EDiMAX BR-6428HPN Wireless Broadband Router User Manual

EDiMAX BR-6428HPN Wireless Broadband Router

Product Information

Specifications

• Broadband router
• 3dBi antenna (2 pcs)
• Quick installation guide (1 pcs)
• CD with multi-language QIG and user manual (1 pcs)
• 12V DC power adapter (1 pcs)
• Ethernet cable (1 pcs)
• Power adapter (1 pcs)
• Vertical stand (1 pcs)
• Accessory kit (1 pcs)

Getting Familiar with Your New Wireless Broadband Router

Front Panel

Back Panel

• Antenna connector(s): Connects to the supplied antenna(s)
• Wi-Fi on/off switch: Switches on/off the Wi-Fi signal
• WPS/Reset Button: Resets the router to factory default settings or starts WPS function (press this button and hold for 20 seconds to clear all settings or press this button for 2-5 seconds to activate WPS function)
• 1-4 (LAN Ports): Connects to computer or other web devices
• WAN Port: Connects to computer or other web devices
• Power Connector

FAQs

• Q: Where can I find the firmware files for this product?
  • The firmware files for this product can be found under the Download page at the Edimax website (www.edimax.com).
• Q: How do I reset the router to factory default settings?
  • To reset the router to factory default settings, press and hold the WPS/Reset Button for 20 seconds.
• Q: How do I activate the WPS function?
  • To activate the WPS function, press the WPS/Reset Button for 2-5 seconds.

BR-6428HPn User Manual
05-2012 / v1.0
y

COPYRIGHT

Copyright © Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd.
Edimax Technology Co., Ltd. makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability, or fitness for any particular purpose. Any software described in this manual is sold or licensed as is. Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Edimax Technology Co., Ltd. reserves the right to revise this publication and to make changes from time to time in the contents hereof without the obligation to notify any person of such revision or changes.
The product you have purchased and the setup screen may appear slightly different from those shown in this QIG. For more information about this product, please refer to the user manual on the CD-ROM. The software and specifications are subject to change without notice. Please visit our website www.edimax.com for updates. All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.
Notice According to GNU General Public License Version 2
This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
The GNU GPL and GNU LGPL software codes used in Edimax products are distributed without any warranty and are subject to the copyrights of their respective authors. The firmware files for this product can be found under the “Download” page at the Edimax website (www.edimax.com).

CHAPTER I:

PRODUCT INFORMATION

Before you start using this router, please check if there is anything missing in the package, and contact your dealer to claim the missing item(s):
z Broadband router (1 pcs) z Quick installation guide (1 pcs) z 3dBi antenna (2 pcs) z CD with multi-language QIG and user manual (1 pcs) z 12V DC power adapter (1 pcs) z Ethernet cable (1 pcs) z Power adapter (1 pcs) z Vertical stand (1 pcs) z Accessory kit (1 pcs)
1-2 Getting Familiar with Your New Wireless Broadband Router

Front Panel

LED Name PWR
Wireless
WAN
LAN (1-4)

Light Status On Off On Off Flashing On Off Flashing On Off Flashing

Description Router switched on and correctly powered Router not powered or not correctly powered Wireless connectivity activated Wireless connectivity not activated Wireless LAN activity (transferring data) WAN port connected WAN port not connected WAN activity (transferring data) LAN port connected LAN port not connected LAN activity (transferring data)

4
y

Back Panel

Item Name Antenna
connector(s) Wi-Fi on/off
switch WPS/Reset
Button
1-4 (LAN Ports) WAN Port
Power Connector

Description Connects to the supplied antenna(s)
Switches on/off the Wi-Fi signal
Resets the router to factory default settings or starts WPS function (press this button and hold for 20 seconds to clear all settings or press this button for 2-5 seconds to activate WPS function) Connects to computer or other web devices
Connects to cable/xDSL modems Connects to the supplied power adapter

5
y

CHAPTER II:

SYSTEM AND NETWORK SETUP

2-1 Establishing a Network Connection Please follow the following instructions to build a network connection between your new broadband router, computers, and other network devices:
1. Connect your xDSL or cable modem to the router’s “WAN” port with an Ethernet cable.
2. Connect your computer to one of the router’s “LAN” ports with an Ethernet cable.
3. Connect the power adapter to the wall socket, and then connect it to the “12V” socket on the back panel of the router.
6
y

4. Please check all the LEDs on the front panel. The “PWR” and “WAN” LEDs should be on. The “LAN” LED should be on if the computer is connected and correctly powered. If you encounter any problems, please make sure that all your devices are connected and powered correctly.
   2-2 Setting Client Computers to Obtain IP Addresses Automatically

Before you start configuration procedures, your computer must be able to get an IP address automatically (set to use dynamic IP addresses). If your computer is set to use a static IP address, or if you are unsure, please follow the following instructions to configure your computer to use dynamic IP addresses:

z Windows 95/98/Me z Windows 2000 z Windows XP z Windows Vista

(see section 2-2-1) (see section 2-2-2) (see section 2-2-3) (see section 2-2-4)

2-2-1 Windows 95/98/Me IP Address Setup

1. Click the “Start” button (it should be located at the lower-left corner of your screen), then click “Control Panel”. Double-click the “Network” icon, and the
   “Network” window will appear. Select “TCP/IP”, and then click “Properties”.

