baby trend JP02E45A My First Jumper Instruction Manual
- June 17, 2024
- baby trend
Table of Contents
Read all instructions BEFORE assembly
and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
My First Jumper
Instruction Manual
JP02xxxA 6m+
JP02E45A My First Jumper
WARRANTY
DO NOT RETURN YOUR PRODUCT TO THE STORE. PLEASE CONTACT BABY TREND® FOR
REPLACEMENT PARTS, SERVICE AND REPAIR.
The Baby Trend® warranty covers workmanship defects within 1 year of purchase.
Any product which has been subjected to misuse, abuse, abnormal use, excessive
wear and tear, improper assembly, negligence, environmental exposure,
alteration or accident, or has had its serial number altered or removed
invalidates all claims against the manufacturer. Any damage to property during
installation is the sole responsibility of the end user. Customer Service
Department can be contacted at 1
800-328-7363 Monday through Friday
between 8:00 a.m. and 4:30 p.m. (PST). Return Authorizations are required
prior to returning product(s) to Baby Trend®. Please visit
http://babytrend.com/pages/limited-warranty for complete warranty details.
Baby Trend, Inc. 13048 Valley Blvd. Fontana CA 92335
1-800-328-7363 • (8:00am ~ 4:30pm PST)
www.babytrend.com
WARNING
Read al Instructions before assembly and use stationary a jumper.
instructions for future seb not use the stationary activity jumper if it is
damaged or broken.
IMPORTANT SAFETY INFORMATIONS
Use the activity jumper ONLY if the child meets ALL tte requirements below:
- Only for use by infants at least 6 months old and who can hold their head up unassisted.
- ls less than 32’ tall (81.2cm).
- Weighs less than 26.5 Ibs. (12kg).
FALL HAZARD!
Babies can FALL from product resulting in head injuries.
- Never leave child unattended. Always keep child in view while in product.
- Never use near stairs.
- To avoid tip over, place the activity jumper on a flat, level surface.
- Discontinue to use this product if child can climb out or begins to walk.
STRANGULATION HAZARD!
Strings can cause STRANGULATION.
- DO NOT place items with a string around child’s neck, such as hood strings or pacifier cords.
- DO NOT suspend strings over product or attach strings to toys.
- DO NOT place the activity jumper on an elevated surface.
- A child’s movement can slide the activity jumper.
- DO NOT allow children who can stand or walk on their own to sit in the seat of the activity jumper.
- Never move the activity jumper while the child is in the seat.
- DO NOT swing or spin child in activity jumper.
- DO NOT use activity jumper
- DO NOT use any hardware or parts other than that supplied.
- Examine product frequently for damaged, missing, or loose parts.
- DO NOT use activity jumper if damaged or broken. This product contains small parts. Requires an adult for assembly.
CARE AND CLEANING
Fabric Seat – Machine wash the fabric seatin cold water.
Use a gentle wash cycle with no bleach.
Air or line dry.
Plastic Parts — Wipe clean with damp cloth and mild soap.
Air Dry. DO NOT immerse in water.
IMPORTANT! To ensure safe operation of your product, please follow these
instructions carefully. Please keep these instructions for future reference.
IMPORTANT! Before assembly and each use, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges. NEVER use if any parts
are missing or broken.
IMPORTANT! Adult assembly is required. Keep child away during unpacking
and assembly.
CUSTOMER SERVICE
The Customer Service Department can be contacted at 1
800-328-7363 Monday through Friday
between 8:00 a.m. and 4:30 p.m. (PST).
Return Authorizations are required prior to returning product(s) to Baby
Trend®.
Check that you have all the parts for this model.
*Alltoys can be used with or without the tabletop.
Connecting the Bars
Connect all 3 curved frames ntil it clicks in as shown (Fig. 1a).
Standing bar (1) showing no empty hole at the top should be placed first.
Standing bars (2) and (3) with empty holes located at the top should be in
this order as shown (Fig. 1b).
NOTE: Ensure all 3 pins click in.
Insert each hanging arch at the top of the standing bars (2) and (3) as shown (Fig. 1c).
Activity Tabletop Setup
Insert the ends of the anchor strap through each slot of the table as shown
(Fig. 2a & 2b).
Once the strap is threaded through, pull on the end of the tab to make sure
it’s secured (Fig. 2c).
NOTE: Ensure to anchor underneath by pulling the strap back so the anchor
tab is secure (Fig. 2d).
