HOTSPOT FHS2-UNV-36L Emergency LED Driver Instruction Manual

: June 10, 2024
: HOTSPOT

Table of Contents

HOTSPOT FHS2-UNV-36L Emergency LED Driver
INSTALLATION INSTRUCTIONS
General Specifications
Mechanical Data
- Wiring Diagrams 1
Battery Chart
Battery Dimensions
- Mounting Bracket Dimensions (Optional)
TEST SWITCH INDICATOR STATUS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HOTSPOT FHS2-UNV-36L Emergency LED Driver

HOTSPOT-FHS2-UNV-36L-Emergency-LED-Driver-PRODUCT

INSTALLATION INSTRUCTIONS

Emergency LED Driver
Output Wattage: 1.2-20W
Universal Voltage: 100-277VAC, 50/60Hz
Output Current range of 100mA – 700mA
Output voltage range of 12-55VDC
This Driver Will Operate The Following LED Modules: Any LED module designed to accept an input voltage range of 12-55VDC and can operate up to a current of 700mA.

General Specifications

Input Voltage: 100-277VAC, 50/60Hz
Input Current : 0.1A Max.
Input Power: 6W Max
Red Lead 3A,60V Max.
White/Black Lead 1A Max.
Standby Input Power : <0.8W
Driver Type: Constant Current
Output Current: 100mA -700mA Initial (Refer to accesory chart)
Output Voltage Range: 12-55VDC
Output Power: 20W Max
Number of Output Channels: 1 Channel
RFI/EMI: FCC Part 15 Class A
Output Type: LED Class 2
Battery Type: NiCd 9.6VDC or LiFePO4 9.6VDC
Battery Capacity Available: 900mAh, 1000mAh, 1200mAh, 1500mAh, 1800mAh, 3000mAh, 4000mAh, 6000mAh
Battery Recharge Time: 24-32 Hours (Refer To Battery chart)
Battery Discharge Time: 90 Minutes Min.
Test Switch Remote Mounting Distance: 20′ (6m) Max
Ambient Operating Temperature Range: NiCd: 0°C to 50°C (32°F to 122°F), LiFePO4: 10°C to 50°C (50°F to 122°F).
- FHSBATCC3-3: -20°C to 50°C (-4°F to 122°F)
- FHS2-UNV-36L: -20°C to 50°C (-4°F to 122°F)
Input Surge Protection: 2.5KV Ring Wave
Protections : Battery Over Discharge Protection: Output Short Circuit Protection
Service Life: 50,000 hours
Approvals / Class: RoHS , cURus 1310 , cURus 924 , CEC Title 20, Dry and Damp Locations, CE, EN61347-2-7:2012 RoHS , cURus 1310 , cURus 924 , CEC Title 20, Dry and Damp Locations, CE, EN61347-2-7:2012

Mechanical Data

HOTSPOT-FHS2-UNV-36L-Emergency-LED-Driver-
FIG-1

Fulham extends a limited warranty to the original purchaser or first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please refer to the Warranty Center at www.fulham.com. Specifications subject to change without notice.

Important and Safety Instructions
When using electrical equipment and this lighting device basic safety precaution should be followed at all times including but not limited to the following:

PLEASE READ CAREFULLY AND FOLLOW ALL INSTRUCTIONS FOR YOUR OWN SAFETY
IMPORTANT: Do not connect battery until fixture is installed.
IMPORTANT: An un-switched AC power source of 100VAC to 277VAC is required.
This device is designed for use in fixtures listed for dry and damp locations.
CAUTION: Make sure all electrical connections conform to the National Electrical Code and all applicable local regulations.
CAUTION: Do not let power supply cords touch hot surfaces.
CAUTION: Do not mount near gas or electric heaters.
CAUTION: Battery is rechargeable Ni-Cd or LiFePO4 type and must be recycled or disposed of properly. Do not use this emergency driver with accessory equipment
other than recommended by manufacturer; failure to follow this may cause an unsafe condition. Servicing should only be performed by qualified service personnel.
Do not use this emergency driver for other than intended use.
Not suitable for high-risk task area lighting.
Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel.
IMPORTANT: The output EM power will not exceed the max power rating of the battery.
IMPORTANT: Indicator (LED light) illuminated indicates battery in charge mode when AC power is applied. It is recommended and required by applicable code to test emergency ballast to ensure proper function of the system; push the test switch for thirty (30) seconds every thirty (30) days to ensure the emergency driver is functioning by illuminating the light source. Conduct a ninety (90) minutes discharge test one (1) time per year; LED light source should be illuminated for a minimum of ninety (90) minutes .
ASSEMBLY and FIELD INSTALLATION WIRING: WARNING: AC power must be off before proceeding with assembly or installation of emergency driver.
TESTING SYSTEM: The emergency battery requires a charge minimum of one (1) hour before testing the circuit. A full charge requires twenty four (24) or thirty two (32) hours, depending upon battery pack. Please refer to battery chart for charging time.
IMPORTANT: In order to maintain proper operation and warranty coverage, the battery must be recharged once per year prior to installation.

Wiring Diagrams 1

HOTSPOT-FHS2-UNV-36L-Emergency-LED-Driver-
FIG-2

Wiring Diagram (TYP)

WIRING DIAGRAM (EMERGENCY ONLY)

Battery Chart

**Fulham Model No.| ****Chemistry| ****Compliant| Pack Capacity| Max Load for 90 min.| Battery Voltage| Battery Count| Recharge Time| Dimensions (L x W x H)| 12″ Harness (Optional)| Mounting Accessory (Included / Optional)
---|---|---|---|---|---|---|---|---|---|---
FHSBATT8-AA.9| NiCd| | 900mAh| 4W| **

**** 9.6V

| 8 Cells| 24Hrs| 5.23″ x 2.5″ x 0.7″| FHS-EXTM| Bracket Included
FHSBATL3-1| LiFePO4| RoHS| 1000mAh| 4W| 3 Cells| 24Hrs| 3.48″ x 2.35″ x 0.99″
FHSBATL6-.6| LiFePO4| RoHS| 1200mAh| 6W| 6 Cells| 24Hrs| 5.23″ x 1.87″ x 0.85″
FHSBATL3-1.5| LiFePO4| RoHS| 1500mAh| 8W| 3 Cells| 24Hrs| 3.48 “x 2.76″ x 0.99”
FHSBATL3-1.5S| LiFePO4| RoHS| 1500mAh| 8W| 3 Cells| 24Hrs| 8.87″ x 1.11″ x 0.955″
FHSBATL9-.6| LiFePO4| RoHS| 1800mAh| 10W| 9 Cells| 24Hrs| 7.52″ x 1.87″ x 0.85″
FHSBATCC3-3| LiFePO4| RoHS| 3000mAh| 14W/10W*| 3 Cells| 24Hrs| 6″ x 3.6″ x 1.55″
FHSBATT8-C3| NiCd| | 3000mAh| 16W| 8 Cells| 24Hrs| 4.15″ x 3.29″ x 2.11″
FHSBATT8-C3L| NiCd| | 3000mAh| 16W| 8 Cells| 24Hrs| 7.89″ x 2.17″ x 1.04″| FHSBATSC8-C3L
FHSBATL3-3| LiFePO4| RoHS| 3000mAh| 16W| 3 Cells| 24Hrs| 4.39″ x 2.82″ x 1.3″|

Bracket Included

FHSBATL6-1.5| LiFePO4| RoHS| 3000mAh| 16W| 6 Cells| 24Hrs| 5.7″ x 2.76″ x 0.99″
FHSBATL6-1.5L*| LiFePO4| RoHS| 3000mAh| 16W| 6 Cells| 24Hrs| 7.89″ x 1.56″ x 0.92″| FHSBATSC6-1.5L
FHSBATL6-1.5S| LiFePO4| RoHS| 3000mAh| 16W| 6 Cells| 24Hrs| 16.67″ x 1.11″ x 0.955″| ****

Bracket Included

FHSABATT8-D4| NiCd| | 4000mAh| 20W| 8 Cells| 24Hrs| 4.89″ x 3.84″ x 2.72″
FHSBATL6-3| LiFePO4| RoHS| 6000mAh| 20W/16W*| 6 Cells| 32Hrs| 7.52″ x 2.82″ x 1.3″
FHSBATL6-3L| LiFePO4| RoHS| 6000mAh| 20W/16W**| 6 Cells| 32Hrs| 7.94″ x 2.17″ x 1.21″| FHSBATSC6-3L

CAUTION: Replace battery only with corresponding part number.
Note: These batteries do not include mounting means, separate mounting brackets are available.
Note: This battery rating applies for Canada use only.

