General Aire ASG1207U12MI-KM USB C Headphones Wired Instruction Manual

General Aire ASG1207U12MI-KM USB C Headphones Wired

Specifications

• Model: [Insert Model Name]
• Type: Wall-mounted Air Conditioner
• Part Number: 9387858150-01
• Refrigerant Type: R32

Product Usage Instructions

Safety Precautions
Before using the air conditioner, it is crucial to follow these safety precautions:

• WARNING: This mark indicates potential risks of death or serious injury.
• CAUTION: This mark warns of possible injury or property damage.
• PROHIBITED: Denotes actions that are not allowed.
• COMPULSORY: Denotes actions that are required.

Preparation
Prior to using the air conditioner, make sure to perform the following preparation steps:

• WARNING: Check the refrigerant type mentioned on the rating label.
• CAUTION: Verify the amount of refrigerant charge based on the room area as per the table provided.
• Indoor Unit Accessories: Ensure that the remote controller, remote controller holder, self-tapping screws, batteries, and air cleaning filters are included.

Name of Parts
Refer to the user manual for a detailed description of each part and its function.

SAFETY PRECAUTIONS

To prevent personal injury or property damage, read this section carefully before you use this product, and be sure to comply with the following safety precautions.
Incorrect operation due to failure to follow the instructions may cause harm or damage, the seriousness of which is classifi ed as follows:

WARNING
This mark warns of death or serious injury.

CAUTION

• This mark warns of injury or damage to property.
• This mark denotes an action that is PROHIBITED.
• This mark denotes an action that is COMPULSORY

WARNING

• This product contains no user-serviceable parts. Always consult authorized service personnel for repairing, installation, and relocation of this product. Improper installation or handling will cause leakage, electric shock, or fi re.
• In the event of a malfunction such as burning smell, immediately stop operation of the air conditioner, and disconnect all the power supply by turning off the electrical breaker or disconnecting the power plug. Then consult authorized service personnel.
• Take care not to damage the power supply cable. If it is damaged, it should be replaced only by authorized service personnel in order to avoid a hazard.
• If a refrigerant leakage is suspected, all naked fl ames shall be removed or extinguished, and consult authorized service personnel.
• In the event of a thunder storm or any prior sign of a lightning strike, turn off the air conditioner via the remote controller, and refrain from touching the product or the power source to prevent any electrical hazards.
• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of this product by a person responsible for their safety. Children should be supervised to ensure that they do not play with this product.
• Dispose of the packing materials safely. Tear and dispose of the plastic packing bags so that children cannot play with them. There is danger of suff ocation if children play with the original plastic bags.
• Do not start or stop the operation of this product by inserting or pulling out the power plug, or by turning on or off the circuit breaker.
• Do not use fl ammable gases near this product.
• Do not expose yourself directly to the cooling airfl ow for many hours.
• Do not insert your fingers or any other objects into outlet port or inlet port.
• Do not operate with wet hands.

CAUTION

• Provide occasional ventilation during use.

• Always operate this product with air fi lters installed.

• Ensure that any electronic equipment is at least 1 m (40 in) away from this product.

• Disconnect all the power supply when not using this product for extended periods.

• After a long period of use, ensure to get the mounting of the indoor unit checked to prevent this product from falling down.

• The airfl ow direction and the room temperature should be carefully considered when you use this product in a room with infants, children, elderly or sick persons. Keep the surroundings of the outdoor unit clean and tidy, and do not place items around it. Any objects blocking or entering from the outlet ports may cause product malfunction.
  Do not direct the airfl ow at fi replaces or heating apparatus.

• Do not block or cover the intake grille and the outlet port.

• Do not apply any heavy pressure to the radiator fi ns.

• Do not climb on, place objects on, or hang objects from this product.

• Do not place any other electrical products or household belongings under this product. Dripping condensation from this product might get them wet and may cause damage or malfunction of your property.

• Do not expose this product directly to water.

