QUOIZEL LWS7970D2 Sumpter 4 Light Matte Black Pendant User Guide

QUOIZEL LWS7970D2 Sumpter 4 Light Matte Black Pendant

Product Information

Specifications

• Crossbar Assembly: 1pc
• Wire Connector: 3pcs
• Outlet Box Screw: 2pcs
• Quick Link: 2pcs
• Ceiling Canopy: 1pc
• Fixture Chain: 1pc
• Fixture Loop: 1pc
• Socket Assembly: 1pc
• Large Ring: 1pc
• Ring: 1pc

Product Usage Instructions:

Step 1: Adjusting fixture chain length

1. Pull the supply wires and ground wire up through the fixture chain alternating links.
2. Push the ends of the supply wires and ground wire up throughthe loop and into the outlet box.
3. Remove the canopy.
4. Insert the remaining slack wire into the outlet box.

Step 2: Wiring
Connect the wires as follows:

• Black or red wire (hot) from the outlet box to the black wire of the fixture.
• White wire (neutral) from the outlet box to the white wire of the fixture.
• Ground wire from the fixture with the label G to the ground wire of the outlet box.

Step 3: Installing the Fixture

1. Attach the crossbar assembly to the outlet box using the outlet box screws.
2. Attach the fixture loop to the crossbar assembly using the quick links.
3. Attach the ceiling canopy to the fixture loop.
4. Attach the fixture chain to the ceiling canopy.
5. Hang the fixture on the fixture loop.

Care and Maintenance
To ensure the longevity of your product, please follow these care and maintenance guidelines:

• Regularly clean the fixture with a soft, dry cloth.
• Avoid using harsh chemicals or abrasive materials on the fixture.
• Check and tighten any loose screws or connections periodically.

FAQ

Q: What should I do if the light bulb is not working?
A: Replace the light bulb with a new one.

Thank you for purchasing this QUOIZEL product.
If you have any questions or problems, please call our customer service department, 8:30 a.m. – 5:00 p.m., EST, Monday – Thursday, 10:20 a.m. – 5:00 p.m., EST, Friday.
For the quickest response, please visit Quoizel.com and click on Contact Us.

• 1-844-564-3055
• E-mail : cs@quoizel.com

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product

WARNING

• RISK OF ELECTRIC SHOCK – Before beginning installation, turn off electricity at the circuit breaker box or the main fuse box.
• RISK OF FIRE – Use bulbs specified by the markings and/or labels on the fixture.

CAUTION

• For your safety, read instructions completely before beginning installation.
• If in doubt about electrical installation, consult a licensed electrician.
• Turn off electricity to fixture before replacing the bulb(s).

PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

LIGHT SOURCE
4 BULBS REQUIRED (SOLD SEPARATELY)

• Please check with bulb manufacturer for dimming capabilities.

TOOLS REQUIRED

PACKAGE CONTENTS

Installattion

If the ceiling canopy is not snug against the ceiling, remove it from the crossbar assembly. Adjust the length of the pre-assembled nipple by unscrewing the pre-assembled hex nut. Screw the nipple in or out of the crossbar until the correct length is achieved. Then, re-attach the ceiling canopy.

• A Adjust fixture chain length.
• B – C Install fixture chain.

• A – Pull the supply wires and ground wire up through the fixture chain alternating links.
• B – Push the ends of the supply wires and ground wire up through the loop and into the outlet box.
• C – Remove the canopy.
• D – Insert the remaining slack wire into the outlet box.
• Trim excess fixture wire leaving a minimum of 6 inches hanging out of the outlet box.
• Separate the smooth side and ribbed side of supply wire.
• Using wire strippers, strip each wire 1/2 inch from the end.

CARE AND MAINTENANCE

Wipe clean using soft, dry cloth or static duster. Always avoid using harsh chemicals and abrasives to clean fixture as they may damage the finish.

TROUBLESHOOTING

PROBLEM| POSSIBLE CAUSE| CORRECTIVE ACTION|
---|---|---|---
The lights will not turn on.

|

1. Bulb is burned out.
2. Power is off.
3. Faulty wire connection.
4. Faulty switch.

|

1. Replace light bulb.
2. Make sure power supply is on.
3. Check wiring. Vérifiez le câblage. /
4. Test or replace the switch.

|
Fuse blows or the circuit breaker trips when light is turned on.

|
Crossed wires or power wire is grounding out.

|
Check wire connection. Vérifiez les connexions. /

|

References

• Quoizel | Artisans In Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>