FenderHDly Fender Hammertone Delay Pedal User Manual

FenderHDly Fender Hammertone Delay Pedal

OVERVIEW

HAMMERTON DELAY

Thank you for purchasing the Hammertone Pedal

• Delay, a versatile delay effect that adds dimension and ambiance to your sound.
• Enter a world of delay possibilities with time control possibilities, feedback and level. Use the switch
• Type to choose between digital delay and analog and use the Mod switch to enable and disable modulation. The delay effect is an essential item in the arsenal of any modern guitarist, and the Hammertone pedal
• Delay puts that shimmering sound at your feet in all its nuances, from the most subtle to the most striking.

INSTRUCTION

• OUTPUT JACK
  Low impedance output for connection to amp or pedal next in the signal chain.

• INPUT JACK
  High impedance input for electric guitar, bass, guitars acoustics with microphones, keyboards and other instruments.

• EXTERNAL DC POWER CONNECTOR SOCKET
  Standard socket for connecting a 9V DC power supply appropriate, central negative pole.

• TIME BUTTON
  Delay time adjustment knob, up to a maximum of one second.

• FEEDBACK BUTTON
  Feedback adjustment knob for adjusting the volume of the signal repetitions. At maximum, repetitions will continue to increase in volume instead of disappearing naturally and will eventually become loud enough to cause a pleasant distortion.

• LEVEL BUTTON
  Level control knob for adjusting the volume of repetitions, from completely dry (no delay signal) to one (equal volume for repeated and dry signals).

• TYPE SWITCH
  Three position switch for digital delay sound (top), a darker analog delay sound 1 (middle) and a delay sound analog 2 plus mid (low).

• MOD SWITCH
  Switch for activating the modulation effect setting on signal repetitions.

• LEDs
  The indicator LED is lit when the effect is active.

• FOOTSWITCH
  Activates and deactivates the effect

INTERNAL ADJUSTABLE POTENTIOMETERS

(ACCESSIBLE BY REMOVING THE BACK COVER)

• The SPEED potentiometer adjusts the rate of modulation when the MOD switch is active.
• The DEPTH knob adjusts the modulation depth when the
• MOD switch is active.
• Remove the cover using a flathead screwdriver and adjust the potentiometers using a Phillips screwdriver.
• Try temporarily adjusting a short delay by adjusting the control modulation. The amount of modulation remains constant for delays short and long, but the modulation delay stays ahead of the delay major. It may seem slower by setting a longer delay with the potentiometers.

A PRODUCT OF FENDER MUSICAL INSTRUMENTS CORPORATION CORONA, CALIFORNIA, USA
Fender® is a registered trademark of FMIC. Copyright © 2021 FMIC. All rights reserved.
PN 7724429000 REV B

IMPORTANT SAFETY INSTRUCTIONS

• WARNING: To prevent damage, fire or electric shock, never expose the device or its power supply to rain or moisture.
• Do not modify the mains plug of the power adapter.
• Do not drip or splash liquids on the device.
• There are no parts that can be repaired by the user, entrust this task only to a Qualified staff.
• WARNING : The device should only be connected to a power source (adapter) safety agency approved, approved for use with device and complies with the safety requirements of local regulations and applicable national laws.
• Unplug the AC adapter before cleaning the exterior of the unit. Do not use cleaning only with a damp cloth, then wait until the appliance is completely dry before plugging it back in.
• Amplifiers and loudspeaker systems, as well as earphones and headphones (the applicable) are capable of producing very high sound pressure levels likely to cause temporary or permanent hearing damage. Done
• Be careful when setting and adjusting the volume level while in use

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. THE OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING WHICH MAY CAUSE ADVERSE EFFECTS.

OTHER LANGUAGES
The user manual is available in other languages at www.fender.com/support

FEATURES

• IMPEDANCES Input: 500k Output: 470
• FOOD Regulated power supply 100 mA min at 9 Vdc barrel connector 5.5 x 2.1 mm (not included)
• POWER REQUIRED 9 V DC
• DIMENSIONS 62mm x 111.8mm x 55.9mm (2.44” x 4.4” x 2.2”)
• WEIGHT 0.23 kg (0.50 lbs)

Product subject to change without notice

References

• Home  · Customer Self-Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>