• Do not use this product for the preservation of food, plants, animals, precision equipment, artwork, or other objects. This may cause quality deterioration of those items.

• Do not expose animals or plants to direct airfl ow.

• Do not drink the drainage from the air conditioner.

• Do not pull the power supply cable.

• Do not touch the aluminum fi ns of the heat exchanger built-in this product to avoid personal injury when you maintain the unit.

• Do not stand on unstable steps when operating or cleaning this product. It may overturn and can cause injury.

This product contains fluorinated greenhouse gases.

For R32 refrigerant model
To check the refrigerant type of your product, refer to the rating label.

WARNING
The appliance shall be installed, operated and stored in a room with a fl oor area larger than X m².

• This product shall be stored in a room without continuously operating ignition sources (for example: open fl ames, an operating gas appliance or an operating electric heater).
• This product shall be stored in a well-ventilated area.
• Be aware that refrigerants may not contain an odour.
• This product shall be stored so as to prevent mechanical damage from occurring.
• Disposing of the product shall be done properly, in compliance with national or regional regulations.
• During transportation or relocation of the indoor unit, pipes shall be covered with the wall hook bracket for protection.
• Do not move this product by holding the indoor unit pipes.(The stress applied to the pipe joints may cause the fl ammable gas to leak during operation).
• Do not install the unit in area fi lled with mineral oil such as a factory or area containing a large amount of splashed oil or steam such as a kitchen.
• Do not use means to accelerate the defrosting process or to clean this product, other than those recommended by the manufacturer.
• Do not pierce or burn.

Explanation of symbols displayed on the indoor unit or outdoor unit.

PREPARATION

WARNING

• Take care to prevent infants and young children from accidentally swallowing the batteries.

CAUTION

• If leaking battery fl uid comes in contact with your skin, eyes, or mouth, immediately rinse with plenty of clean water, and consult your physician.
• Exhausted batteries must be removed immediately, and be disposed according to the local laws and regulations of your region.
• Do not attempt to recharge dry batteries.
• Do not use dry batteries that has been recharged

NAME OF PARTS

CAUTION
For appropriate signal transmission between the remote controller and the indoor unit, keep the signal receiver away from the following items:

• Direct sunlight or other strong lights
• Flat-panel television screen
  In rooms with instantaneous fluorescent lights, such as inverter-type ones, the signal may not be transmitted properly. In such a case, consult the store of purchase.

Indoor unit

1. Before starting the operation, make sure that the intake grille is closed completely. Incomplete closing may aff ect the proper function or performance of the product.
2. Indicator lamps light in the following conditions.

Remote controller

When you use the optional remote controller, the appearance and the operation procedure may diff er.
For details, refer to the operation manual of each remote controller.

Signal transmitter
Aim at the signal receiver of the indoor unit properly.

• The operating range is approximately 7 m.
• will appear when the signal is transmitted.
• The indoor unit will emit a beep when it receives the signal properly. If there is no beep, press the button again.

Remote controller display
In this section, all the possible indicators are displayed for description.
In actual operation, the display is linked with the button operation, and only shows the necessary indicators for each setting

CAUTION

• To prevent malfunction or damage of the remote controller:
• Place remote controller at where will not be exposed to direct sunlight or excessive heat.
• Remove batteries if the product is not going to be used for an extended period.
• Obstacles such as a curtain or wall between the remote controller and the indoor unit may aff ect the appropriate signal transmission.
• Do not apply strong shocks to the remote controller.
• Do not pour water on the remote controller.

Inserting batteries

Battery type: R03/LR03/AAA x 2

1. Pull the cover in the direction of the arrow and open it until it is trapped.

2. Remove the cover.

3. Turn the remote controller over and push the back side of the cover and remove the claws by curving the cover.

4. Pull in the direction of the arrow while curving the cover.

5. Put batteries as shown in the figure above.

6. Press as shown in the figure above.
   Use the tip of a ballpoint pen or other small object.

7. Press to start the clock setting.

8. Press to set the clock.

   • Press the buttons to change the clock by a minute.
   • Press and hold the buttons to change the clock by 10 minutes.
   • To switch the time indicator (12-hour ⇔ 24-hour ), press

9. Press to complete the setting.

10. Install and close the cover.

NOTES

• Use the specified type of batteries only.

• Do not mix different types or new and used batteries together.

• Batteries can be used for about 1 year in ordinary use.

• If the remote control range noticeably shortens, replace the batteries and press as shown in the figure above.

• In the Cooling or Dry mode, set the temperature lower than the current room temperature.
  In the Cooling mode, the indoor unit fan may stop from time to time to perform Fan control for energy saving that enables power-saving operation by stopping the rotation of the indoor unit fan when the outdoor unit is stopped.
  In the initial setting, this function is activated.
  To deactivate the function, consult the installer or authorized service personnel.

• In the Heating mode,

  • set the temperature higher than the current room temperature.
    at the beginning of the operation, the indoor unit fan rotates at a very low speed for 3 to 5 minutes.
    the Automatic defrosting operation overrides the Heating operation when necessary.

• In the Fan mode, temperature control is not available.

BASIC OPERATIONS

3 steps to start operation

1. Press to start or stop the operation.

2. Press to select the operation mode.
   The operation mode changes as follows.
   

3. Press to set the desired temperature.
   The temperature changes by 0.5°C increments.

Temperature setting range

• Auto/Cooling/Dry 18.0°C to 30.0°C
• Heating 16.0°C to 30.0°C

Temperature unit switching

1. If the air conditioner is operating, press to stop the operation.

2. Pres s and hold for more than 5 seconds.
   The current temperature unit will be displayed. (Factory setting: °C)

3. Press to switch the temperature unit. (°C ⇔ °F)

4. Press to fi nish the setting.
   If you do not press the button for 30 seconds, the displayed temperature unit will be set.

AIRFLOW SETTINGS

Fan speed setting

Press Fan to control the fan speed.
The fan speed changes as follows.

Airfl ow direction setting For details of the airfl ow ranges, refer to “Airfl ow direction range.”

• Up/down airfl ow direction setting
  • Press to adjust the up/down airfl ow direction.
• Left/right airfl ow direction setting

CAUTION
Before you adjust the left/right airfl ow direction, make sure that the horizontal louver has been stopped completely.

• Adjust two knobs by hand.
• Swing operation setting

Press to start/stop the Swing operation.
NOTE: The Swing operation may stop temporarily when the indoor unit fan is rotating at a very low speed or is stopped

Airfl ow direction range
Up/down airfl ow direction

The Swing operation range depends on the airfl ow direction set before the Swing operation.

NOTES

• Do not adjust the airfl ow direction louvers by hand.

• In the Auto or Heating mode, the airfl ow direction stays position 1 for a while from the start of the operation.
  In the Cooling or Dry mode, the downward airfl ow can change to the upper as follows. This feature is to prevent condensation from dripping and damaging your property.
  Condition: Position 4-6 keeps for 30 minutes
  Airfl ow adjusted to: Position 3

• When using the mobile app, the up/down airfl ow can be selected from 4 positions.

TIMER OPERATIONS

NOTE: When [ ] indicator on the indoor unit blinks, set the clock and timer again. This blinking shows that the internal clock goes wrong due to an interruption of the power supply.

On timer or timer

The On timer starts the operation at your desired time.
The Off timer stops the operation at your desired time.

1. When you use the On timer, press ON .
   When you use the Off timer, press OF .

2. Press ( ) to set on time or off time.

• Pressing the button: The time will change by +5/-5 minutes.
• Pressing and holding the button: The time will change by +10/-10 minutes.
•  To deactivate the On/Off timer, press while is shown on the remote controller display.

