Fender LT50 Mustang Guitar Speaker User Manual
- June 17, 2024
- fender
Table of Contents
Fender LT50 Mustang Guitar Speaker User Manual
CONTROL PANEL
The Mustang LT50 top control panel consists of an INSTRUMENT INPUT, six CONTROL KNOBS, a DISPLAY WINDOW, an ENCODER wheel, four UTILITY pushbuttons, a FOOTSWITCH INPUT, an AUXILIARY INPUT (1/8”), a HEADPHONE OUTPUT (1/8”), a TAP LIGHT and a USB PORT.
- INPUT: Plug the instrument in here.
- AUXILIARY INPUT, HEADPHONE OUTPUT: 1/8” auxiliary input for connecting external audio devices, and 1/8” output for headphone use (page 22). Headphone output mutes speaker.
- GAIN: Effects gain setting in active preset.
- VOLUME: Affects individual volume of active preset.
- TREBLE: Affects treble tone setting in active preset.
- MIDDLE: Affects midrange tone setting in active preset.
- BASS: Affects bass tone setting in active preset.
- MASTER VOLUME: Controls the actual overall volume.
- DISPLAY WINDOW: Shows preset in use, preset contents and parameters, and other functions (i.e., tuner and other menu functions).
- ENCODER: Rotary control with press-switch function. For viewing, selecting and adjusting the Mustang LT50 presets, controls and other functions.
- UTILITY BUTTONS
- BACK: Returns the user to the previous screen or original preset screen.
- SAVE: For saving preset modifications, renaming presets and saving presets to a new location.
- MENU: For accessing tuner, footswitch and other functions (page 15).
- TAP: For setting delay times (page 12) and accessing the built-in tuner (page 16).
- TAP LIGHT: Flashes in time with delay effects.
- POWER: Turns the amplifier on and off.
- USB PORT: Amp connection point for USB audio recording (page 23).
- IEC POWER INLET (REAR PANEL; NOT SHOWN): Using the included power cord, connect to a grounded outlet by the input power voltage and frequency specified at the power inlet.
- FOOTSWITCH (REAR PANEL; NOT SHOWN): Connect the optional four-button footswitch here (page 17).
- MONO LINE OUT (REAR PANEL; NOT SHOWN): Mono line output for connection to external sound and recording equipment (page 23).
PRESET BASICS
Mustang LT50 features 30 sequentially numbered factory presets. It also
features 30 empty preset “slots” for presets created by the user and presets
downloaded using the Fender TONE™ app (page 23). Each preset consists of an
amplifier and one or more effects (or, in some cases, no effects). Note that
when turning the amplifier on, the default active preset is always preset 01.
All 60 preset slots can be customized by the user, and the original 30 factory
presets can always be restored if needed by using the “REPLACE” function in
the SAVE menu (page 7). To scroll through presets, turn the ENCODER; whichever
preset is displayed becomes active:
Mustang LT50’s 30 factory presets are
- FENDER CLEAN 11 METAL LEAD 21 TOUCH WAH
- SILKY SOLO 12 VINTAGE TREMOLO 22 SUPER ROCK
- CHICAGO BLUES 13 SUPER DRY CLEAN 23 NICE FLANGER
- CLASSIC ROCK 14 THRASH OVERKILL 24 VIBRA DOOM
- DREAMY 15 CLEAN DELAY 25 SURF MUSIC
- COUNTRY PICKING 16 OCTOBOT ONE NOTE 26 BLUES LEAD
- SKATE PUNK 17 LITTLE CHAMP 27 ROCK A BILLY
- SOLO MIDBOOST 18 PHASER SWIRL 28 GARAGE FUZZ
- JAZZ AMP 19 60S FUZZ 29 SPACE TRAVEL
- BRIT 64 RHYTHM 20 MYTHIC CRUNCH 30 ACOUSTIC SIM
EDITING AND SAVING PRESETS
Presets can be easily edited and, if desired, renamed and saved in place or
saved in a different location. The controls of each amplifier type can be
adjusted, or an amp model can be replaced with a different one. Similarly,
various effects controls can be adjusted, or effects can be removed from or
added to a preset. When a preset is active, the box containing its number is
blue, indicating that no edits have been made. Once an edit is made, the box
containing the preset number turns red and the preset title screen will read
“UNSAVED”. When edits are saved, the preset number box returns to blue and the
“UNSAVED” title clears.