7
y

2. Select “Obtain an IP address from a DHCP server”, then click “OK”.
   2-2-2 Windows 2000 IP Address Setup 1. Click the “Start” button (it should be located at the lower-left corner of your screen), then click “Control Panel”. Double-click the “Network and Dial-up Connections” icon, and then double-click “Local Area Connection”. When the
   8
   y

“Local Area Connection Properties” window appears, select “Internet Protocol (TCP/IP)”, and then click “Properties”.
2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”.
2-2-3 Windows XP IP Address Setup 1. Click the “Start” button (it should be located at the lower-left corner of your screen), then click “Control Panel”. Double-click the “Network and Internet Connections” icon, click “Network Connections”, then double-click “Local Area
9
y

Connection”. When the “Local Area Connection Properties” window appears, click “Properties”.
2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”.
2-2-4 Windows Vista IP Address Setup 1. Click the “Start” button (it should be located at the lower-left corner of your screen), then click “Control Panel”. Click “View Network Status and Tasks”, and then click “Manage Network Connections”. Right-click “Local Area Network”, then
10
y

select “Properties”. When the “Local Area Connection Properties” window appears, select “Internet Protocol Version 4 (TCP/IPv4)” and then click “Properties”.
2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”.
11
y

2-3 Connecting to Broadband Router via Web Browser You can access the broadband router’s web-based configuration interface via any connected computer with a web browser (Internet Explorer 5.x or above, Firefox, Opera, or Safari).
1. Please input “192.168.2.1” in the web browser’s address bar and press “Enter”.
2. You should see the following authentication window:
NOTE: If you cannot access the broadband router’s web-based configuration interface, the IP address you have inputted may be incorrect. If you have previously changed the router’s IP address, please input the one you have designated. 3. Please input “admin” in the “Username” field and “1234” in the “Password” field. Click the “OK” button to enter the web configuration interface.
12
y

4. The first page you see after logging in is “Home”. You can see all the current settings and other system information here.

System

Model

Displays this broadband router’s model name (useful when

you need technical service)

Up Time

Displays the amount of time this router has been switched on

Hardware Version Displays this broadband router’s hardware version (useful

when you need technical service)

Boot Code

Displays this broadband router’s boot code version (useful

Version

when you need technical service)

Runtime Code Displays this broadband router’s runtime code version (useful

Version

when you need technical service)

Internet Connection

IP Address Mode
IP Address Subnet Mask Default Gateway
MAC Address Primary DNS Secondary DNS

Displays how this broadband router currently obtains IP addresses Displays the IP address of the WAN connection Displays the subnet mask of the WAN connection Displays the IP address of the WAN connection’s default gateway Displays the physical address of the WAN port Displays the IP address of the first DNS server Displays the IP address of the second (backup) DNS server

Wireless Configuration

Mode

Displays the operation mode of the wireless access point

ESSID

Displays the name of the access point

Channel Number Displays the channel number of the wireless network

13

y

Security

Displays the security authentication mode of the access point

LAN Connection

IP Address Subnet Mask DHCP Server MAC Address

Displays the IP address of the LAN connection Displays the subnet mask of the LAN connection Displays the status of the internal DHCP server Displays the physical address of the LAN port

The SSID, the up time, the IP address of the LAN connection, and the runtime code is always displayed on the top of the webpage.

If this router’s DHCP server function is enabled, please follow the following instructions to find this router’s IP address:
1. Click the “Start” button, then click “Run”.

14
y

2. Input “cmd”, and then click “OK”.
   3. Input “ipconfig”, then press “Enter”. Use the IP address following “Default Gateway” to access this router’s web-based configuration interface. Please note that the IP address you find may be different from this illustrated example.
   NOTE: If there is no IP address following “Default Gateway”, or if the address following “IP Address” begins with “169”, please try the following procedures: z Recheck the cable connection between the computer and the router. z Go to the beginning of this chapter and recheck every step of the setup
   procedure. z If both of the above fails, reset the broadband router. 2-4 Using “iQ Setup” This broadband router’s “iQ Setup” feature allows you to set up basic parameters in a few simple steps. 1. Click “Quick Setup” after logging in.
   15
   y

3. The following will appear.
   3. Click “Perform iQ Setup” and it will start detecting your Internet service type.
   Note: Your computer or iPhone can also use iQ Setup with a Wi-Fi connection. Please make sure you have connected to the correct Wi-Fi network. The router’s default SSID is “Edimax”.
   Dynamic IP If your Internet connection type is dynamic IP, you will see the following:
   16
   y