The indicator will disappear.
NOTE: If you set the Sleep timer after setting the On timer or Off timer, the On timer or Off timer is canceled.

Program timer
The Program timer operates as a combination of the On timer and Off timer.

1. Set On timer and Off timer. (Refer to “6.1. On timer or Off timer”).
   • The timer setting changes to the Program timer automatically.

The timer whose setting time is closer to the current time works first.
The order of the timer operation is displayed as follows:

NOTES

• You can set the Program timer only within a span of 24 hours.
• If you set the Sleep timer after setting the Program timer, the Program timer is canceled.

Sleep timer
The Sleep timer supports your comfortable sleep by moderating the air conditioner operation gradually.

1. Press .
   2. Press ( ) to set the time until the operation stops.

Each time you press the button, the time changes as follows:

NOTE: If you do not press any buttons for 5 seconds, the remote controller display returns to the standby screen.

• The setting time is kept even if the Sleep timer finishes. To repeat the Sleep timer, press while is not shown on the remote controller display.
• To deactivate the Sleep timer, press while is shown on the remote controller display.

The indicator will disappear.
During the Sleep timer operation, the setting temperature changes as the following figure.

After the set time has elapsed, the air conditioner operation turns off .
NOTE: If you set the On timer or Off timer after setting the Sleep timer, the Sleep timer is canceled.

ENERGY SAVING OPERATION

Economy operation
It saves more electricity than other operation modes by changing the set temperature to a moderate setting.
Press to activate/deactivate the Economy operation.
indicator on the indoor unit will turn on.

NOTES

• In the Cooling, Heating, or Dry mode, the maximum output of this operation is approximately 70% of the usual operation.
• This operation cannot be performed during the temperature monitoring by the Auto mode.

 OTHER OPERATIONS

Powerful operation
In the Powerful operation, the air conditioner will operate at maximum power and strong airflow to cool down or warm up the room quickly.

NOTE: In the multi-split connection, this function cannot be used.

• Press to activate/deactivate the Powerful operation.
• When activated, the indoor unit will emit 2 short beeps.
• When deactivated, the indoor unit will emit 1 short beep.

The Powerful operation will be turned off automatically in the following situations:

• The Powerful operation runs for a certain amount of time, and the room temperature reaches the set temperature in the Cooling, Dry, or Heating mode.
• 20 minutes after the Powerful operation has started.

NOTES

• The airflow direction and the fan speed are controlled automatically.
• The Powerful operation cannot be performed simultaneously with the Economy operation.
• The Powerful operation overrides the following operations. If the following operations are set, they will start after the Powerful operation finishes.
• Outdoor Unit Low Noise operation
• If the wired remote controller (optional) is connected, this function is restricted.

Outdoor Unit Low Noise operation
The Outdoor Unit Low Noise operation lowers noise from the outdoor unit. During this operation, the rotation number of the compressor decreases, and the outdoor unit fan rotates slowly.

• NOTE: In the multi-split connection, this function cannot be used.
• Press to activate/deactivate the Outdoor Unit Low Noise operation.
• While the Outdoor Unit Low Noise operation is activated, on the remote controller is displayed.
• The setting is preserved even if the air conditioner is turned off .

NOTES

• This operation cannot be performed simultaneously with the Fan mode, Dry mode, and Powerful operation.
• If the wired remote controller (optional) is connected, this function i restricted.

10°C Heat operation
10°C Heat operation maintains the room temperature at 10°C so as to prevent the room temperature from dropping too low.

• Press to activate the 10°C Heat operation.
• The indoor unit will emit 1 short beep and [ ] indicator on the indoor unit will turn on.
• Press to turn off the air conditioner.
• [ ] indicator will turn off .

NOTES

• During the 10°C Heat operation, only is valid.
  When the room temperature is warm enough, this operation will not perform.

• If the wired remote controller (optional) is connected, this function is restricted.