ACCESSING PRESET CONTENTS
To access the contents of a preset, press the ENCODER. From the top down, the
DISPLAY WINDOW will then show the number and name of the preset, the amplifier
type in use, and four boxes that organize the effects used for that preset (if
any). These effects category boxes are labelled STOMP (stompbox), MOD
(modulation), DELAY and REV (reverb). When first accessing preset contents,
the preset name and amplifier type are highlighted in blue: Select the amp
model or one of the effects category boxes by turning and pressing the
ENCODER. The active selection is then highlighted in blue:
EDITING AND SAVING AMPLIFIER CONTROL SETTINGS
To edit and save individual control settings of a preset’s amplifier model,
first select the amp model by pressing the ENCODER on it. The DISPLAY WINDOW
will then show a list of controls for the amp model in use: There are two ways
to adjust an amp control knob setting. A control parameter that corresponds to
an actual physical knob on the control panel can be adjusted simply by turning
the physical control knob until the desired value is reached in the DISPLAY
WINDOW. In the example below, the amp model’s TREBLE setting is adjusted by
turning the physical TREBLE control knob on the control panel:
Alternately, select a control parameter by turning and pressing the ENCODER; its surrounding box will turn from blue to red: The control can then be adjusted by turning the ENCODER or by turning a corresponding physical control knob on the control panel: At this point, press the ENCODER or the BACK utility button (green arrow) to accept the adjusted control values. Pressing BACK returns the user to the preset contents screen; pressing the ENCODER lets the user continue making control setting changes, and the box surrounding the control setting will return to blue. When control setting edits are complete, press the SAVE utility button to save the changes to the preset.
IMPORTANT: If edited amp control settings are not saved, the preset will revert to its original amp control settings when returning to the preset after leaving it, or when turning the amplifier off and back on again. To save edited amp control settings, press the SAVE utility button and use the ENCODER to scroll to one of three options—SAVE, SAVE AS or REPLACE. Each is detailed below.
SAVE: Keeps an edited preset in the same location with the same name. To
do this, press the SAVE utility button and use the ENCODER to scroll to
“SAVE”. Press the SAVE utility button again or press the ENCODER. A brief
“PRESET SAVED!” screen will then flash before returning to the original preset
screen:
SAVE AS: Enables saving a preset in a different position, with or without a different name.
To do this, press the SAVE utility button and use the ENCODER to scroll to “SAVE AS”. Press the ENCODER to access a “CHOOSE SLOT” list of locations where the preset can be moved. Select a new location by turning and pressing the ENCODER: Whether renaming the preset or not when using “SAVE AS”, a name must be entered by pressing the ENCODER to activate a cursor, then spelling out the name by turning and pressing the ENCODER to scroll through and select characters. All characters can be cleared by using the ENCODER to scroll to and select “CLEAR ALL”. When name entry is completed for the new location, save it by pressing the SAVE utility button or by using the ENCODER to scroll to and select “SAVE”. A brief “PRESET SAVED!” screen will then flash before returning to the original preset screen:
REPLACE: Any existing preset can be replaced with another by pressing the SAVE utility button, using the ENCODER to scroll to and select “REPLACE” and choose among the 30 original factories presets (page 3). After selecting “REPLACE”, use the ENCODER to scroll to any of the 30 presets; each one is automatically “previewed” so the user can hear it before the preset is loaded. Press the ENCODER to select the preset, confirm it by using the ENCODER to scroll to and select “NO CANCEL” or “YES REPLACE” (not shown) and save it in the chosen slot:
CHANGING THE AMPLIFIER MODEL IN A PRESET
The amplifier model in a preset can be replaced with another one (see list of Mustang LT50 amplifier models on page 8).
To do this, access the contents of a preset by pressing the ENCODER on it; the amp model will automatically be highlighted. Press the ENCODER again to see a list of controls for the amp model in use; the name of the amp model appears at the top of this list. Press the ENCODER once more to activate the amplifier replacement function; the box surrounding the amp name will turn from blue to red, and white arrows will bracket the amp name.
Turn the ENCODER to scroll to a new amp model.
Press the ENCODER to accept the amp model change, after which the box surrounding the amp name will return to blue; or press the BACK utility button to accept the amp model change and return to the preset contents screen:
IMPORTANT: If an amplifier replacement is not saved, the preset will revert to its original amp type when returning to the preset after leaving it, or when turning the amplifier off and back on again. To save a preset amp replacement, follow the SAVE, SAVE AS or REPLACE instructions on page 6 and at the top of this page.
MUSTANG LT50 AMPLIFIER MODELS
This table lists the amp models in the Mustang LT50. The amp label used in
each preset appears in the lefthand column, followed by the amp type and a
brief description in the righthand column.
PRESET AMP LABEL AMP TYPE AND DESCRIPTION
SUPER CLEAN| Direct-to-mixing-desk studio-preamp purity with clean,
uncolored tonal response
---|---
CHAMP| Based on the ’57 Champ®—the small but mighty late-’50s Fender
recording great
DELUXE DIRT| Based on a 1957 Deluxe™—a medium-power late-’50s Fender
tweed classic known for thick, compressed overdrive
50S TWIN| Based on a 1957 Twin—an original-era 2×12” Fender tweed
classic prized for clean-to-dirty versatility
BASSMAN| Based on the venerable ’59 Bassman®—one of Fender’s greatest
tweed amps, which began life as a bass amp before being adopted by countless
guitarists
PRINCETON| Based on a 1965 Princeton®—a mid-’60s Fender studio favorite
with the snappy tone of a single 10” speaker
DELUXE CLN| Based on the highly popular 1965 Fender Deluxe Reverb®—an
amp with great tone whether clean or dirty, and cranked in countless clubs
TWIN CLEAN| Based on the 1965 Fender Twin Reverb®—an indispensable
mid-’60s stage-and- studio favorite prized for producing the Fender clean tone
EXCELSIOR| An elegantly eccentric modern-day Fender model with the
distinctive thump of a 15” speaker
SMALLTONE| Inspired by the garage-classic 1960s Sears Silvertone beloved
of retro/alternative players
70S UK CLN| Inspired by the original 100-watt Hiwatt DR103, which is the
classic cleaner-tone British stack
60S UK CLN| Inspired by the Vox AC30, which powered the British Invasion
and produced remarkable clean and dirty tone
70S ROCK| Inspired by a late-’60s/early-’70s Marshall Super Lead, the
amp that powered the dawn of hard rock
80S ROCK| Inspired by the Marshall JCM800, which produced quintessential
’80s metal tone
DOOM METAL| Inspired by the “sludgy” majesty of the Orange OR120
BURN| Based on the “burn” channel of the modern Fender Super-Sonic amp,
which has two cascading preamp gain stages for pronounced sustain
90S ROCK| Based on the Mesa Dual Rectifer, which featured distinctive
distortion that shaped the “nu-metal” sound
ALT METAL| Based on the distinctive nu-metal-defining distortion of
the Mesa Dual Rectifier, gat- ed with a very fast attenuation curve especially
ideal for high-gain metal
METAL 2000| Modern high-gain scorch based on the EVH® 5150III
SUPER HEAVY| Modern high-gain scorch based on the EVH® 5150III, gated
with a very fast attenua- tion curve especially ideal for high-gain metal
EDITING AND SAVING EFFECTS CONTROL SETTINGS
To edit and save individual control settings of a preset’s various effects (if
any), first select the effect category box containing the effect to be edited
by turning and pressing the ENCODER. There are four effects category boxes
that can each contain one effect: STOMP (stompbox), MOD (modulation), DELAY
and REV (reverb):
The DISPLAY WINDOW will then show a list of controls for the effect model
in use in that category; use the ENCODER to scroll to a particular effect
control. Press the ENCODER to select the effect control; it’s surrounding
the box will turn from blue to red. Turn the ENCODER to set a new value for
the selected control value:
At this point, press the ENCODER to accept the adjusted effect control value and exit edit mode; the surrounding box will then return to blue. Alternately, press the BACK utility button (green arrow) to accept the effect control value change and return to the preset contents screen:
IMPORTANT : If an edited effect control setting is not saved, the preset will revert to its original effect control settings when returning to the preset after leaving it, or when turning the amplifier off and back on again. To save edited effect control settings, follow the SAVE, SAVE AS or REPLACE instructions on pages 6 and 7.
