ClearOne UNITE 180 4K Panoramic Camera User Guide
- June 3, 2024
- ClearOne
Table of Contents
Quick-Start Guide
UNITE® 180 4K
Panoramic Camera
Important Safety Information
-
Before you set up the camera, read this manual carefully. Follow the setup instructions indicated in this manual.
-
Keep this manual for future use.
-
To prevent electric shock, do not remove screws or the camera housing. No self-serviceable parts are inside the housing.
-
Avoid direct sunlight or other heat sources. Keep unit away from moisture and humidity. Avoid inserting any sharp objects into the product. Avoid dropping the product to avoid damage.
-
Normal operating temperature is 32 to 104 °F (0 to 40 °C) 6.
-
Careful installation
• Install the camera on a smooth desktop or on the top of a computer monitor. -
Do not disassemble
• Damage caused by the user’s disassembly is not covered by warranty. -
Power
• Use only the included adaptor to power the camera. -
Electromagnetic fields at specific frequencies may affect the camera’s image.
WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE
THE LIGHTING FLASH AND ARROWHEAD WITHIN THE TRIANGE IS A WARNING SIGN ALERTING YOU OF DANGEROUS VOLTAGE INSIDE THE PRODUCT.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DU CHOC ELECTRIQUE – NE PAS
OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THE EXCLAMATION POINT WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF IMPORTANT INSTRUCTIONS ACCOMPANYING THE PRODUCT.
SEE MARKING ON BOTTOM/BACK OF PRODUCT
Use only in non-tropical locations.
Use only at altitudes of 2000 meters or less.
Packing List
Carefully inspect the shipment. If the shipment shows obvious signs of damage,
retain the box and packing material for inspection by the carrier. Contact the
carrier immediately.
ClearOne is not responsible for product damage incurred during shipment.
Installation
Wall Mounting
-
Use a ¼ in (6 mm) drill bit to drill two holes with a horizontal spacing of 1.1 in (28 mm) on the wall.
-
Push a rubber expansion plug into each hole.
-
Use a #2 Phillips screwdriver and the two self-tapping screws to attach the wall bracket to the wall.
-
Use the thumb screws to secure the camera to the bracket.
Monitor Mounting
-
On the underside of the camera body, open the damped rotating shaft bracket.
-
Place camera on top of a flat-panel monitor and adjust to your preferred position.
Connections
Use the included USB cable to connect the UNITE 180 to your computer.
Starting Up and Selecting a Viewing Mode
Immediately after you connect the UNITE 180 to a computer (if the computer is powered-on), Windows recognizes the UNITE 180 and the camera is available to use with your video collaboration software.
Six viewing modes are available with the UNITE 180, as follows:
- Compose
- Manual
- Autoframing
- Grid
- Presentation
- Speaker
To change the viewing mode, lightly tap the button on the top of the camera.
An explanation of the viewing modes is included in the UNITE 180 datasheet,
available in ClearOne’s Resource Library.
Details about how to use more powerful features of the UNITE 180 are included
in the UNITE 180 User Manual, available in ClearOne’s Resource Library.
Troubleshooting
| Problem | Resolution |
|---|---|
| The Image jitters | Check stability of the location: Remove vibrating objects |
| The image flashes | Eliminate unstable lighting. |
QSG-0131-002v1.1 August 2021
Contact Information
Headquarters
5225 Wiley Post Way
Suite 500
Salt Lake City, UT 84116
US: +1.801.975.7200
International: +1.801.975.7200
Aura Sales
US: +1.888.HEY.AURA
International: +1.801.975.7200
[email protected]
Aura Tech Support
US: +1.888.HEY.AURA
International: +1.801.975.7200
[email protected]
© 2021 ClearOne, Inc. All rights reserved. Information in this document is
subject to change without notice.
Document: QSG-0131-002v1.1, August 2021