VIVOTEK IP7161 Network Camera Installation Guide

June 17, 2024
Vivotek

Quick Installation Guide
IP7161
2-megapixel . Day & Night
Network Camera

VIVOTEK IP7161 Network Camera -

Warning Before Installation

  • Power off the Network Camera as soon as smoke or unusual odors are detected.
    Contact your distributor in the event of occurrence.

  • Do not place the Network Camera around heat sources, such as a television or oven.

  • Keep the Network Camera away from direct sunlight.

  • Keep the Network Camera away from water. If the Network Camera becomes wet, power off immediately.
    Contact your distributor in the event of occurrence.

  • Refer to your user’s manual for the operating temperature.

  • Do not place the Network Camera in high humidity environments.

  • Do not place the Network Camera on unsteady surfaces.

  • Do not disassemble the Network Camera.

  • Do not insert sharp or tiny objects into the Network Camera.

  • Do not touch the Network Camera during a lightning storm.

  • Do not drop the Network Camera.

Package Contents

  • IP7161

  • Camera Stand

  • Quick Installation Guide

  • Warranty Card

  • Power Adapter

  • CS-mount Lens

  • Software CD

  • L-type Hex Key Wrench

Physical Description

  • Front Panel
    VIVOTEK IP7161 Network Camera - Front Panel

  • Back Panel
    VIVOTEK IP7161 Network Camera - Back Panel

  • Lens
    VIVOTEK IP7161 Network Camera - Lens

Mounting the Lens to the Camera

  1. Mount the lens by turning it clockwise onto the camera mount until it stops. If necessary, turn the lens counterclockwise slowly until it gets the best attitude.
  2.  Connect the lens cable plug to the camera connector.

VIVOTEK IP7161 Network Camera - cable plugFor further setup, please refer to the lens’ instruction manual inside the lens package.

Network Deployment

General Connection (without PoE)

  1. If you have external devices such as sensors and alarms, connect them to the general I/O terminal block.
  2.  Connect the camera to a switch via Ethernet cable.
  3. Connect the power cable from the Network Camera to a power outlet.

VIVOTEK IP7161 Network Camera - power outlet

Power over Ethernet (PoE)

  • When using a PoE-enabled switch
    The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable.

VIVOTEK IP7161 Network Camera - power outlet1

  • When using a non-PoE switch
    Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch.

VIVOTEK IP7161 Network Camera - Power Injector

Assigning IP Address

  1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.

  2.  The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program.
    VIVOTEK IP7161 Network Camera - software CD

  3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN.

  4.  After searching, the main installer window will pop up. Click on the MAC that matches the one labeled on the bottom of your device to connect to the Network Camera via Internet Explorer.
    VIVOTEK IP7161 Network Camera - software CD1

Ready to Use

  1. Access the Network Camera from the LAN.

  2. Retrieve live video through a web browser or recording software.
    VIVOTEK IP7161 Network Camera - web browser

  3. Unscrew the zoom controller to adjust the zoom factor. Upon completion, tighten the zoom controller.

  4.  Unscrew the focus controller to adjust the focus range. Upon completion, tighten the focus controller.

For further setup, please refer to the user’s manual on the software CD.

Fine-tune the Camera Focus

Please follow the steps below to fi ne-tune the camera focus:

  1. Use the supplied L-type hex key wrench to loosen the ring screw; the adjustment ring will become rotatable.
  2.  Rotate the adjustment ring to fi ne-tune the distance between the sensor and the lens; the IR-cut fi lter and image sensor will move forwards or backwards as the illustration shows below.
  3.  When fi nished, tighten the ring screw to fi x the adjustment ring.

VIVOTEK IP7161 Network Camera - sensor

WWW.VIVOTEK.COM

P/N:625008300G Ver.1.02
Copyright 2009 © VIVOTEK INC. All rights reserved.
6F, No 192, Lien-Cheng Rd., Chung-Ho, Taipei County, Taiwan T : +886 2 82455282 F : +886 2 82455532 E : sales@vivotek.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals