ORION 42HSDI3G Full HD High Performance Multi Input LED Monitor User Guide

ORION 42HSDI3G Full HD High Performance Multi Input LED Monitor

SAFETY INSTRUCTION
Follow this safety instruction to use the monitor properly and prevent the damages

This safety instruction has “Warning” & “Caution” as below
Warning – If the user does not follow this instruction, it may cause the serious damage to the user.
Caution – If the user does not follow this instruction, it may cause the slight Keep this user’s guide book for later use.

Warning

• Never remove the back over and touch the inside of the monitor. If you need a service, please contact the service center
• Keep away the monitor from the direct sunlight and a heating appliance.
• Never push objects of any kind into this product as they may result in a risk of fire or electric shock.
• Connect the power code to the wall outlet tightly. If the power code or plug are defective and the wall outlet is not tight, please do not use them.
• Do not install this monitor on the outside and near water. If may cause damage to the product, electric shock and fire.
• For cleaning do not use liquid cleaners. Never touch the power plug with wet-hands.
• When lightning and thundering, unplug the monitor from the wall outlet and never touch it.
• Unplug this product from the wall outlet, when It does not operate for a long time.
• When smoking and noising from the monitor, unplug the product from the wall outlet and contact a service center.

WARNING : How to fix
Do not open this product as it contains high voltage inside. It may create an electric shock. It the user disassembles and remove the back cover, it does not make sure to make up for the damages and do a service and exchange the monitor.

Cautions

• Install this monitor some distance From the wall and do not install unless Proper ventilation is provided. Place this product on a stable place. If not, it may fall, causing serious Damages to the monitor and people.
• The openings must not be blocked by curtain, rug or other similar surface. Before carrying the monitor, tum it off and Unplug the signal cables and the power code From the wall outlet.
• When carrying this monitor, be careful not to damage the panel and drop it It may cause some trouble. Take the power plug out from the wall outlet.
• Do not pull the cable. It may snap the inner wires and cause overheating and fire
• Install this monitor about 50cm far from the eyes and an angle of 0~15 degrees below eyes. Too close installation may cause having weak sight.
• Do not press the LCD panel with hands or the sharpened material hardly.
• Do not use the chemical liquid for cleaning.
• It may cause fading and breakage.
• For cleaning, unplug the monitor from the Wall outlet. Do net use the liquid cloth.
• Use the soft cloth.

WARNING
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR WATER. Instructions for Disposal of Electrical and Electronic Equipment in Private Households.

Disposal of used Electrical and Electronic Equipment
(Applicable in the European Union and other European countries with garbage separate disposal and collection methods) This symbol on the product, or in the related documents in the package, indicates that this product shall not be treated as normal household waste. Instead, it should be taken to a proper applicable collection point or depot for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent possible negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city authority, your household waste disposal service or the place where you purchased the product.

FCC RF INTERFERENCE STATEMENT

NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio, TV technician for help.
• Only shielded interface cable should be used.

Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment.

DOC COMPLIANCE NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the radio interference regulation of Canadian Department of communications.

INSTALLATION

Parts

How to Install

KEY BUTTON

CONNECTION

1. DC12V
   DC adapter input

2. AUDIO (PC)
   Stereo audio input for VGA

3. COMPONENT
   TRIGGER
   COMPONENT (Y/Pb/Pr) signal & stereo audio input

4. AUDIO (CVBS-2)
   Stereo audio input for CVBS-2

5. AUDIO (CVBS-1 / S-VIDEO)
   Stereo audio input for CVBS-1 or S-VIDEO

6. S-VIDEO IN / OUT
   S-VIDEO signal input / looping out

7. CVBS-2 IN / OUT
   CVBS-2 signal input / looping out

8. CVBS-1 IN / OUT
   CVBS-1 signal input / looping out

9. TRIGGER
   TRIGGER signal input

10. HDMI
    HDMI signal 1 / 2 input

11. DVI
    DVI signal input

12. VGA
    VGA (PC RGB) signal input

13. 3G-SDI IN / OUT
    3G-SDI signal input / looping out

14. AC POWER
    AC100~240V input

REMOTE CONTROLLER

• MODE SELECT MENU
  CVBS1

• Select CVBS1 mode
  CVBS2

• Select CVBS2 mode
  S-VIDEO

• Select S-VIDEO mode
  VGA (RGB)

• Select VGA mode
  DVI

• Select DVI mode
  HDMI1

• Select HDMI1 mode
  COMPONENT

• Select COMPONENT mode
  SDI

• Select 3G-SDI mode
  HDMI2

• Select HDMI2 mode

OSD CONTROL MENU

• POWER
  Turn ON / OFF the monitor

• MUTE
  Turn ON / OFF the sound

• AUTO
  Auto adjust position of the screen (in VGA mode)