Note: For security reasons, Edimax suggests that you set up the wireless security. If you click “Yes (recommended)”, you will be asked to enter an SSID and a password (at least 8 digits).
Note: Please remember your password or you will not be able to use the Wi-Fi connection. PPPoE If your Internet connection type is PPPoE, you will see the following:
Please enter the username and password provided by your ISP (usernames and passwords are case-sensitive). Click “Next” and the following will appear:
17
y

Note: For security reasons, Edimax suggests that you set up the wireless security. If you click “Setup wireless security (recommended)”, you will be asked to enter an SSID and a password (at least 8 digits).
Note: Please remember your password or you will not be able to use the Wi-Fi connection. If your PPPoE connection is invalid, you will see the following:
Click “Try it again” and the wizard will try to connect to the Internet again with the current information. Clicking “Re-enter” will take you to the previous page and let you enter the username and password again. If your connection type is none of the above or if the auto-detection has failed, you will see the following page. Please select your connection type and enter the information accordingly.
18
y

19
y

CHAPTER III:

GENERAL SETUP

You can perform advanced configuration of this broadband router in “General Setup”.
1. Click “General Setup” after logging in.

2. All available setup items will appear under the “General Setup” tab.
3. Refer to the following list for further instructions:

z System z WAN z LAN z Wireless z Advance Settings z NAT z Firewall z Parental Control

(See section 3-1) (See section 3-2) (See section 3-3) (See section 3-4) (See section 3-5) (See section 3-6) (See section 3-7) (See section 3-8)

3-1 System

You can set up basic system settings under “System”.

20
y

You can configure your time zone, password, and remote management settings here. After you have completed the configurations, click “Apply” to save the changes.

3-1-1 Time Zone You can configure the time zone settings here.

Item Name Set Time Zone
Time Server Address
Daylight Saving

Description Please select the time zone of your country or region. If you cannot find your country/region, please select another country/region whose time zone is the same as yours. This router supports NTP (Network Time Protocol) for automatic time and date setup. Input the host name or IP address of the NTP server here. If you do not know the host name, please ask the network administrator or use “pool.ntp.org”. If your country/region uses daylight saving time, please check the “Enable Function” box, and select the start and end date.

Click “Apply” to save the changes. After you have clicked “Apply”, you will see the following message:
21

y

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-1-2 Password Settings
You can change the router’s default login password (“1234”) here. It is advised to do so to prevent others from logging in to your router without permission.

Item Name Current Password
New Password Confirm Password

Description Input the current password here. The default value is “1234”. Input your new password here. Input your new password again for confirmation.

Click “Apply” to save the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
22
y

3-1-3 Remote Management
Setting up the “Remote Management” function allows you to manage this broadband router from outside your local area network (from the Internet).

Item Name Host Address Port
Enabled

Description Assign an IP address with which to access this router remotely. Assign a port number with which to access this router remotely. The default value is “8080”. You can use any integer between 1 and 65534. Check this box to enable the “Remote Management” function.

Click “Apply” to save the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings. 3-2 WAN You can set up your Internet or WAN (Wide Area Network) connection under “WAN”.
23
y

Select a connection type and proceed with the setup; then click “Apply” to save the changes. If you are not sure which connection type you should use, please contact your Internet service provider for help.
3-2-1 Dynamic IP If your Internet service provider assigns IP addresses to you automatically through DHCP (Dynamic Host Configuration Protocol), select “Dynamic IP”.
24
y

Item Name Host Name MAC Address
DNS Address DNS Address 1 and 2 TTL

Description Input the host name of your computer here. This is optional and only required if your ISP asks you to do so. If your ISP only permits computers with certain MAC addresses to access the Internet, input your computer’s MAC address here. Press “Clone Mac address” to fill the MAC address field with your computer’s MAC address automatically. Select “Use the following IP address” if your ISP requires that you do so. Enter the primary and secondary DNS addresses assigned by your ISP here. Enable the “TTL” function if your ISP requires you to do so.

Click “Apply” to save the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-2-2 Static IP
If your ISP is providing you Internet access via a fixed IP address, select “Static IP”. Generally, your ISP will provide you with such information as IP address, subnet mask, gateway address, and DNS address.
25
y

Item Name Fixed IP Address Subnet Mask DNS Address 1 and 2 Default Gateway
TTL

Description Input the IP address assigned by your ISP here. Input the subnet mask assigned by your ISP here. Enter the primary and secondary DNS addresses assigned by your ISP here. Input the default gateway assigned by your ISP here. Some ISPs may call this “Default Route”. Enable the “TTL” function if your ISP requires you to do so.

NOTE: You must use the addresses provided by your ISP. Inputting incorrect values will cause malfunction.