Adjustment Strap
The strap has 3 adjustable height levels. ALWAYS adjust all the straps to the
SAME LEVEL (Fig. 2c).
Use level 3 to place the platform in the highest position, level 2 for middle
position and level 1 for the lowest position (Fig. 2d).
NOTE: Always use the level that is most suitable for your child’s height.
NOTE: To adjust the straps, unhook the adjustment plate from the small strap and re-adjust to the appropiate height (Fig. 2e). DO NOT leave the adjustment plate hanging (Fig. 2f).
Swivel Seat Mode
To assemble the seat pad and seat ring, see (Fig. 7b).
Align the seat to the center opening and press it down firmly. The seat must
completely click into to the tabletop (Fig. 3a).
NOTE: Rotate the seat to ensure the swivel function is active.
Ensure your child’s toes are touching the floor (Fig. 3b). Adjust the height to the correct level if your child’s feet are either fully touching the floor OR if the toes are not touching the floor at all. Refer to (Fig. 2d).
WARNING:
- Requires three AAA (LRO3) batteries (not included) for toy operation.
- Non-rechargeable batteries are not to be recharged.
- Different types of batteries or new and used batteries are not to be mixed. Batteries need to be inserted with the correct polarity.
- Exhausted batteries are to be removed from the toy.
- The supply terminals are not be short-circuited.
- Rechargeable batteries are to be removed from the toy before being charged.
- Rechargeable batteries are only to be charged under adult supervision.
Toy Electronics
Battery Instructions
The Lights and Sounds Animal Toy requires 3 AAA batteries. Reference the
diagram for battery installation. Unscrew the battery door and pull outward.
Install batteries as shown. Secure battery door with screw.
Toy Attachments
Place toys in this order as shown. Toys must be properly attached before use, in their designated housing (Fig. 5a).
Flower Toy : Assemble the (3) pieces together as shown (Fig. 5b).
For the top cap piece, ensure to check underneath the cap. The 3 clips should
match with the slots.
The 4 inner holes must match with the pins as shown (Fig. 5c).
Single Tab Toys
Toys must be aligned with their single tab housings on the tabletop (Fig. 5d).
Set each toy into the fitting and underneath the tabletop push the lock up and
turn it to lock (Fig. 5e).
NOTE: Do not use double tab toys on single tab fitting.
Double Tab Toys
Toys must be aligned with their double tab housings on the tabletop. Set each
toys into the fitting and underneath the tabletop push the lock up and turn it
to lock (Fig. 5f).
NOTE: Do not use single tab toys on double tab fitting.
Toy Alignment Diagram
Use the diagram below as a reference of the single and double tabs, toy
fittings and locking tabs. Always put the small tab lock back into the
tabletop when not in use.
Hanging Toys
Hook to clip: If required use the toy strap to insert it into the front side
of the clip (Fig. 5g).
Attach the hanging toys over the two hanging arches as shown (Fig. 5h).
Disassembling the Jumper
Seat Removal
Ensure all the toys are removed.
To remove the seat, use the edge of the seat to lift it off the tabletop (Fig.
6a).
Strap Removal / Replacement
If replacement is needed for the strap, cut the strap with scissors (Fig. 6b).
To re-thread the new strap, repeat Fig. 2a.
Frame Removal
When replacing the strap, the standing bar must be removed (Fig. 6¢). To re-
assemble the bar, repeat steps Fig. 1b through Fig. 2f
Seat Fabric
DO NOT MACHINE WASH.
For metal and plastic parts, use only lukewarm water and mild soap.
To remove the seat fabric for maintenance, pull out all the plates from the
tab on the seat base (Fig. 7a).
To reattach the fabric, insert the warning label side towards the of the seat base. Fold the fabric over and insert the rear center plate into the tab. Continue to connect all plates around the seat base tabs. All plates and tabs must be secured before use (Fig. 7b).
Maintenance and Cleaning
Check this product regularly before using it, and do not use it if any part is
loose or missing or if there are any signs of damage. Do not substitute parts.
Contact the manufacturer if replacement parts or additional instructions are
needed.
Clean this product after each use, using mild household dish soap. Please use
only a soft bristle brush, sponge or cloth to clean the surface or remove
particles of food.
DO NOT submerge the product in water. Surface clean only.
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interfer- ence that may cause undesired operation.
AWARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Baby Trend, Inc.
13048 Valley Blvd.
Fontana CA 92335
1-800-328-7363
(8:00 a.m. ~ 4:30 p.m. PST)
www.babytrend.com
JP02XXXA_2L_010224
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>