• COLOR TEMPERATURE
  Select color temperature of the screen

• SCAN MODE
  Select the scan mode of the screen

• VOL- / VOL+
  Increase / Decrease the volume level

• MENU / EXIT
  Activate and exit the OSD menu

• STILL
  Freeze the current image

• KEY LOCK
  Locking the button (Prevent operation)

PIP CONTROL MENU

• S. SET
  Select between main and PIP audio input

• PIP
  Activates PIP/PBP mode

• P. INPUT
  Select an input source for PIP mode

• P. LOCATION
  Select a location for PIP mode

• P. SIZE
  Select a size for PIP mode

• P. SWAP
  Swap between main and PIP input

OSD MENU SETTING

4-1 Mode Setting

Inputs can be set to CVBS1, CVBS2, S-VIDEO, RGB PC, DVI, HDMI1, HDMI2, 3G-SDI & COMPONENT mode

1. Use SOURCE button and then button to move the source.
2. Press the button to select the source.
3. Press the MENU/EXIT button to exit the INPUT menu.

• CVBS1
  Select CVBS1 mode

• CVBS2
  Select CVBS2 mode

• S-VIDEO
  Select S-VIDEO mode

• RGB PC
  Select VGA mode

• DVI
  Select DVI mode

• HDMI1
  Select HDMI1 mode

• 3G-SDI
  Select 3G-SDI mode

• COMPONENT
  Select COMPONENT mode

• HDMI2
  Select HDMI2 mode

Menu Setting (CVBS, S-VIDEO, COMPONENT Mode)

PICTURE

1. Press the MENU/EXIT key to access menu.
2. Use the arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use the arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item

CONTRAST : Adjust visual color contrast
COLOR : Adjust visual color of screen
SHARPNESS : Adjust sharpness of screen
BRIGHTNESS : Adjust color brightness
TINT : Adjust tint of color
COLOR TEMP : Switch color temperature of screen

USER – Default setting of RED, GREEN, BLUE is 50% and adjustable from range of 0 to 100%

SCREEN

1. Press the MENU/EXIT key to access menu.
2. Use the arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use the arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item.

ON – PIP INPUT : Select an input source for PIP mode

(CVBS1, CVBS2, S-VIDEO)
PIP SWAP : Swap between main and PIP input
PIP SIZE : Select a size for PIP mode
(SMALL, NORMAL, LARGE)
PIP R/T : Select a location for PIP mode
(R/B, L/B, R/T, L/T)

SETUP

INPUT : Select an input source for main screen LANGUAGE : Set to different language mode
SOUND MUTE : Turn on/off the sound BUTTON LOCK : Locking the button (Prevent operation)
NOISE REDUCTION : Set a noise reduction mode OSD TIME : Set a time duration of OSD menu
DEFAULT : Factory default setting LINE SHIFT : Move a little to protect the screen

CYCLE SETUP

1. Press the MENU/EXIT key to access menu.
2. Use the arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use the arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item.

CYCLE TIME : Adjust cycle time to displayed on the screen

CYCLE : Selected mode keep change continuously

TIGGER

1. Press the MENU/EXIT key to access menu.
2. Use the arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use the arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item.

4-3 Menu Setting (VGA Mode)

PICTURE

Default setting is 60% and adjustable from range of 0 to 100% Default setting is 50% and adjustable from range of 0 to 100%

1. Press the MENU/EXIT key to access menu.
2. Use the arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use the arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item.

USER
Default setting of RED, GREEN, BLUE is 50% and adjustable from range of 0 to 100%

SCREEN

1. Press the MENU/EXIT key to access menu.
2. Use the arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use the arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item.

ON – PIP INPUT : Select an input source for PIP mode (CVBS1, CVBS2, S-VIDEO)
PIP SWAP : Swap between main and PIP input

PIP SIZE : Select a size for PIP mode
(SMALL, NORMAL, LARGE)
PIP R/T : Select a location for PIP mode (R/B, L/B)

SETUP

1. Press the MENU/EXIT key to access menu.
2. Use the arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use the arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item.

RGB SETUP

1. Press the MENU/EXIT key to access menu.
2. Use the arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use th arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item.

H-POSITION : Adjust horizontal position of monitor V-POSITION : Adjust vertical position of monitor

CLOCK : Adjust clock of monitor PHASE : Adjust phase of monitor

AUTO ADJUST : Auto adjust position of screen POWER SAVING : Power saving mode

AUTO REPEAT : Adjust auto repeat of monitor

CYCLE SETUP

1. Press the MENU/EXIT key to access menu.
2. Use the arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use the arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item.

TRIGGER

1. Press the MENU/EXIT key to access menu.
2. Use the arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use the arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item.