Click “Apply” to save the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings. 3-2-3 PPPoE If your ISP is providing you Internet access via PPPoE (Point-to-Point Protocol over Ethernet), select “PPPoE”.
26
y

Item Name User Name Password MAC Address
DNS Address
DNS Address 1 and 2 TTL Service Name MTU
Connection Type

Description Input the user name assigned by your ISP here. Input the password assigned by your ISP here. If your ISP only permits computers with certain MAC addresses to access the Internet, input your computer’s MAC address here. Press “Clone Mac address” to fill the MAC address field with your computer’s MAC address automatically. Select “Use the following IP address” if your ISP requires that you do so. Enter the primary and secondary DNS addresses assigned by your ISP here. Enable the “TTL” function if your ISP requires you to do so. Give this Internet service a name (optional). Input the MTU value of your network connection here. If you do not know, use the default value. Please specify a connection type here. There are 3 options:

1. “Continuous” keeps the Internet connection alive all the time.
   2. “Connect on Demand” only connects to the Internet when you initiate Internet connection.
   3. “Manual” connects to the Internet only when the “Connect” button on this page is clicked, and disconnects when the “Disconnect” button is clicked.
   27

y

Idle Time Out
Enable Dual-WAN Access

Specify the amount of time the router waits before shutting down an idle connection. This option is only available when “Connect on Demand” is selected. Check the “Enable Dual-WAN Access” box if your ISP requires you to do so.

Click “Apply” to save the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-2-4 PPTP
Select “PPTP” if your ISP is providing you Internet access via PPTP (Point-to- Point Tunneling Protocol).
If your ISP is providing you dynamic IP addresses, select “Obtain an IP address automatically”. If your ISP is providing you a static IP address, select “Use the following IP address”.

28
y

Item Name Host Name MAC Address
IP Address Subnet Mask Default Gateway MAC Address
DNS Address DNS Address 1 and 2 Enable Dual-WAN Access

Description Input the host name of your computer here. This is optional and only required if your ISP asks you to do so. If your ISP only permits computers with certain MAC addresses to access the Internet, input your computer’s MAC address here. Press “Clone Mac address” to fill the MAC address field with your computer’s MAC address automatically. Input the IP address assigned by your ISP here. Input the subnet mask assigned by your ISP here. Input the default gateway assigned by your ISP here. Some ISPs may call this “Default Route”. If your ISP only permits computers with certain MAC addresses to access the Internet, input your computer’s MAC address here. Press “Clone Mac address” to fill the MAC address field with your computer’s MAC address automatically. Select “Use the following IP address” if your ISP requires that you do so. Enter the primary and secondary DNS addresses assigned by your ISP here. Check the “Enable Dual-WAN Access” box if your ISP requires you to do so.

NOTE: These settings must be configured according to your Internet service. Please contact your Internet service provider if you are not sure what to select.

Configure the “PPTP Settings” section.

29
y

Item Name User ID Password PPTP Gateway Connection ID MTU
BEZEQ-ISRAEL
Connection Type

Description Input the user name assigned by your ISP here. Input the password assigned by your ISP here. Input the PPTP gateway assigned by your ISP here. Give this connection a name (optional). Input the MTU value of your network connection here. If you do not know, use the default value. Check the “Enable” box if you are in Israel and using BEZEQ network services. Please specify a connection type here. There are 3 options:

Idle Time Out

1. “Continuous” keeps the Internet connection alive all the time.
   2. “Connect on Demand” only connects to the Internet when you initiate Internet connection.
   3. “Manual” connects to the Internet only when the “Connect” button on this page is clicked, and disconnects when the “Disconnect” button is clicked.
   Specify the amount of time the router waits before shutting down an idle connection. This option is only available when “Connect on Demand” is selected.

Click “Apply” to save the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-2-5 L2TP
Select “L2TP” if your ISP is providing you Internet access via L2TP (Layer-2 Tunneling Protocol).
If your ISP is providing you dynamic IP addresses, select “Obtain an IP address automatically”. If your ISP is providing you a static IP address, select “Use the following IP address”.
30
y

Item Name Host Name
MAC Address
IP Address Subnet Mask Default Gateway
DNS Address
DNS Address 1 and 2 Enable Dual-WAN Access

Description Input the host name of your computer here. This is optional and only required if your ISP asks you to do so. If your ISP only permits computers with certain MAC addresses to access the Internet, input your computer’s MAC address here. Press “Clone Mac address” to fill the MAC address field with your computer’s MAC address automatically. Input the IP address assigned by your ISP here. Input the subnet mask assigned by your ISP here. Input the default gateway assigned by your ISP here. Some ISPs may call this “Default Route”. Select “Use the following IP address” if your ISP requires that you do so. Enter the primary and secondary DNS addresses assigned by your ISP here. Check the “Enable Dual-WAN Access” box if your ISP requires you to do so.

NOTE: These settings must be configured according to your Internet service. Please contact your Internet service provider if you are not sure what to select.

Configure the “L2TP Settings” section.