REPLACING, ADDING AND DELETING EFFECTS
As noted, each of the four effect category boxes can contain one effect. If an
effect is present, it can be replaced with another effect in that category, or
it can be deleted. If no effect is present, one can be added (see list of
Mustang LT50 affects models on pages 13-14). The signal path is
Instrument—Stompbox—Modulation— Amplifier—Delay—Reverb—Speaker, as illustrated
at left below. Note that effects category boxes that already contain an effect
have a solid outline, whereas effects category boxes that do not contain an
effect have a dotted outline, as seen in the image at right below:
To replace an effect, access the contents of a preset by pressing the ENCODER on it, then use the ENCODER to scroll to one of the four effect category boxes. Press the ENCODER again to see the effect contained in the effect category box; the name of the effect model is highlighted at the top of the DISPLAY WINDOW:
Press the ENCODER once more to activate the effect replacement function; the box surrounding the effect name will turn from blue to red, and white arrows will bracket the effect name. Turn the ENCODER clockwise to scroll through other effects models in that category. Press the ENCODER to accept a replacement effect and exit edit mode; the surrounding box will return to blue. Alternately, press the BACK utility button (green arrow) to accept the replacement effect and return to the preset contents screen:
To delete an effect, the steps are very similar to those on page 10. As before, access the contents of a preset by pressing the ENCODER on it, then use the ENCODER to scroll to an occupied effect category box. Press the ENCODER again to see the effect contained in the effect category box; the name of the effect model is highlighted at the top of the DISPLAY WINDOW:
Press the ENCODER once more to activate the effect replacement function; the box surrounding the effect name will turn from blue to red, and white arrows will bracket the effect name. Turn the ENCODER counterclockwise until the red- highlighted effect label at the top of the DISPLAY WINDOW reads “NONE”. Press the ENCODER on “NONE” (or press the BACK utility button), after which the user is returned to the preset screen with the previously occupied effect category box now empty:
To add an effect to an empty effect category box, first access the contents of a preset by pressing the ENCODER on it, then use the ENCODER to scroll to the empty effect category box. Press the ENCODER again to access the empty effect category box; the red-highlighted label “NONE” will appear at the top of the DISPLAY WINDOW:
Turn the ENCODER clockwise to scroll through effects models in that category. Press the ENCODER on the desired effect, after which the box surrounding the effect name will return to blue and the effect is added— although not yet saved—to that effect category box. Alternately, press the BACK utility button (green arrow) to return to the preset contents screen (see illustrations on next page):
IMPORTANT: If an effect is not saved once it has been replaced, deleted or added, the preset will revert to its original effect model(s) when returning to the preset after leaving it, or when turning the amplifier off and back on again. To save a changed, deleted or added effect model, follow the SAVE, SAVE AS or REPLACE instructions on pages 6 and 7.
SETTING DELAY TIMES WITH THE TAP BUTTON
There are three ways to set delay times for effects in Mustang LT50’s “DELAY”
effects category box. The first way is to use the “Editing and Saving Effects
Control Settings” instructions found on page 9, using the ENCODER to scroll
to, select and adjust individual effect settings, including delay time. The
second way is to use the Mustang LT50’s TAP utility button (yellow arrow). If
a preset includes a delay effect, the TAP LIGHT (green arrow) flashes in time
with that effect’s default delay time. This time setting can be modified by
tapping the TAP utility button two or more times at the desired tempo,
regardless of what screen is shown in the DISPLAY WINDOW: The third way to set
delay times is to use the four-button footswitch; see page 19 for instructions
on how to do this.
IMPORTANT: If an edited delay time is not saved, the effect will revert
to its original delay time when returning to the preset after leaving it, or
when turning the amplifier off and back on again. To save an edited delay
time, follow the SAVE, SAVE AS or REPLACE instructions on pages 6 and 7.