Accessory Harness (Wire length 24″)

Battery Dimensions

HOTSPOT-FHS2-UNV-36L-Emergency-LED-Driver-
FIG-5

Mounting Bracket Dimensions (Optional)

Battery Dimensions

TEST SWITCH INDICATOR STATUS

Indicators Type	LED Indicators Status	EM Driver Status/Mode
Bi-Color Indicator	● Solid Green	System OK/AC OK (Self-diagnostic Enabled or

Disabled).
Single Color Indicator| ● Solid RED ON
Bi-Color Indicator| ● Flashing Green, 0.1s on/3s off| System OK / EM Mode
Single Color Indicator| ● Flashing RED, 0.1s on/3s off
Bi-Color Indicator| ● Slow Flashing Red, 4s on/1s off| Battery not detected, check battery switch or connection.
Single Color Indicator| ● Slow Flashing Red, 4s on/1s off
Bi-Color Indicator| ● Flashing Red, 1s on/1s off| Replace battery.
Single Color Indicator| ● Flashing Red, 1s on/1s off
Bi-Color Indicator| ● Flashing Green, 2s on/2s off| Self-Diagnostic test underway.
Single Color Indicator| ● Flashing Red, 2s on/2s off
Bi-Color Indicator| ● Fast Flashing Red, 0.1s on/0.1s off| Abnormal driver performance, replace driver.
Single Color Indicator| ● Fast Flashing Red, 0.1s on/0.1s off
Bi-Color Indicator| ● Very Slow Flashing Red, 1s on/7s off| Over temperature.
Single Color Indicator| ● Very Slow Flashing Red, 1s on/7s off
Bi-Color Indicator| ● Very Slow Flashing Red, 4s on/4s off| LED output load is Short/Over Current/Over Voltage/Open Circuit in EM Mode.
Single Color Indicator| ● Very Slow Flashing Red, 4s on/4s off

TEST SWITCH OPERATIONS:

EM Test: Press and hold test button (>1s)to enter EM mode for testing in normal AC powered .
Manual Self-Diagnostic: After charging twelve (12) hours or battery fully charged, quickly press the test button three times within two seconds to force the controller to enter a Self-Diagnostic cycle. To quit the self-diagnostic cycle after engaged press and hold the test button for ten seconds.
Enable/Disable Auto Self-Diagnostic: Press and hold the test button for one second, then release and quickly press the test button two times, then release and press and hold the test button for two seconds. When properly executed the indicator on the test button will display the appropriate color for the Enable/Disable status. A flashing of
2.5s ON/0.5s OFF means “Enabled”, while a flashing of 0.5s ON/2.5s off means “Disabled”. Once Enable/Disable is set the status color on the test button will remain the same throughout normal operation (refer to Indicator Status Table).
Enable/Disable Self-Diagnostic Status: Fast click 2 times within 2s to query the Self-Diagnostic Enabled/Disabled status. The indicator would blink for current status for 3 cycles. 2.5s ON/0.5s OFF stands for Enabled. 0.5s ON/2.5s OFF stands for Disabled.
Exit Output Short Circuit/No Load/Over Voltage Protection: When the test button flashes red for 4s on/4s off, press and hold the test switch for 10 seconds.
Turn off EM output: Press and hold the test switch for 10 seconds during EM output condition to turn off EM output. This is useful for production environment to turn off the EM output once a luminaire has completed functionality testing. This applies to products with Serial Number starting with Date code: S12016 or higher.

Programming:

Unless otherwise programmed the output will self-program to the rated output of the harness. This driver can be programmed using Fulham SmartSet TPSB-100 or
TPSM-100E. Programming features include the following:
Enable/Disable Self-Diagnostic
Output EM Current : 0mA,100-700mA
When programmed to 0mA; output current defaults to rating of output harness(Refer to accessory harness chart).
Fulham extends a limited warranty to the original purchaser or first user for a period of 5 years from the date of manufacture when properly installed and operated under normal conditions of use. For complete terms and conditions, please refer to the Warranty Center at www.fulham.com. Specifications subject to change without notice.
Fulham Head Quarters:
Fulham Co., Inc
12705 South Van Ness Ave.
Manufacturer:
North China
Fulham Electronic Co. Ltd.
No. 9 Xingchang Road, Nanshao Zhen Changping Science Park, Beijing, P.R. China