31
y

Item Name User ID Password L2TP Gateway MTU
Connection Type

Description Input the user name assigned by your ISP here. Input the password assigned by your ISP here. Input the L2TP gateway assigned by your ISP here. Input the MTU value of your network connection here. If you do not know, use the default value. Please specify a connection type here. There are 3 options:

Idle Time Out

1. “Continuous” keeps the Internet connection alive all the time.
   2. “Connect on Demand” only connects to the Internet when you initiate Internet connection.
   3. “Manual” connects to the Internet only when the “Connect” button on this page is clicked, and disconnects when the “Disconnect” button is clicked.
   Specify the amount of time the router waits before shutting down an idle connection. This option is only available when “Connect on Demand” is selected.

Click “Apply” to save the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
32
y

3-2-6 WISP If your Internet service provider is providing you Internet service wirelessly, select “WISP”.

Item Name WISP ESSID Wireless Band Channel Number Site Survey
Security Settings

Description Enable or disable the WISP function. Input the name of your Internet service provider’s wireless access point here. Set the wireless frequency range in accordance with your Internet service provider’s requirements. Select the channel number that corresponds to that of your Internet service provider’s wireless access point. Click “Select Site Survey” and a pop-up window will appear. All reachable wireless access points will be shown in the window. Select a wireless access point from the list, and click “Done” to establish a connection. Clicking “Refresh” will renew the list. Configure the security settings in accordance to your Internet service provider’s requirements.

Click “Apply” to save the changes. After you have clicked “Apply”, you will see the following message:

33
y

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings. 3-3 LAN
You can configure your local area network under “LAN”.

Refer to the following list for further instructions:

z LAN IP

(See section 3-3-1)

z DHCP Server

(See section 3-3-2)

z Static DHCP Leases (See section 3-3-3)

3-3-1 LAN IP

You can assign the LAN interface’s IP address under “LAN IP”.

Item Name IP Address Subnet Mask 802.1d Spanning Tree
DHCP Server
Lease Time

Description Assign the LAN interface’s IP address here. Please input a subnet mask value for this network. If you wish to activate the 802.1d spanning tree function, select “Enabled”. If you wish to activate the DHCP server function, select “Enabled”. Select a lease time for the DHCP leases here. The DHCP client will be forced to obtain a new IP address after the period expires.
You can select “Forever” if you are using this
34
y

broadband router with less than 30 computers.
If you are not sure what to fill, here are some recommended values:
z IP Address: “192.168.1.254” z Subnet Mask: “255.255.255.0” z 802.1d Spanning Tree: “Disabled” z DHCP Server: “Enabled” z Lease Time: “Two Weeks” or “Forever”
3-3-2 DHCP Server
You can set the range of IP address leases under “DHCP Server”.

Item Name Start IP End IP Domain Name Default Gateway Address

Description Enter the start IP address for the DHCP server’s IP assignment. Enter the end IP address for the DHCP server’s IP assignment. You can input a domain name for your network (optional). You can assign a default gateway here (optional).

If you are not sure what to fill, here are some recommended values:
z Start IP: “192.168.1.1” z End IP: “192.168.1.200” z Domain Name: (blank) z Default Gateway Address: (blank)
3-3-3 Static DHCP Leases

You can set the router to assign a static IP address to specified computers/devices under “Static DHCP Leases”.

35

y

Item Name Enable Static DHCP Leases MAC Address IP Address
Add
Clear

Description Check this box to enable the function.
Input the specified computer’s MAC address here. Assign a fixed IP address for the specified computer here. After you have entered the MAC address and the IP address, click “Add” to add the information to the “Static DHCP Leases Table”. Click “Clear” to clear the MAC address and IP address fields.

All the assigned entries will be listed as follows:

Click “Apply” to save the changes. After you have clicked “Apply”, you will see the following message:
36
y

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings. 3-4 Wireless You can set up the 2.4GHz wireless LAN connection under “Wireless”.
3-4-1 Wireless Settings Basic 2.4GHz wireless settings can be configured here.
This router can operate in 6 different modes: z AP: Wireless access point z Station-Infrastructure: Acts as a wireless communication client and wired connection server z AP Bridge–Point to Point: Connects this router with another broadband router z AP Bridge–Point to Multi-Point: Connects this router with up to 4 other broadband routers
37
y

z AP Bridge–WDS: Connects this router with up to 4 WDS-capable broadband routers
z Universal Repeater: Repeats another wireless access point’s signal to extend its wireless signal coverage
3-4-1-1 AP Mode
The following settings will appear in “AP” mode:

Item Name Band
ESSID Channel Number

Description Select from one of the following options:
2.4GHz (B): Allows 802.11b wireless network clients to connect to this router.
2.4GHz (N): Allows 802.11n wireless network clients to connect to this router.
2.4GHz (B+G): Allows 802.11b and 802.11g wireless network clients to connect to this router.
2.4GHz (G): Allows 802.11g wireless network clients to connect to this router.
2.4GHz (B+G+N): Allows 802.11b, 802.11g, and 802.11n wireless clients to connect to this router (recommended). This is the name of your router. You can type any alphanumerical character here (maximum 32 characters). Select a channel from the dropdown menu. You can
38
y