MUSTANG LT50 EFFECT MODELS
This table lists the effect models in Mustang LT50, organized into the four
categories that appear in each preset—STOMP (stompbox), MOD (modulation),
DELAY and REV (reverb). The effects labels used in each preset
appear in the lefthand column, followed by the effects types and a brief
description in the righthand column.
STOMPBOX EFFECTS
OVERDRIVE| Versatile Fender overdrive specially designed for Mustang
LT50
---|---
BLUES DRIVE| Overdrive effect inspired by the original late-’70s
Ibanez TS808 Tube Screamer
MYTH DRIVE| Overdrive effect inspired by the ’90s-era Klon Centaur
ROCK DIRT| Distortion effect inspired by the Pro Co RAT
FUZZ| Versatile Fender fuzz with variable low-end response specially
designed for Mustang LT50
BIG FUZZ| Distortion effect inspired by the Electro-Harmonix Big
Muff
OCTOBOT| Synth-like combination of octave-down effect plus octave-up
fuzz
COMPRESSOR| Compressor effect inspired by the classic MXR Dyna Comp
SUSTAIN| Inspired by the MXR M-163 Sustain, a rare 1980s compressor
pedal with an especially strong compression effect and short attack time
METAL GATE| Noise gate with a very fast attenuation curve especially
ideal for high-gain metal
5-BAND EQ| Five-band graphic equalizer
MODULATION EFFECTS
CHORUS| Distinctive chorus effect that uses a triangle wave for
modulation
---|---
FLANGER| Distinctive flanging effect that uses a triangle wave for
modulation
VIBRATONE| Classic late-’60s/early-’70s Fender effect with a rotating
speaker baffle
TREMOLO| Smoothly pulsating tube bias tremolo, as heard in amps such as
the Fender Princeton Reverb
PHASER| Long-indispensable jetliner “whoosh” heard on countless
recordings
STEP FILTER| The rhythmically choppy effect that dices notes into
distinctly alternating “steps”
TOUCH WAH| Wah effect is controlled by picking dynamics rather than an
expression pedal
All non-FMIC product names and trademarks appearing in this manual are the property of their respective owners and are used solely to identify the products whose tones and sounds were studied during sound model development for this product. The use of these products and trademarks does not imply any affiliation, connection, sponsorship, or approval between FMIC and with or by any third party
DELAY EFFECTS
Note that the control panel TAP utility button and TAP LIGHT work in
connection with effects in this category only.
DELAY | Clean, simple and pristine signal repetition |
---|---|
REVERSE | Reverses the delayed signal for the classic “backwards guitar” |
effect
ECHO| Tape delay effect based on the analog classic Maestro Echoplex,
which had tape im- perfections that created distinctive “wow” and “flutter”
REVERB EFFECTS
All non-FMIC product names and trademarks appearing in this manual are the
property of their respective owners and are used solely to identify the
products whose tones and sounds were studied during sound model development
for this product. The use of these products and trademarks does not imply any
affiliation, connection, sponsorship, or approval between FMIC and with or by
any third party.
LARGE HALL| Strong, bright reverb simulating the size of, for
example, a major performance hall and other large, cavernous spaces
---|---
SMALL ROOM| Warmer, less echo-y reverb typical of smaller spaces and
classic echo chambers
SPRING 65| Fender reverb effect built into classic mid-’60s Fender
amps
PLATE| The reverb type heard on countless recordings, based on the
classic (and pool table-sized) EMT 140
ARENA| Simulates the long-trailing reverberation typical of large
stadiums and arenas
MENU FUNCTIONS
Mustang LT50 features five convenient MENU functions—TUNER, FOOTSWITCH,
LEVELS, RESTORE and
ABOUT— all easily accessed by pressing the MENU utility button. The first
function (TUNER) is automatically highlighted; use the ENCODER to scroll to
and select any MENU function:
TUNER: Enables the use of Mustang LT50’s built-in chromatic tuner (page
16).
FOOTSWITCH: For configuring the quick-access preset, effects on/off and
tuner functions of Mustang LT50’s optional four-button footswitch (page 17).
LEVELS: Level control with a signal-strength meter for use when recording
using the USB audio port on the control panel, or when using the rear-panel
mono line output to send a signal to external sound and recording equipment
(page 21).
