SETTING MODE IN ADJUSTMENT MODE
GREEN
MOTOR IS CHARGING CONFIRMED SETTING
RED
LOW BATTERY CHARGE THERMAL PROTECTION IMPOSSIBLE SETTING
NOT ILLUMINATED ONCE PAIRED AND OPERATIONAL
INSTALLATION
MOUNTING & POWER
Mounting Bracket Installation
NOTE: The Ysia remote is designed to be wall mounted in portrait
(vertical) orientation when not in use.
Refer to product installation instructions for additional details.
-
REMOVE the screw cover from the bracket
-
INSTALL the included mounting bracket
• Use the included screws to mount the mounting bracket onto the mounting locations
NOTE: Consider using alternate hardware depending on the mounting surfaces. -
REPLACE the screw cover onto the bracket
Battery Installation & Replacement
NOTE: The Ysia remote requires 2 AAA LR03 1.5V batteries for operation
(included with the product).
Once the batteries are installed, new remotes will automatically go into
Programming Mode.
- PRESS down on the top-middle of the battery cover below the Channel Selector button
- SLIDE the battery cover down to remove
- FOLLOW product markings for battery orientation
- INSERT batteries into the correct positions
- SLIDE the battery cover back into position
IDENTIFY THE MOTOR MODE
This section will help identify the state of a motor at any time.
Thi s secti on does not apply to drapery motors.
- ENSURE the motor is powered or charged
- LOCATE a paper clip or other small device to access the Programming Button on the motor
- A BRIEF PRESS of the motor Programming button may be required to wake up internal battery motors that are not paired to a remote
Follow below to determine the mode of the motor if in delivery mode or during initial power up.
Factory Mode
Motor has no limits set & no remote paired
OPERATION FROM PROGRAMMING BUTTON
Motor doesn’t move sequentially from a brief press of the Programming Button
located on the motor head (Motor limits are NOT set)
NOTE: The motor will go back to Delivery Mode if left untouched for 15
minutes.
Installer Mode
Motor has limits set & no remote paired
OPERATION FROM PROGRAMMING BUTTON
Motor operates sequentially from a brief press of the Programming Button
located on the motor head
User Mode
Motor has limits set & remote(s) paired
OPERATION FROM PROGRAMMING BUTTON OR REMOTE
The motor LED is off, and the motor operates sequentially from a brief press
of the Programming Button located on the motor head
The motor will be operational from the remote
SET UP
FACTORY MODE – PAIRING & SETTING
NOTE: It’s important to determine if the Ysia remote will be shipped with
the motorized product to determine which method wi ll be used to complete
programmi ng.
Motor Initial Setting
Programming & Scanning Modes:
-
ENSURE motor is powered
NOTE: If the motor LED is blinking AMBER (which means the motor is in Programming Mode), skip to step 4 -
PRESS & HOLD the motor Programming button for 3 seconds until the first jog (brief up & down movement of the motor)
-
WAIT for the blinking AMBER LED on the motor head
-
SELECT the correct channel to program if using the Ysia 5 Channel remote
-
While nearby the motor (within 5 feet), BRIEFLY PRESS the UP and DOWN Buttons simultaneously on the remote
NOTE: The Status LED on the remote will quickly blink GREEN and then blink AMBER to initiate Scanning Mode.Radio reception of the motor is reduced in Programming Mode, keep remote(s) within 5 feet of the motor head while programming.
Scanning takes several seconds and links to the nearest motor in Programming Mode.
-
WAIT for scanning to complete to establish a link with the motor
-
Once the motor LED stops blinking AMBER and the remote LED blinks GREEN two times, the motor LED will blink GREEN and jog once to confirm the link
NOTE: The remote continues blinking AMBER while in Programming Mode. -
If the wrong motor is linked, BRIEFLY PRESS the UP and DOWN buttons simultaneously on the remote to start a new scanning session and find the next motor in Programming Mode
-
Once the correct motor is linked, CONFIRM motor rotation is correct by using the UP or DOWN buttons
NOTE: To reverse the rotation, PRESS & HOLD the MY button until the motor jogs once.
For drapery, the UP button should open, and the DOWN button should close the drapery.
Motor Limit Setting
All motors require limit setting to be completed during initial setup.
Use the steps below to set motor limits for all types of motor.
NOTE: Motor limit setting doesn’t require an order of which direction is set first.
For Drapery Motors: Limits are set automatically by moving the motor in each direction
NOTE: The motor will continuously run until it reaches the mechanical end limits.
