ADVANTECH MIO-5152 Embedded Single Board Computers Instruction Manual

May 15, 2024
Advantech

ADVANTECH MIO-5152 Embedded Single Board Computers

ADVANTECH MIO-5152 Embedded Single Board Computers Instruction
Manual

Packing List

Before you begin installing your card, please make sure that the following items have been shipped:

  1. 1 x MIO-5152 SBC
  2. 1 x Startup manual p/n: 2046515200
  3. 1 x SATA cable p/n: 1700006291
  4. 1 x Audio cable p/n: 1700019584-01
  5. 6 x COM cable p/n: 1700030404-01
  6. 1 x USB cable p/n: 1700030406-01
  7. 1 x SATA power cable p/n: 1700031583-01
  8. 1 x Heatsink for x6000E p/n: 1970005053T001
  9. 1 x Heatsink for Celeron series p/n: 1970005053T011
  10. 1 x Device On package

If any of the above items are missing or damaged, contact your distributor or sales representative immediately.

Note 1: For more information regarding MIO-5152, refer to the Advantech website for further information.
Note 2: Acrobat Reader is required to view any PDF file. Acrobat Reader can be downloaded at: http://get.adobe.com/reader/ (Acrobat is a trademark of Adobe)

Specifications

General

  • CPU:

    • Intel® Celeron® J6412, 4 x cores, base frequency
      2.0GHz; Max frequency 2.6GHz

    • Intel® Celeron® N6210, 2 x cores, base frequency
      1.2GHz; Max frequency 2.6GHz

    • Intel® Atom® x6425E, 4 x cores, base frequency
      2.0GHz; Max frequency 3.0GHz

  • System Memory: Single channel, SODIMM DDR4-3200 MT/s, up to 32 GB

  •  CPU TDP:

    • Celeron® J6412: 10W
    • Celeron® N6210: 6.5W
    • Atom® x6425E: 12W
  • BIOS: AMI uEFI 256 Mbit

  • Watchdog Timer: 255 levels timer interval, programmable by software. Multi-level WDT (set by iManager)

  • Battery: Lithium 3 V/210 mAH

  • Audio: High-definition audio (HD), line-in, line-out, & mic-in

Expansion Interface

  • 1 x M.2 M-Key 2242
  • 1 x M.2 E-Key 2230 (option to B-Key 3042)

Display

  • Controller: Intel Gen 11 Graphics Engines (SoC integrated)
  • Maximum Resolution:
    • LCD: LVDS dual channel 18/24-bit up to 1920×1200
    • DisplayPort: DP1.4a, up to 4096 x 2160 x 36bpp@60Hz
    • HDMI: HDMI 1.4, up to 4096 x 2160 x 24bpp@60Hz
  • Multiple display
    • Triple simultaneous displays: LVDS + HDMI + DP

Ethernet Interface

  • Speed: 10/100/1000 BASE-T
  • Controller: 2 x Realtek RTL8111H

Mechanical and Environmentals Specs.

  • Dimensions: 146 x 102 mm (5.7 x 4 in)
  • Power Supply Type: ACPI support
  • Power Requirements: +12 V ± 10% (Default supports ATX 2x2pin 90D, DC Jack by T-P/N)
  • Operating Temperature: 0 ~ 60 °C (32 ~ 140 °F)

Jumpers and Connectors

The board has a number of jumpers that allow you to configure your system to suit your application. The table below lists the functions of each of the jumpers and connectors.

Jumpers

Label| Function
JCMOS1| CMOS clear switch
VDD1| Panel voltage selection
RI_VDD1| COM1 RI# pin RI#/5V/12V selection
Connectors

Label| Function
DCIN2| DC input connector
DCIN1| DC input connector (adapter)
LAN2| RJ45 connector (1 x port)
LAN1| RJ45 connector (1 x port)
USB56| Internal USB connector
DP1| DP connector
HDMI1| HDMI connector
USB2| USB 3.2 connector GEN2 (2 x ports)
USB1| USB 3.2 connector GEN2 (2 x ports)
COM1| COM port connector (RS232+RS422+RS485)
COM2| COM port connector (RS232+RS422+RS485)
COM3~6| COM port connector (RS232 only)
AUDIO1| Audio connector
DIMMA1| DDR4 SODIMM 260P/H9.2mm
LVDS1| LVDS connector
SATA1| HDD connector
SMB1| SMB bus connector
FAN1| FAN connector
SATAP1| HDD power connector
BL1| Inverter connector
PSON1| ATX/AT mode selection
GPIO1| GPIO connector
CN2| Power/LED/case open/Buzzer connector
M2_B1| M.2 Key B (PCIe_USB 2.0)
M2E1_1| M.2 Key E (PCIe_USB 2.0)
M2_M1| M.2 Key M (SATA)
BAT1| RTC battery connector
SIM1| SIM card connector

Jumper Settings

JCMOS1 CMOS Clear Switch
Setting Function
(1-2)* Keep COMS data (Default)
(2-3) Load CMOS date
VDD1 Panel Voltage Selection
Setting Function
(1-3)* Panel voltage settings: +V3.3 (Default)
(3-5) Panel voltage settings: +V5
(3-4) Panel voltage settings: +V12

Jumper Settings

RI_VDD1 COM1 RI# pin RI#/5V/12V Selection
Setting Function
(1-2) RI# Voltage settings: +V5
(5-6) RI# Voltage settings: +V12
(3-4)* RI# Voltage settings: RI# (Default)

Jumper Settings

Caution!
The computer is provided with a battery-powered real-time clock circuit. Batteries are at risk of exploding if incorrectly replaced. Replace only with same or equivalent type as recommended by the manufacturer. Discard used batteries according to manufacturer’s instructions.

PSON1 ATX/AT Mode Selection
Setting Function
(1-2) AT
(2-3)* ATX (Default)

Connector Locations

Connector Locations

Mechanical Drawings

Mechanical Drawings
Mechanical Drawings

Quick Installation Guide

There is a Heatsink in the white box, please remove the release paper from the thermal pads.

There are screws and stand-offs inside the box, follow the installation instructions demonstrated below to secure the heatsink:
Quick Installation Guide

CUSTOMER SUPPORT

MIO-5152 Intel® Atom® x6000E and Celeron® N and J series 3.5” SBC, DDR4, HDMI, DP, 2 x GbE, 4 x USB 3.2, M.2 E-key/B-Key, M.2 M-Key, 12V Power Input, iManager 3.0, & Edge AI Suite
Startup Manual

For more information about this and other Advantech
products, visit our website at
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and customer service, visit our
support website at
http://support.advantech.com
This manual is for the MIO-5152 Series.
Part No. 2046515200
Printed in China
Edition 1
Sep. 2021Logo

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Advantech User Manuals

Related Manuals