Advantech PCM-UR02 Android Mainboard User Guide
- June 3, 2024
- Advantech
Table of Contents
- Advantech PCM-UR02 Android Mainboard
- Specification
- Hardware Spec
- Specification
- Dimension drawing
- PCB Dimension
- Integration instructions for host product manufacturers according to KDB
- List of applicable FCC rules
- Specific operational use conditions
- Limited module procedures
- Trace antenna designs
- RF exposure considerations
- Antennas
- Label and compliance information
- Information on test modes and additional testing requirements
- Additional testing, Part 15 Subpart B disclaimer
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Advantech PCM-UR02 Android Mainboard
Specification
Product Overview
Overview
PCM-UR02 board is one Android mainboard based on RK3288 chip, with small
size, high performance, low power consumption, cost-effective and so on. It
supports Ethernet ,HDMI, WIFI, Bluetooth, Camera, supports most video and
image format, supports HDMI/VGA video output, LVDS display driver with dual 8
bits. It also could lighten different sizes of TFT LCD, simplify the system
design of the machine, with SD card an d SI M car d connector, more strong
stability ,suitable for POS cash register video advertising machine Self-
service terminals smart home and use d for various industry applications.
Description
- Full function: with USB/LVDS/MIPI/Ethernet/HDMI/WIFI/Bluetooth on board, simplifying the system design, with SD card connector.
- network support :built in PCI-E connector ;support all kinds of with PCI-E connector, transferring and updating on line better suited for remote maintenance of POS POS cash register 、 advertising machine, saving labor cost.
- Full extended connectors: eight USB2.0(6 sockets,2 standard USB 2.0),3 UART, GPIO/ADC satisfy all kinds of peripheral needs.
- High definition: Maximum support for 4K decoding and different kind of LCDs with LVDS singnal.
Sketch map of appearance and interface TOP:
Bottom:
Hardware Spec
Hardware Spec sheet
CPU| RK3288 Cortex A17 Quad-core @1.6GHz
Memory| 2G
FLASH| eMMC FLASH 16G
WIFI、Bluetooth| Built in Wifi/Bluetooth
|
Ethernet| X1,10M/100M/1000M
USB socket| 2 USB HOST + 6 USB socket
| 2 RS232 (ttyS1, ttyS3)+1 DB9-ttyS4
Extended memory| Support TF card
HDMI output| Support ,4K
LVDS output| Support Dual LVDS output
EDP output| Support ,1080P
Audio output| Support left/right channel output,Built Speaker、earphone socket、
Mic socket
RTC| Support
IR| Support
Time switch| Support
OS| Android8.1 above
OS updating| Support USB/TF/Network on line updating
Working temperature| 0~60°C
Weight(g)| 147.5
Specification
-
Video
Support avi、flv、wmv、rm、rmvb、mpeg 、ts、mp4 etc. -
Image
Support JPEG、PNG、GIF、BMP etc.
Dimension drawing
PCB Dimension
PCB:6 Layer
Size: 146mm*102mm(±0.5mm) , thickness1.6mm(±0.5mm)
Screw hole specification: Diameter3mm(±0.5mm) x 4
Note
During assembly and use, please pay attention to the following problems:
- Short circuit between bare board and peripherals.
- Pay attention to anti-static measures during assembly to avoid damaging the motherboard.
- When installing LVDS panel, pay attention to whether the voltage and current of the panel meet the requirements. Pay attention to the pin pin sequence of the screen socket.
- When installing LVDS screen, pay attention to whether the screen backlight voltage and current meet the requirements. If the power of the screen backlight is more than 20W, whether to use other power supply boards for power supply.
- When installing peripherals (USB, IO. Etc), pay attention to the IO level and current output of peripherals.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’ s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursua nt to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful inte
rference in a residential installation. This equipment generates uses and can
radiate radio frequency energy a nd, if not installed and used in accordance
with the instructions, may cause harmful interference to radio com
munications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turn
ing the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help important announcement
Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. Country Code selection feature to be disabled
for products marketed to the US/Canada.
This device is intended only for OEM integrators under the following conditions:
As long as the three conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
Important Note:
In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID cannot be used on
the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following”
Contains FCC ID: M82-PCMUR02″
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or
remove this RF module in the user’s manual of the end product which integrates
this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
Integration instructions for host product manufacturers according to KDB
996369 D03 OEM Manual v01
List of applicable FCC rules
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter
Specific operational use conditions
This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.
Limited module procedures
Not applicable
Trace antenna designs
Not applicable
RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Antennas
This radio transmitter FCC ID:M82-PCMUR02 has been approved by Federal
Communications Commission to operate with the
antenna types listed below, with the maximum permissible gain indicated.
Antenna types not included in this list that have a gain greater than the
maximum gain indicated for any type listed are strictly prohibited for use
with this device.
Antenna No.| Model No. of antenna:| Type of antenna:| Gain of the antenna
(Max.)| Frequency range:
---|---|---|---|---
Bluetooth&2.4G| /| PIFA Antenna| 1.26dBi for 2400~2500MHz;
5GWIFI| /| PIFA Antenna| 0.74dBi for 5150~5850MHz;
Label and compliance information
The final end product must be labeled in a visible area with the following” Contains FCC ID:M82-PCMUR02″.
Information on test modes and additional testing requirements
Host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host.
Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>