Setting the upper limit: -
Using the remote, PRESS & HOLD the UP Button to move the motor to the desired upper limit
-
Once the desired limit is reached, BRIEFLY PRESS the MY and DOWN buttons at the same time, the motor jogs to confirm setting
NOTE: The motor moves incrementally when the buttons are momentarily pressed while fine tuning the limits.
Setting the lower limit: -
Using the remote, PRESS & HOLD the DOWN Button to move the motor to the desired lower limit
-
Once the desired limit is reached, BRIEFLY PRESS the MY and UP buttons at the same time, the motor jogs toconfirm setting
-
FOLLOW the steps below to set the mode and exit programming with or without pairing the remote
Limits are set and remote is not yet paired.
SET MOTOR TO INSTALLER OR USER MODE
This section describes how to set motors into Installer or User Mode
concluding Factory Mode with Ysia remotes.
Follow the process below to exit programming with or without pairing the
remote.
SET MOTOR TO INSTALLER MODE
Without pairing the remote to the motor
Refer to the Installer Mode section for next steps.
PRESS & HOLD the remote UP and DOWN buttons until the remote LED is solid
GREEN.
(For approximately 5 seconds)
The motor LED continues to blink AMBER for 3 minutes.
NOTE: Internal battery motors only:
Automatically enter Delivery Mode 15 minutes later.
SET MOTOR TO USER MODE
Pairing the remote to the motor
Refer to the User Mode section for next steps.
BRIEFLY PRESS the remote
Programming Button, the LED goes solid GREEN then goes off to confirm settings
& pairing. The motor jogs to confirm settings.
INSTALLER MODE
This section includes remote pairing with motors and advanced grouping
functionality of the Somfy Zigbee Standalone Solution.
Network Management – Motors & Remotes
- A network is created and managed by the remote
- Network sharing is a key operation to manage group controls – pairing more than one remote to a motor or adding new remotes in an installation to control existing motors
Pairing A Remote Or Channel To A Motor
The following steps allow for adding a single remote to a motor which has
limits set and is not paired.
WARNING: If the installation requires more than one remote per motor,
follow Groupi ng Remotes secti on pri or to addi ng motors to multi ple
remotes.
If a TaHoma is present on the installation, use the TaHoma or the TaHoma pro
application
- PRESS & HOLD the motor Programming Button for 3 seconds until the motor jogs
- WAIT for the blinking AMBER LED on the motor
- LOCATE the remote to use and SELECT the Channel to use if using a 5-channel remote
- BRIEFLY PRESS the Programming Button of the remote to add
- CONFIRM the remote LED begins blinking AMBER, then briefly blinks GREEN then goes off, CONFIRM motor LED blinks GREEN then goes off followed by one jog
NOTE: This may take several seconds; once the remote LED blinks GREEN and
goes off the remote pairing is complete. If unsuccessful, try again closer to
the motor.
The remote or channel is now paired to the motor.
Grouping Remotes
Network sharing allows for managing groups and for adding new remotes into an
installation with multiple independent networks. Use the steps below to add
remotes into a group network where new and existing remotes are paired with
respective motor combinations.
NOTE: When remotes are added to an existing network, previous remote
pairings are lost and need to be re-paired after the network sharing process.
- LOCATE the paired remote and all additional remotes to combine on the same network
- PRESS & HOLD the Programming Button on the remote to add (R3) until the remote Status LED blinks RED three times, then RELEASE
- CONFIRM the remote Status LED is blinking AMBER
- REPEAT steps 2 and 3 for all additional remotes (Example: R2 & R3)
- POSITION all remotes in proximity (within 5 feet of each other) to share the network between each other
- Using the existing paired remote (R1), BRIEFLY PRESS the Programming button to share the network with additional remote (R2), the LED on both remotes will turn GREEN
- WAIT until the LED blinks GREEN to share the network with R3
- REPEAT steps 5-7 for all additional remote(s)
- Remote pairing is lost during the network sharing process, RECREATE any previous pairings lost during the process – Refer to Pairing A Remote Or Channel To A Motor section of this guide
NOTE: Once the remotes are reset, the motors paired to those remotes will
enter into Programming Mode for 10 minutes to recreate the pairings and avoid
the need of accessing the motor Programming Button.
The remotes are now on a shared network and the Status LED will illuminate
GREEN when a button is pressed. If the remote Status LED blinks RED when a
button is pressed, it is not on a shared network.
Pairing Additional Motor(s) To A Remote Or Channel
Remotes and channels allow for pairing multiple motors to the same group.
Use the steps below to add motors to the group remote that is paired using the
network of the first motor.