WLAN control

This operation manual describes only the setting procedure of the remote controller.
For how to operate the mobile app, refer to the operation manual of the mobile app.

NOTES

• The air conditioner settings from the mobile app will not be refl ected in the wireless remote controller.
• It will not be possible to operate and monitor by the mobile app while the power supply of the air conditioner is disconnected (via breaker or plug).
• The room temperature will be displayed in the mobile app during operation. However, the displayed room temperature may not be correct depending on the situation in the room or the air conditioner operating status. Use this only as a reference.
• If the mobile app and remote controller settings diff er, the latest operation performed will take priority.
• If timer settings are done from the mobile app and from the wireless or wired remote controller, both timer settings will be active.

The contents of wireless LAN label are necessary for wireless LAN setup.
Write down the SSID and the PIN code to the following table.

Open the intake grille.

*The layout of the wireless LAN label may diff er by the part or model. Information on WLAN adapter

• AIRSTAGE Mobile” is a trademark of FUJITSU GENERAL LIMITED.
• Android and Google Play are registered trademarks of Google LLC.
• App Store is a service mark of Apple Inc., registered in the U.S. and other countries.
• IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.
• QR Code” is a registered trademark of DENSO WAVE INCORPORATED.

Usage precautions

Usage precautions for wireless LAN control

• WARNING
• Do not repair, disassemble or remodel the WLAN adapter.
• Do not get the WLAN adapter wet or use it in locations with lots of moisture.
• Do not operate with wet hands.
• Do not install the WLAN adapter in locations where the use of wireless equipment is prohibited (e.g., hospitals).
• Do not use the WLAN control near persons with a pacemaker or similar devices.
• Do not use the WLAN control near automatic control equipment (e.g., automatic doors and fi re alarms).

CAUTION
When cleaning the air conditioner, be sure to stop the operation and turn off the power. Otherwise, there is a risk of electric shock or injury.

• Do not stand on slippery, uneven, or unstable surfaces when install the WLAN adapter.
• Do not put fi ngers, sticks, etc., in the connection part of the WLAN adapter and the insertion slot of the air conditioner.
• The WLAN adapter is not a USB device. Do not connect to other than specifi ed equipment. Otherwise, there is a risk of malfunction or fi re.
• When you use the WLAN control, it will become possible to operate the air conditioner from locations where you cannot see it directly. This means that people in the room may be exposed to the unintended operation of the air conditioner. Check the condition of the room before using the WLAN control.
• Be sure to check regularly that dust has not built up around the connection slot of the air conditioner for the WLAN adapter.
• Be sure to check in advance that there are no malfunctions of the air conditioner.
• Make sure that the airfl ow from the air conditioner will not cause any adverse eff ects.
• Objects may fall down causing personal injury, fi re, or damage to property.
• If you know that there are people in the vicinity of the air conditioner, inform them in advance that you will operate it from a distant location. Sudden operation of the air conditioner may surprise a person and cause the person to fall down or tumble if the person is on a step, ladder, etc. Furthermore, rapid changes of the room temperature may cause deterioration in a person’s physical condition. Do not use the WLAN control when there are people in the room who are not able to control the temperature by themselves (For example,  infants, children, those with physical disabilities, elderly or sick persons.).
• Fully understand the reserved timer settings and other operations before using the WLAN control.
• Unexpected operation of the air conditioner may cause deterioration in a person’s physical condition or an adverse eff ect on animals or plants.
• Frequently check the settings and operating situation of the air conditioner when using the WLAN control from a distant location.
• Rapid changes of the room temperature may cause deterioration in a person’s physical condition or an adverse eff ect on animals or plants.
• If you operate the air conditioner by the WLAN control, the indicator lamps and reception sounds of the air conditioner do not work.
• If there is bad reception between the WLAN adapter and the access point, adjusting the access point position or direction of the antenna may improve the reception. It may also be possible to improve reception by moving the access point closer to the WLAN adapter or using a wireless
• LAN repeater.
• Radio wave and security precautions
• When you use a wireless LAN, there are precautions that you must follow in relation to radio waves, personal information, and so on. To use the WLAN control correctly, be sure to read the following precautions and the operation manual of the wireless LAN equipment you are using. We
• will assume no responsibility, unless legal liability is recognized, in regards to failures, other defects and damages incurred by use of the WLAN adapter that occur through incorrect use or during use by yourself or a third party.
• Radio wave usage precautions