Associated Clients Wireless Module

select the channel of your preference (1 to 13). Click “Show Active Clients” for the list of all connected wireless clients. Click “Refresh” in the new window to renew the list, and click “Close” to close the window.
Note: If you have a pop-up blocker installed, you may have to disable it, or set it to allow the pop-up window to show up. Select “Enable” to turn on the 2.4GHz wireless signal and select “Disable” to turn it off.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-4-1-2 Station-Infrastructure
In “Station-Infrastructure” mode, the router acts as a wireless communication client and provides wired communication for other wired devices. The following settings will appear in “Station-Infrastructure” mode:

39
y

Item Name Band

Description Select from one of the following options:

2.4GHz (B): Allows this router to connect to 802.11b wireless network servers (maximum transfer rate 11Mbps).

2.4GHz (N): Allows this router to connect to 802.11n wireless network servers (maximum transfer rate 150Mbps).

2.4GHz (B+G): Allows this router to connect to 802.11b and 802.11g wireless network servers (maximum transfer rate 11Mbps for 802.11b clients and 54Mbps for 802.11g clients).

2.4GHz (G): Allows this router to connect to 802.11g wireless network servers (maximum transfer rate 54Mbps).

ESSID Site Survey
Wireless Module

2.4GHz (B+G+N): Allows this router to connect to 802.11b, 802.11g, and 802.11n wireless servers (recommended). This is the name of your router. You can type any alphanumerical character here (maximum 32 characters). Click “Select Site Survey” and a pop-up window will appear. All reachable wireless access points will be shown in the window. Select a wireless access point from the list, and click “Done” to establish a connection. Clicking “Refresh” will renew the list. Select “Enable” to turn on the 2.4GHz wireless signal and select “Disable” to turn it off.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

40
y

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-4-1-3 AP Bridge–Point to Point
“AP Bridge–Point to Point” mode connects this router to another router and allows all the computers connected to the LAN ports of both routers to communicate with each other.
Please note that when you select this mode, this broadband router will act as a wireless bridge only. It will not accept other wireless clients. If you wish to use this function with a wireless access point that supports WDS, please select “AP Bridge–WDS” mode.

Item Name Band

Description Select from one of the following options:
2.4GHz (B): Allows 802.11b wireless network clients to connect to this router.
2.4GHz (N): Allows 802.11n wireless network clients to connect to this router.
2.4GHz (B+G): Allows 802.11b and 802.11g wireless network clients to connect to this router.
2.4GHz (G): Allows 802.11g wireless network clients
41
y

to connect to this router.

Channel Number MAC Address 1 Wireless Module

2.4GHz (B+G+N): Allows 802.11b, 802.11g, and 802.11n wireless clients to connect to this router (recommended). Select a channel from the dropdown menu. Both access points must use the same channel (1 to 13). Input the MAC address of the wireless access point with which you wish to connect. Select “Enable” to turn on the 2.4GHz wireless signal and select “Disable” to turn it off.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-4-1-4 AP Bridge–Point to Multi-Point
“AP Bridge–Point to Multi-Point” mode connects this router to up to 4 other routers and allows the computers connected to the LAN ports of every router to communicate with each other.
Please note that when you select this mode, this broadband router will act as a wireless bridge only. It will not accept other wireless clients. If you wish to use this function with a wireless access point that supports WDS, please select “AP Bridge–WDS” mode.

42
y

Item Name Band

Description Select from one of the following options:

2.4GHz (B): Allows 802.11b wireless network clients to connect to this router.

2.4GHz (N): Allows 802.11n wireless network clients to connect to this router.

2.4GHz (B+G): Allows 802.11b and 802.11g wireless network clients to connect to this router.

2.4GHz (G): Allows 802.11g wireless network clients to connect to this router.

Channel Number MAC Address 1 to 4 Wireless Module

2.4GHz (B+G+N): Allows 802.11b, 802.11g, and 802.11n wireless clients to connect to this router (recommended). Select a channel from the dropdown menu. All access points must use the same channel (1 to 13). Input the MAC addresses of the wireless access points with which you wish to connect. Select “Enable” to turn on the 2.4GHz wireless signal and select “Disable” to turn it off.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

43

y

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-4-1-5 AP Bridge–WDS
In “AP Bridge–WDS” mode, this broadband router acts as both a wireless communication bridge and a wireless access point. This router can connect to up to 4 WDS-compatible wireless access points and allows the computers connected every AP to communicate with each other.

Item Name Band

Description Select from one of the following options:
2.4GHz (B): Allows 802.11b wireless network clients to connect to this router.
2.4GHz (N): Allows 802.11n wireless network clients to connect to this router.
2.4GHz (B+G): Allows 802.11b and 802.11g wireless
44
y

network clients to connect to this router.

2.4GHz (G): Allows 802.11g wireless network clients to connect to this router.