- LOCATE the additional motor to add to the existing remote network
- PRESS & HOLD the motor Programming Button for 3 seconds until the motor jogs once
- WAIT for the blinking AMBER LED on the motor
- POSITION the previously paired remote near each additional motor to add (Keep remote within 5 feet of the motor head)
- BRIEFLY PRESS the remote Programming Button to pair it to the additional motor
- CONFIRM the remote LED blinks GREEN, followed by the motor LED blinking GREEN the LED will go off and the motor jogs
- REPEAT the steps above for each additional motor
- CONFIRM operation of all motors from the remote
Grouping Channels Of Remotes
Use the steps below to combine multiple channels that are paired to individual
motors into a single channel of a 5-channel remote.
The steps below can also be used to copy and paste channels from one remote to
another.
-
LOCATE the remote and IDENTIFY the individual channels to combine onto a single channel
NOTE: The role of each channel remains customizable according to the user needs. -
PRESS the Channel Selection button to select the channel where the motors to be added to the group channel are present
-
PRESS & HOLD the remote Programming Button for 3 seconds, the motor will jog
-
PRESS the Channel Selection button to select the group channel
-
BRIEFLY PRESS the remote Programming Button
-
WAIT for the motor to jog once
-
REPEAT the operation with all desired channels
Delete A Remote Or Channel
The following steps allow for deleting a remote or channel from a motor.
WARNING: If a TaHoma is present on the installation, use the TaHoma or
the TaHoma pro application
NOTE: To exit Programming Mode at any time, PRESS & HOLD the UP and DOWN Buttons for 5 seconds.
-
LOCATE the remote and SELECT the channel(if using a 5-channel remote) to be deleted
-
PRESS & HOLD the remote Programming Button for 3 seconds, then RELEASE
-
CONFIRM the motor jogs once and the LED is blinking AMBER
-
BRIEFLY PRESS the UP and DOWN Buttons to activate Scanning Mode of the remote in proximity of the motor to be removed
NOTE: If multiple motors are paired and the wrong motor is linked, BRIEFLY PRESS the UP and DOWN buttons simultaneously on the remote to start a new scanning session and find the next motor in Programming Mode Remote LED will blink AMBER then GREEN, shortly after the motor LED goes out and jogs once. -
PRESS & HOLD the remote Programming button for 5 seconds until the remote LED goes solid GREEN, then RED, the motor LED blinks GREEN, then goes off and the motor jogs once
-
TEST the remote or channel to confirm it has been deleted
NOTE: Remote Status LED wi ll bli nk RED when channel or remote is
deleted.
The remote or channel is now deleted.
USER MODE
Available Commands
This section details motor operation via the Ysia remotes in User Mode.
NOTE: Refer to the Installer Mode section for adding or removing motors
or remotes.
Channel Selection:
Use the Channel Selection button on the remote to select between channels to
control motors or groups.
Control a motor or group:
UP Button: Used to raise, open, or tilt Short Press: Sends motor to the upper
limit/open position
Long Press: Moves tilting motors up, release to stop
NOTE: PRESS & HOLD for desired length of travel.
MY/STOP Button: Used to stop motor movement or move to previously saved
my position Single Press: Stops the motor during movement
Quick Double Press: Moves motor to “my” position
DOWN Button: Used to lower, close, or tilt Short Press: Sends motor to the
lower limit/closed position
Long Press: Moves tilting motors down, release to stop
NOTE: PRESS & HOLD for desired length of travel.
“my” Position
Follow the process below to set the desired “my” position for motors.
-
CONFIRM the motor is powered
-
LOCATE the correct remote for the motor or group
-
SELECT the correct channel (If using an Ysia 5 remote)
-
PRESS & RELEASE the UP or DOWN Buttons to move the motor, then PRESS the MY Button at the desired favorite position to stop the motor
-
PRESS & HOLD the MY button until the motor jogs
NOTE: PRESS & HOLD for at least 2 seconds. -
CONFIRM the GREEN LED on the remote is blinking
-
RELEASE the MY button after the LED goes to solid GREEN and the motor jogs once
-
MOVE the motor to the upper or lower limit, then DOUBLE PRESS the MY Button to confirm the “my” position is set
The “my” favorite position is now set at the current position.
APPENDIX
[APPENDIX A] ADJUST END LIMITS
The process below is used to adjust the product limits of travel.
NOTE: End limit adjustments should be done by the installer for proper limit setting and prevent damage to the products.