CAUTION

• Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
•  This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20 cm or more away from person’s body.(UTY-TFSXH3 [AP-WH3E]/UTY-TFSXH4 [AP-WH4E] model conforms to IC (Industry Canada) standard.)

NOTES

• This device complies with Part 15 of FCC Rules and Industry

Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of this device.

(UTY-TFSXH3 [AP-WH3E]/UTY-TFSXH4 [AP-WH4E] model conforms to IC (Industry Canada) standard.)

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

• Do not use the WLAN adapter in the following locations. Using the WLAN adapter in such locations may cause communications becoming unstable or not possible.

  • Near wireless communication equipment that uses the same frequency band (2.4 GHz) as the WLAN adapter.
  • In places where there are magnetic fi elds from equipment such as microwave ovens, or static electricity or radio wave interference occurs.
    (Radio waves may not reach depending on the environment.)

• Personal Information (Security-related) Usage Precautions

• There is a possibility of interception if you use wireless LAN equipment due to the use of radio waves regardless of whether you use encryption or not.

• Wireless LAN uses radio waves to exchange information between the WLAN adapter and the access point. This means

it has the advantage of freely being able to make a LAN connection if within reach of radio waves. On the other hand,
if the radio waves are within a certain range, they will reach all locations beyond obstacles (e.g., walls). Therefore, it is possible your communications may be intercepted and read or illegally intruded upon.

• Do not connect to equipment and networks which you are not authorized to use when setting up your wireless connection.
• Initialize the settings of the WLAN adapter when disposing of it or transferring it to a third party.

Others

• Use the WLAN adapter as regular wireless LAN equipment.
  • Do not use the WLAN adapter in hospitals or in/near locations with medical equipment.
  • Do not use the WLAN adapter within an aircraft.
  • Do not use the WLAN adapter near electronic equipment that handles high-precision control or weak signals.

Examples of electronic equipment to be careful of:
Hearing aids, pacemakers, fi re alarms, automatic doors, and other automatic control equipment

• This is not a guarantee of wireless connection and performance with all wireless routers and in all residential environments. Radio waves may not reach or may be interrupted in the following situations.

  • Use in buildings made from concrete, rebars, or metal
    Installation near obstacles
    Interference with wireless communication equipment using the same frequency
    Places where there are magnetic fi elds from equipment such as microwave ovens, or static electricity or radio wave interference occurs

• Install and setup the WLAN adapter only after reading the operation manual of the access point.

Setting to use WLAN control

1. Step 1. Mobile app installation
2. Open “Google Play” or “App Store” depending on the type of your smartphone.
3. Search for “AIRSTAGE Mobile.”
4. install the mobile app following the instructions on your screen.
5. Step 2. User registration
6. Open the installed mobile app.
7. Register the user by following the instructions of the mobile app.
8. Step 3. Air conditioner registration (pairing of WLAN adapter)

NOTES

• Before starting this setting, wait for 60 seconds or more after the power supply is connected to the air conditioner (via breaker or plug).
  Check that the smartphone is linked to the access point you are connecting to the air conditioner. The setting does not work if it is not connected to the same access point.

• To control 2 or more air conditioners with the same smartphone, repeat the setup of the chosen mode.

  • Scan the QR Code on the WLAN adapter to use the automatic entry of the SSID and the PIN of the WLAN adapter.
    Refer to page 7 for the location of the QR Code.

  • Register the air conditioner by following the instructions of the mobile app.