RESTORE: Enables restoration of factory presets and amplifier settings
(page 21).
ABOUT: Displays the amp’s current firmware version (page 22).
MENU FUNCTION: TUNER
There are three ways to access the Mustang LT50’s built-in chromatic tuner. The first way is to press and hold the TAP the utility button on the control panel until the tuner screen appears in the DISPLAY WINDOW:
The second way is to press the MENU utility button on the control panel; the list of MENU functions will appear in the DISPLAY WINDOW with the TUNER function automatically highlighted atop the list.
ENCODER on TUNER to access the tuner screen
To use the TUNER, sound a note; the letter name of the pitch will appear in
the box at the bottom and the shorter vertical bars on either side of the
longer vertical centre bar will illuminate red to indicate varying degrees of
sharpness (to the right) or flatness (to the left). When a pitch is precisely
in tune, the longer vertical centre bar and the two shorter vertical bars on
either side of it will illuminate green: Note that speaker output is muted
when tuning and that the volume control on the instrument being tuned must be
turned up sufficiently to register a TUNER reading. The third way to access
the tuner is by using the footswitch. To use the footswitch for hands-free
chromatic tuning, see the instructions on page 20.
MENU FUNCTION: FOOTSWITCH
Connect the optional four-button MGT-4 footswitch by plugging it into the
“FOOTSWITCH” jack on the rear panel; note that Mustang LT50 comes with a
magnetic footswitch overlay that provides correct footswitch labelling for the
MGT-4 and other compatible four-button Fender footswitches*. The footswitch
provides convenient quick-access preset selection, effects on/off switching
and delays tap tempo control and a hands-free tuner function. When the
footswitch is connected and the amplifier is on, the footswitch is
automatically synched with the active preset, and the red “BANK 1” LED at the
far left will illuminate. For example, if preset 9 (“Jazz Amp”) is active and
the footswitch is connected to the amp, the footswitch will synch up with that
preset, as indicated by “P09” in the footswitch’s display window:
FOOTSWITCH: QUICK ACCESS PRESETS
The four-button footswitch can be configured for hands-free switching among up to eight “quick-access” presets, arranged in two “banks” of four presets each. To do this press the MENU utility button and use the ENCODER to scroll to and select “FOOTSWITCH.” Both quick-access preset banks will appear in the DISPLAY WINDOW below the header “QUICK ACCESS”; the upper bank (“BANK 1”) is automatically highlighted in blue.
Press the ENCODER on it, and the four preset slots in the first bank appear with their default settings, labelled “A”, “B”, “C” and “D” to correspond to the “A”, “B”, “C” and “D” buttons on the footswitch. The first preset slot (“A”) will be highlighted in blue: Older Fender MS-4 and ULT-4 four-button footswitches are also compatible with Mustang LT50. The magnetic footswitch overlay that comes with Mustang LT50 fits both footswitches.
To assign a different preset to slot “A”, for example, press the ENCODER on it. A “CHOOSE SLOT” screen then appears with a numbered list of 30 presets, the first of which is highlighted in red. Use the ENCODER to scroll to and select a new preset for slot “A” (preset 18 in the example here):
The new preset now occupies preset slot “A”. Use the same steps to replace the presets in slots “B”, “C” and “D” in BANK 1 if so desired. To set four more quick-access presets, use the ENCODER to scroll to and select the second bank (“BANK 2”), then follow the same steps:
Once configured, all eight quick-access presets are easily accessible using the footswitch. When the amp is on and the footswitch is connected, BANK 1 is automatically active, and the four presets contained in it are assigned to footswitch buttons “A”, “B”, “C” and “D”. Simply step on the button corresponding to the desired preset. In the example here, preset 18 has been assigned to slot “B” in BANK 1 (as indicated by the illuminated red BANK 1 LED at far left, the illuminated red LED above switch “B” and in the footswitch display window); step on the footswitch button “B” to activate it (yellow arrow):
To access the presets in BANK 2, step on buttons “A” and “B” simultaneously.