Enter Limit Adjustment Mode
-
CONFIRM the motor is powered
-
LOCATE the correct remote for the motor
-
If using the Ysia 5 Channel remote, PRESS the Channel Selector button to choose the correct channel
-
PRESS & HOLD the motor or paired remote Programming Button for 3 seconds until the motor jogs once
-
While nearby the motor, BRIEFLY PRESS the UP and DOWN buttons on the remote
NOTE: This activates Scanning Mode to establish a link with the motor.
The motor LED will stop blinking AMBER when the link starts, followed by the remote LED flashing GREEN twice.
Then the motor LED will blink GREEN and goes off, the motor jogs once to confirm the link. The remote LED will continue to blink AMBER while in Programming Mode.
Setting Upper/Open Limits -
PRESS & HOLD the UP or DOWN buttons to move the motor to the desired upper or open limit
-
BRIEFLY PRESS the MY and DOWN buttons until the motor jogs once to confirm the new upper limit Setting Lower/Closed Limits
-
PRESS & HOLD the UP or DOWN buttons to move the motor to the desired lower or closed limit
-
BRIEFLY PRESS the MY and UP buttons until the motor jogs once to confirm the new lower limitRepeat steps 6-9 until the correct limit positions are established.
Exit Limit Adjustment Mode -
PRESS & HOLD the remote UP and DOWN buttons for 5 seconds until the remote Status LED stops flashing GREEN
OR
BRIEFLY PRESS the remote Programming Button, WAIT for the motor to jog once
[APPENDIX B] FACTORY RESET
Ysia Remote Factory Reset
NOTE: Performing a factory reset on a Ysia remote does not affect the
motor limits and programming. The remote configuration is irrecoverable after
performing a Factory Reset; all settings will return to default, removing all
motors and settings.
-
FIND the remote control to be reset
NOTE: The remote settings are not recoverable once the factory reset is complete. -
PRESS & HOLD the Programming Button on the remote until the LED blinks RED 3 times
NOTE: This process takes approximately 15 seconds. -
RELEASE the Programming Button and CONFIRM the long blinking AMBER LED
NOTE: The remote is in Programming Mode for 3 minutes.
Factory reset is complete.
NOTE: If motors are paired, they will jog, leave the network, and enter
Programming Mode for 10 minutes.
Motor Factory Reset
NOTE: Performing a factory reset on motors will remove all settings (end
limits, speeds settings, network pairings) and return product to the default
state.
The motor settings are irrecoverable after performing a Factory Reset.
-
LOCATE the motor to be reset
NOTE: The motor settings are not recoverable once the factory reset is complete. -
PRESS & HOLD the Programming Button on the motor until the motor jogs 3 times
NOTE: This process takes approximately 15 seconds. -
RELEASE the Programming Button and WAIT for the blinking AMBER LED on the motor head. The motor will go into Programming Mode for the next 3 minutes and is ready for pairing.
Factory reset is complete after the motor jogs 3 times.
The motor will go into Programming Mode for 3 minutes after the motor is
reset, ready for pairing.
FOR QUESTIONS OR ASSISTANCE PLEASE CONTACT TECHNICAL SUPPORT:
(800) 22-SOMFY (76639)
technicalsupport_us@somfy.com
About Somfy®
For over 50 years, Somfy has been pioneering innovative motorization and
automated solutions for window coverings and exterior shading products. With
comfort, ease of use, security, and sustainability in mind, our seamless and
connected solutions are designed to help people make the move to living
spaces impactful for humans and with a reduced impact on nature.
New Jersey
121 Herrod Blvd.
Dayton, NJ 08810
T: (800) 22-SOMFY
F: 609-395-1300
Somfy Systems, Inc.
T: (800) 22-SOMFY
www.somfypro.com
Florida
1200 SW 35th Ave.
Boynton Beach, FL 33426
T: (877) 22-SOMFY
F: 561-995-7502
California
15301 Barranca Parkway
Irvine, CA 92618-2201
T: (877) 72-SOMFY
F: 949-727-3510
Somfy ULC
T: (800) 66-SOMFY
www.somfypro.ca
6411 Edwards Blvd
Mississauga, ON L5T 2P7
CN: (800) 66-SOMFY
F: 905-564-6446
©Somfy Systems, Inc.• JUN E2023
Allbrands, products, and trade marks areth eproperty of the irrespective
owners.
PS- PG 16
V 1 .0 Make the move
Documents / Resources
|
somfy Sonesse 30 24V DC
Zigbee
[pdf] User Guide
Sonesse 30 24V DC Zigbee, Sonesse 30, 24V DC Zigbee, DC Zigbee, Zigbee
---|---
References
- Home page - us
- Home page new - ca
- Home page new - ca
- Home page - us
- Home page - us
- Help Me App - us
- Somfy U
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>