ESSID Channel Number Associated Clients
MAC address 1 to 4 Wireless Module

2.4GHz (B+G+N): Allows 802.11b, 802.11g, and 802.11n wireless clients to connect to this router (recommended). This is the name of your router. You can type any alphanumerical character here (maximum 32 characters). Select a channel from the dropdown menu. All access points must use the same channel (1 to 13). Click “Show Active Clients” for the list of all connected wireless clients. Click “Refresh” in the new window to renew the list, and click “Close” to close the window.
Note: If you have a pop-up blocker installed, you may have to disable it, or set it to allow the pop-up window to show up. Input the MAC addresses of the wireless access points with which you wish to connect. Select “Enable” to turn on the 2.4GHz wireless signal and select “Disable” to turn it off.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-4-1-6 Universal Repeater
In “Universal Repeater” mode, this broadband router acts as a wireless signal repeater to extend the wireless coverage of the specified wireless access point.
45
y

Item Name Band
ESSID Channel Number Associated Clients

Description Select from one of the following options:
2.4GHz (B): Allows 802.11b wireless network clients to connect to this router.
2.4GHz (N): Allows 802.11n wireless network clients to connect to this router.
2.4GHz (B+G): Allows 802.11b and 802.11g wireless network clients to connect to this router.
2.4GHz (G): Allows 802.11g wireless network clients to connect to this router.
2.4GHz (B+G+N): Allows 802.11b, 802.11g, and 802.11n wireless clients to connect to this router (recommended). This is the name of your router. You can type any alphanumerical character here (maximum 32 characters). Select a channel from the dropdown menu. All access points must use the same channel (1 to 13). Click “Show Active Clients” for the list of all connected wireless clients. Click “Refresh” in the new window to renew the list, and click “Close” to
46
y

Root AP SSID Site Survey
Wireless Module

close the window.
Note: If you have a pop-up blocker installed, you may have to disable it, or set it to allow the pop-up window to show up. Input the SSID of the wireless access point with which you wish to connect. Click “Select Site Survey” and a pop-up window will appear. All reachable wireless access points will be shown in the window. Select a wireless access point from the list, and click “Done” to establish a connection. Clicking “Refresh” will renew the list. Select “Enable” to turn on the 2.4GHz wireless signal and select “Disable” to turn it off.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings. 3-4-2 Security Settings
Advanced security settings are available in certain modes to enhance connection security.

3-4-2-1 Disabled Connection encryption is disabled under this mode (not recommended).
47
y

3-4-2-2 WEP Selecting “WEP” enables WEP (Wired Equivalent Privacy) encryption.

Item Name Key Length Key Format
Encryption Key
Enable 802.1x Authentication RADIUS Server IP address RADIUS Server Port RADIUS Server Password

Description Two types of key lengths are available: 64-bit and 128-bit. Two types of key formats are available: ASCII and Hex. The number of characters your encryption key can use will be shown here. Input an encryption key here. In “ASCII” mode, you can use any alphanumerical character (0-9, a-z, and A-Z). In “Hex” mode, you can use 0-9, a-f, and A-F. Check this box to enable the 802.1x authentication function. You need a RADIUS server to perform 802.1x authentication. Input the RADIUS server’s IP address here. Input the RADIUS server port here. Generally, it is “1812”.
Input the password of the RADIUS server here.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

48
y

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-4-2-3 WPA Pre-Shared Key
WPA (Wi-Fi Protected Access) is a safer encryption mode than WEP (recommended).

Item Name WPA Unicast Cipher Suite Pre-Shared Key Format
Pre-shared Key

Description
Please select a WPA cipher suite supported by your wireless client. Available options are “WPA (TKIP)”, “WPA2 (AES)”, and “WPA2 Mixed”. Select a pre-shared key format here. “Passphrase” allows you to use 8 or more alphanumerical characters (up to 63). “Hex” allows you to use up to 64 characters within the ranges of 0-9, a-f, and A-F. Input the WPA key here.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-4-2-4 WPA RADIUS
If you have a RADIUS server on your local network, you can authenticate wireless clients via the RADIUS server’s user database.
49
y

Item Name WPA Unicast Cipher Suite
RADIUS Server IP address RADIUS Server Port RADIUS Server Password

Description Please select a WPA cipher suite supported by your wireless client. Available options are “WPA (TKIP)”, “WPA2 (AES)”, and “WPA2 Mixed”. Input the RADIUS server’s IP address here. Input the RADIUS server port here. Generally, it is “1812”. Input the password of the RADIUS server here.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings. 3-4-3 MAC Address Filtering
This function will help you prevent unauthorized users from connecting to your wireless router. Only those wireless devices whose MAC address matches the ones you have assigned here can gain access to your wireless router. Up to 20 MAC addresses can be assigned.
To enable MAC address filtering, check the “Enable Wireless Access Control” box.
50
y

Item Name MAC Address Comment
Add
Clear

Description Input the MAC address you wish to add here. You can input up to 16 alphanumerical characters describing the MAC address here (optional). Click “Add” to add the MAC address and associated comment to the MAC address list. Click “Clear” to remove everything in the MAC address and comment fields.