The green “BANK 2” LED at the far left will illuminate, indicating that the
four presets in BANK 2 have been assigned to footswitch buttons “A”, “B”, “C”
and “D”. As before, step on the button corresponding to the desired preset. In
the example here, preset 5 has been assigned to slot “A” in BANK 2 (as
indicated by the illuminated green BANK 2 LED at far left, the illuminated red
LED above switch “A” and in the footswitch display window), so step on the
footswitch button “A” to activate it:
FOOTSWITCH: EFFECTS ON/OFF
Effects in a preset (if any) can be turned on and off using the footswitch. To
do this, step on buttons “A” and “B” simultaneously until the amber “EFFECTS”
LED illuminates at far left (see illustration below). Footswitch buttons “A”,
“B”, “C” and “D” are also respectively labelled as “STOMP” (A), “MOD” (B),
“DELAY” (C) and “REVERB” (D). Since one effect only from each of these four
categories can appear in a preset, any effects used in a preset are
automatically assigned to the four footswitch buttons.
In the example here, active preset 9 contains one stompbox effect and one reverb effect. Consequently, with the footswitch in “EFFECTS” mode, the stompbox effect is automatically assigned to footswitch button “A” and the reverb effect is automatically assigned to button “D” (the preset has no modulation or delay effects, so footswitch buttons “B” and “C” are inactive). Merely step on these buttons to turn these effects on and off:
FOOTSWITCH: TAP TEMPO FOR DELAY EFFECTS
For presets with a delay effect, the footswitch has a tap tempo function for
hands-free adjustment of delay rates. To do this, first put the footswitch in
BANK 1 or 2 mode as described above. Select a preset with a delay effect; step
on the footswitch button corresponding to the current selected preset twice or
more at the desired tempo. This changes the delay time in the same manner as
tapping the TAP tempo utility button on the amp’s control panel (page 12).
IMPORTANT: If delay rate changes are not saved, the preset in use will
revert to its original delay rate when returning to the preset after leaving
it, or when turning the amplifier off and back on again. To save delay rate
changes in a preset, follow the SAVE, SAVE AS or REPLACE instructions on pages
6 and 7.
FOOTSWITCH: TUNER
To use the footswitch for hands-free tuning, step on buttons “C” and “D”
simultaneously to activate chromatic tuner mode. Note that putting the
footswitch in tuner mode also activates the tuner display on the Mustang LT50
control panel (page 16). The pitch letter closest to the sounded note will
appear in the footswitch display window (symbols to the right of each pitch
letter denote sharp and flat notes; when tuning to, for example, C sharp or E
flat). When sounding a note, the LEDs above footswitch buttons “A” and “B”
illuminate red to indicate degrees of flatness; the LEDs above footswitch
buttons “C” and “D” illuminate red to indicate degrees of sharpness. When the
correct pitch is attained, the centre LED beneath the footswitch display
window will illuminate green. When tuning is complete, step on any button to
exit tuner mode. Note that the footswitch tuner uses mute speaker output.
- To activate the footswitch tuning function, step on buttons “C” and “D” simultaneously (double yellow arrow).
- In the example above, a “G” note is displayed as being particularly flat, as indicated by the illumination of the red LED above button “A” (green arrow).
- Here, the “G” note is displayed as slightly sharp, as indicated by the illumination of the red LED above button “C” (green arrow)
- Here, the “G” note is at the correct pitch, as indicated by the illumination of the green centre LED (green arrow). When tuning is complete, step on any button to exit the footswitch tuner mode.
MENU FUNCTION: LEVELS
The third MENU function—LEVELS—features a level control for use when recording
using the USB port (page 23) on the control panel, and for the mono line
output (page 23) when connected to external sound and recording equipment.
Note that the MASTER VOLUME control does not control USB and mono line output
volume. To access this option, press the MENU utility button and use the
ENCODER to scroll to and select LEVELS. The
level control is automatically highlighted:
Turn the ENCODER to set a new “LEVEL” value. Press the ENCODER to accept the new value and exit the menu. Alternately, press the BACK utility button (green arrow) to accept the new value and return to the MENU function screen:
For best sound quality, set the “LEVEL” so that the signal stays within the green bars, and barely reaches the single yellow bar at the right, and does not reach the single longer red clipping bar at the far right (all bars shown illuminated in the illustration above). Note that changing presets can change individual volumes; “LEVEL” readjustment may be necessary when changing presets.
