xmartO Wireless Light Bulb Camera User Guide

: June 17, 2024
: xmarto

Wireless Light Bulb Camera

QUICK SETUP GUIDE

1. What’s in the Box

DISCLAIMER: The exact components of your camera, images and quantities may vary depending on your model number. While these may vary, this QSG will address the setup of your camera.

2. Working Diagram

2.1 Works Standalone

2.2 Works as an Add-on Cam

3. Camera Introduction

NOTE : The actual appearance and components may vary with different model of product.

4. Set up the Camera

Preparation: Download and Install the App

1. Download the Wall Pixel App from the App Store or Google Play Store and install it on your smart device.

You can scan the QR code to find the App.

2. Create an user account and login. Tap the + symbol to add a device.

Set up the Camera

4.1 Set up the Camera

1. Bring the camera near to your router, plug it to power with included plug- in E27 adapter, or screw the light bulb camera to your lamp socket. The camera will start to run and enters to configuration mode.

Configuration mode sign: constant beeps and LED indicator flashes.

2. In App, tap + on top right, then tap Add. Choose your camera type.

3. Follow on-screen guide, select your home Wi-Fi (2.4G) and input your Wi-Fi password, the App will generate a QR code of your Wi-Fi information.

NOTE: The camera works with 2.4G Wi-Fi only.

4. Use the camera lens to scan the QR code on screen till you hear a prompt tone. Tap “Heard the prompt tone” when you hear it.

NOTE: The QR code will be generated and displayed on your phone. Please hold your phone in front of the camera at a distance of about 20cm (8 inches) and have the phone face the camera lens to let the camera scan the QR code.

5. Then follow the on-screen steps to complete setting up the camera.

NOTE: If the camera was not added successfully, hold the reset button to reset and try again. Make sure to provide CORRECT Wi-Fi hotspot and password.

4.2 App Live View

apps screen

5. Install a SD Card

Install the Micro SD Card (Optional)

Install a micro SD card to the camera for recording. (8~512GB SD Card)

Remove the cover on the camera.
Insert a Micro SD card into the card slot. (SD card not included)
Place the cover back on.

NOTE : After the Micro SD card installed, please go to App – Camera’s Settings to format the SD card to start recording.

6. Install the Camera

Install the camera 2-3 meters (7-10 ft) above the ground. This height maximizes the detection range of the motion sensor.
For dome cameras, they MUST be installed upside down for better waterproof performance and better motion sensor’s efficiency.
For better motion detection performance, please install the camera angularly.

Installation Tips

Do not face the camera towards any light sources.
Do not point the camera towards a glass window. Or, it may result in poor image performance due to the window glare from infrared LEDs, ambient lights or status lights.
Do not place the camera in a shaded area and point it towards a well-lit area. Or, it may result in poor image performance. For better image quality, please make sure that the lighting condition for both the camera and the captured object is the same.
For better image quality, it’s recommended to clean the lens with a soft cloth regularly.
Make sure the power ports are not exposed to water or moisture or blocked by dirt or other elements.
Do not install the camera in places where rain and snow may hit the lens directly.
The camera may work in extremely cold conditions as low as -25°C as it will produce heat when powering on. You may power on the camera indoors for a few minutes before installing it out- doors.

7. Pair the Camera to XMARTO NVR

The camera works standalone. It can also work as an add-on camera. You can add it to your existing XMARTO NVR or system.

1. Bring the camera close to the NVR and plug it to power with included power adapter. Your camera will start run and enters to configuration mode soon.

Configuration mode: constant beeps and LED indicator flashes

2. You can now start pairing the camera to NVR.

For NVR version 3.4 or earlier

Run Add Cam by WiFi on NVR monitor and follow on-screen instructions to add the camera to NVR.

For NVR version 3.5+

Click the + icon and follow on-screen instructions to add the camera to NVR.

3. Once the camera is added to the NVR, you’ll see it displays video on the monitor. You can then go ahead to mount the camera.

NOTE: Please mount the camera within NVR’s WiFi range.

4. If you failed to add the camera to NVR, hold the camera reset button for about 10 seconds to reset the camera, then pair it to the NVR once again.

8. Zoom

How to Use the 10x Hybrid Zoom?

1. When the camera works standalone, you can zoom in the pictures from the app.

In the WallPixel app, tap the device to enter live view. Next to the PTZ control, you can see the zoom in/out bar, slide up and down to zoom in and out.

2. When the camera works with NVR, you can zoom in from both the NVR and the Wall Pixel app

On NVR screen, click on the camera view to pop out the sub-menu, then click PTZ Control icon to enter PTZ control inter- face. Then click “+ –” next to Zoom to zoom in/out the pictures.

In the WallPixel app, tap the device to enter live view. Then tap Pro to pop out the zoom bar. Tap + to zoom in and – to zoom out.

9. Troubleshooting

Pan Tilt is not Working?
If the pan tilt is not working, please try the following solutions:

Power cycle the camera and see if the pan tilt works again.
Calibrate the camera, as shown in below figure.
Make sure your camera has at least 3-bar WiFi signal.
Reset the camera and setup again.

Camera does not Power on

If your camera does not power on, please try the following solutions:

Camera only supports one power extension cable, do not use two extension cables.
Plug the camera into a different outlet and see if it works.
Power on the camera with another working power adapter and see if it works.

IR LEDs Stop Working

If you find the IR LEDs of your camera stop working, try the following solutions:

Please go to Live View and check the night vision mode. Set the mode to Auto to activate the IR lights.
Upgrade your camera’s firmware to the latest version.
Restore the camera to the factory settings and check the IR light settings again.

If you need further help, please contact XMARTO Support via email support@xmarto.com

10. Notification of Compliance

FCC Compliance Statement

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Limited Warranty

This product comes with a 1-year limited warranty that is valid only if purchased from XMARTO official stores or a XMARTO authorized reseller.

NOTE : We hope that you enjoy the new purchase. But if you are not satisfied with the product and plan to return, we strongly suggest that you reset the camera to factory default settings and take out the inserted SD card before returning.

Terms and Privacy

Use of the product is subject to your agreement to the Terms of Service and Privacy Policy at xmarto.com. Keep out of reach of children.

End User License Agreement

By using the Product Software that is embedded on the XMARTO product, you agree to the terms of this End User License Agreement (“EULA”) between you and XMARTO.

ISED Radiation Exposure Statement (For WiFi Version)

This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

CONTACT US

Email: support@xmarto.com

Website:
24/7 Product Support
FAQs
How-to Videos
Manuals
www.xmarto.com

iPhone, iPad, Mac and Mac OS X are registered trademarks of Apple Inc.

Windows, Windows XP, Windows Vista, Windows 7, Windows 8 and Windows 10 are registered trademarks of Microsoft Corporation in theUnited States and/or other countries.

FCC RADIATION NORM

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Compliance Statement

These limits are designed to provide reasonable protection against frequency interference in residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed or used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in television reception, which can be determined by turning the equipment off and on. The user is encouraged to try and correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

CAUTION!

The Federal Communications Commission warns the user that changes or modifications to the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment should be installed and operated with a minimum distance of 8 inches between the radiator and your body.