VGA / DVI / HDMI / SDI Mode Tables

Note
Not all resolutions generated by your video source are available on the monitor.

4-4 Menu Setting (DVI, HDMI, 3G-SDI Mode)

__

__

__

__

VGA / DVI MODE

| __

VGA

| 720X400| 70
640X480| 60 / 72 / 75
SVGA| 800X600| 50 / 60 / 72 / 75
XGA| 1024X768| 50 / 60 / 75
WXGA| 1366X768| 60
UXGA| 1600X1200| 60
HD| 1920X1080| 60
__

__

__

__

HDMI MODE

| EDTV 480i| 720X480| 30
EDTV 576i| 720X576| 25
SDTV 480p| 720X480| 60
SDTV 576p| 720X576| 60
HDTV 720p| 1280X720| 50 / 60
HDTV 1080i| 1920X1080| 25 / 30
HDTV 1080p| 1920X1080| 50 / 60
__

__

__

__

SDI MODE

| __

SD

| 480i| 59.94
576i| 50
__

__

HD

| 720p| 23.98 / 24 / 25 / 29.97 / 30 / 50 / 59.94 / 60
1080i| 50 / 59.94 / 60
1080p| 23.98 / 24 / 25 / 29.97 / 30
1080psf| 23.98 / 24 / 25 / 29.97 / 30
3G| 1080p| 50 / 59.94 / 60

PICTURE

Default setting is 60% and adjustable from range of 0 to 100% Default setting is 50% and adjustable from range of 0 to 100%

1. Press the MENU/EXIT key to access menu.
2. Use the arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use the arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item.

CONTRAST : Adjust visual color contrast

COLOR : Adjust visual color of screen

SHARPNESS : Adjust sharpness of screen
BRIGHTNESS : Adjust color brightness

TINT : Adjust tint of color
COLOR TEMP : Switch color temperature of screen
Default setting is MEDIUM and switch to WARM, USER and COOL color temperature options
USER – Default setting of RED, GREEN, BLUE is 50% and adjustable from range of 0 to 100%

Default setting is 1080p and switch to 1920X1080 mode
1080P – Bluray, DVD player and AV video equipment (2% Over Scan)
1920X1080 – It is the fit image on PC In (Just/Real Scan)

SCREEN

1. Press the MENU/EXIT key to access menu.
2. Use the  arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use the arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item.

SETUP

1. Press the MENU/EXIT key to access menu.
2. Use the arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use the arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item.

CYCLE SETUP

1. Press the MENU/EXIT key to access menu.
2. Use the arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use the arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item.

TRIGGER

1. Press the MENU/EXIT key to access menu.
2. Use the arrow to highlight a selection.
3. Press the SELECT to choose an item.
4. Use the arrow to highlight a selection.
5. Use the arrow to adjust the setting on a selected item.

FEATURE

Noise reduction

| Y

Y (NO/NC)

Y

| Y

Y (NO/NC)

Y

| Y

Y (NO/NC)

Y

 | Auto source sequencing| Y| Y| Y
 | Multi Lingual Language| Eng, Spa, Fre, Ger, Ita| Eng, Spa, Fre, Ger, Ita| Eng, Spa, Fre, Ger, Ita
Dimension| Outline Dimension (w Stand)| 24.9216.756.30 inches| 28.8219.146.30 inches| 37.9524.579.45 inches
Cabinet| Cabinet color/Base Stand

Cabinet Material

| Black/Desktop Stand

Electro-Galvanized Steel

| Black/Desktop Stand

Electro-Galvanized Steel

| Black/Desktop Stand

Electro-Galvanized Steel

Power| Electrical Ratings| AC 100~240 V (50/60Hz)| AC 100~240 V (50/60Hz)| AC 100~240 V (50/60Hz)
Circumstance| Operating Temperature

Storage Temperature

| 0~50 celsius

-20~60 celsius

| 0~50 celsius

-20~60 celsius

| 0~50 celsius

-20~60 celsius

__

Mounts

| VESA Mounts Size Ceiling Mount Wall

Rack Mount

| 100100/200100 mm CMK-01

WB-31, 2642

N/A

| 200*200 mm CMK-01 with FMA-01

WB-2642

N/A

| 400*300 mm CMH-01 WB-2642

N/A

TROUBLESHOOTING

The screen doesn’t show up

| 1. Make sure if the power supply is connected property
2. Turn on the power.
3. Select the input signal right for the connected port.
The screen is too light or to dark|

Control the BRIGHTNESS

The screen size is not fit for the PC signal| Press the AUTO key among keys in the front. (It is used only in the PC signal)
The screen color shows strange in the PC signal| In the FUNCTION menu of OSD menu, perform the AUTOADJUST.

When the following troubles are occurred, follow the trouble shooting. Before contacting a service center.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>