MENU FUNCTION: RESTORE
The fourth MENU function—RESTORE—enables the restoration of all original
factory presets and amplifier settings. To do this, press the MENU utility
button, then use the ENCODER to scroll to and select RESTORE: To initiate
restoration use the ENCODER to scroll to and select “YES RESTORE”. To cancel
restoration, press the ENCODER on “NO CANCEL”, or press the BACK utility
button. While restoration is in progress, a blue waiting screen
with a progress bar will appear. When restoration is complete, the user is
returned to the first preset screen:
MENU FUNCTION: ABOUT
The fifth MENU function—ABOUT—displays the amp’s current firmware version. To
do this, press the MENU utility button, then use the ENCODER to scroll to and
select ABOUT; the current firmware version will be displayed:
AUXILIARY INPUT AND HEADPHONE OUTPUT
The Mustang LT50 control panel features two 1/8”-inch jacks: an auxiliary
input for connecting external mobile/audio devices and an output for
convenient headphone use. Note that when using the auxiliary input, volume
levels for external devices are set using volume controls on the external
devices themselves (the amp’s volume controls are for overall volume level
only and do not affect the individual volume of external devices connected to
the auxiliary input jack). Also note that speaker output is muted when
headphones are plugged in, and that the auxiliary input signal is not sent to
the USB port or mono line output.
USB PORT
The Mustang LT50 control panel features a USB port for audio recording and Fender TONE use (see “FENDER TONE” below). Using a micro USB cable (not included), connect a computer with recording software to this port. No external driver is needed to connect to an Apple computer. To connect to a Windows-based computer, the user must download the ASIO driver setup with a Fender Mustang device, available at https://support.fender.com/hc/en- us/articles/214343123-How-do-I-know-which-ASIO-Driver-to-use. Note that although the USB port and the auxiliary input can be used simultaneously, the USB port cannot be used to record a signal from the auxiliary input. Also note that the USB output is in stereo and that while preset gain, volume and tone controls will affect USB level and tone, the MASTER VOLUME control does not.
When recording using the USB port, a level control is located in the LEVELS menu function (page 21). Mustang LT50 has a rear-panel 1/4” mono line output for connection to external sound and recording equipment. When using the rear- panel mono line output, a level control for it is located in the LEVELS menu function (page 21). Note that preset gain, volume and tone controls will affect mono line output level and tone; the MASTER VOLUME control does not affect mono line output level. Also, note that a TRS (stereo) cable can be used to reduce or eliminate hum.
MONO LINE OUTPUT FENDER TONE™
Fender Tone—the ultimate desktop companion to Mustang LT amplifiers for Mac
and PC—is available as a free download from fender.com/ToneDesktop. With an
easy-to-use interface, Tone users can have convenient control over existing
Mustang LT50 functions, plus access to additional presets and many other
features, including:
- Firmware updates
- Dozens of additional Fender presets for auditioning and downloading
- Preset creation and editing with a convenient “undo” feature
- Preset editing (replacing amp and effect models, and modifying parameters)
- Preset saving, renaming, moving and clearing
- Preset backup and restore
- Effect bypass
Learn more about Fender Tone at fender.com/ToneDesktop, and find support materials at fender.com/ToneSupport
SPECIFICATIONS
- TYPE PR 5674
- POWER REQUIREMENTS 110 watts
- POWER OUTPUT 50 watts into 8Ω
- INPUT IMPEDANCE 1MΩ (instrument) 15kΩ (aux)
- SPEAKER One 12” Fender Special Design speaker (8Ω)
- FOOTSWITCH Four-button MGT-4 (optional, PN 0994071000)
- DIMENSIONS AND WEIGHT Width: 17” (43.1 cm) Height: 16.5” (41.9 cm)
- Depth: 8.5” (21.6 cm) Weight: 19.8 lbs. (9 kg)
Product specifications are subject to change without notice. Be sure to check fender.com/firmware/support regularly for firmware updates that improve and enhance the Mustang LT50 experience.
Download PDF: Fender LT50 Mustang Guitar Speaker User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>