All MAC address entries will be listed in the following table:

To delete one or more entries, please check the box of the corresponding entry (under “Select”), and click “Delete Selected”. If you wish to delete all the entries, click “Delete All”.
Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
51
y

3-4-4 WPS (Wi-Fi Protected Setup) Settings
WPS (Wi-Fi Protected Setup) is a convenient way to establish a secure connection between this broadband router and WPS-compatible wireless clients.

Item Name Enable WPS WPS Status Self PIN Code SSID Authentication Mode
Passphrase Key Config Mode

Description Check this box to enable the WPS function. The status of the WPS configuration is displayed here. This router’s WPS PIN code is displayed here. This router’s SSID is displayed here. This router’s wireless security authentication mode is displayed here. The WPA passphrase key is displayed as asterisk here. Select this router’s WPS configuration role here.

Registrar: This broadband router will act as the WPS registrar and wait for the wireless client’s WPS configuration request.

Configure via Push-Button Configure via Client PIN

Enrollee: This broadband router will act as the WPS enrollee and send WPS configuration requests to other WPS registrars. Click “Start PBC” to start push-button WPS configuration. You can also use the “WPS/Reset” button located at the back of this router. Input the WPS-enabled wireless client’s PIN code and

52

y

Code

click “Start PIN” to establish a WPS connection.

3-5 Advanced Settings

You can configure such advanced networking functions like QoS, DDNS, port forwarding, and DMZ under “Advanced Settings”.

3-5-1 QoS Quality of Service (QoS) is a means for computers on the network to share Internet bandwidth with guaranteed bandwidth quality for each device. Without QoS, all devices on the network will compete for Internet bandwidth, so applications that require higher bandwidth (like video streaming and network telephone) will suffer from network latency issues.

Item Name Enable QoS Total Download Bandwidth
Total Upload Bandwidth
Rule Name
Bandwidth

Description Check this box to enable the QoS function. You can set a limit to the total download bandwidth here. To disable download bandwidth limitation, input “0” here. You can set a limit to the total upload bandwidth here. To disable upload bandwidth limitation, input “0” here. Input a name for this QoS rule for identification purposes. Set the speed limitation for this QoS rule here:

Local IP Address Local Port Range
Remote IP Address

1. Select the direction of data transfer for this rule 2. Input the maximum data rate for this QoS rule 3. Define the data rate value as “Guarantee”
   (guaranteed bandwidth) or “Max” (maximum bandwidth allowed) Set the IP address range that will be affected by this QoS rule. If only one IP address is involved, input the IP address in the left field only. Set the port range that will activate this QoS rule. If only one port is involved, input a single number here (1 to 65535). If multiple ports are involved, input the starting and ending port numbers in x-y format (e.g. 10-20). Set the remote IP address range that will be affected by this QoS rule. If only one remote IP address is
   54

y

Remote Port Range
Traffic Type
Protocol Add Reset Edit Delete Selected Delete All Move Up Move Down

involved, input the IP address in the left field only. Set the remote port range that will activate this QoS rule. If only one remote port is involved, input a single number here (1 to 65535). If multiple remote ports are involved, input the starting and ending port numbers in x-y format (e.g. 10-20). If you are creating a QoS rule for a specific type of traffic, you can define it here. You do not need to fill in any port range information (above) for this type of QoS rule. Define the protocol type here (TCP or UDP). Click the “add” button to add new QoS rules to the table. Click “Reset” to erase all the values you have just entered. Select a rule in the QoS table and click “Edit” to modify the contents of a specific rule. Only one rule can be edited at a time. Select the rule(s) you want to delete and click “Delete Selected” to perform the task. Click “Delete All” to delete all the rules listed in the QoS table. The “Move Up” button moves a selected rule up in the list, giving it a higher priority. The “Move Down” button moves a selected rule down in the list, giving it a lower priority.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings. 3-5-2 DDNS

DDNS (Dynamic DNS) is an IP-to-hostname mapping service for users who do not have a static (fixed) IP address and need to provide services to other users over the Internet.
This router supports the following DDNS service providers:
z DHS (http://www.dhs.org) z Dyn (http://dyn.com) z ODS (http://ods.org) z TZO (http://www.tzo.com) z GnuDIP (http://gnudip2.sourceforge.net) z DyNS (http://www.dyns.cx) z ZoneEdit (http://www.zoneedit.com) z DHIS (http://www.dhis.org) z CyberGate (http://cybergate.planex.co.jp/ddns)
Please go to one of the DDNS service provider’s website and get a DDNS account. After that, you can configure the DDNS settings here:

Item Name Dynamic DNS Provider Domain Name
Account/Email Password/Key

Description Enables or disables the DDNS function. Select your DDNS service provider here. Input the domain name you have obtained from the DDNS service provider. Input your DDNS account or email of registration. Input DDNS service password.

The following are the settings for a DHIS DDNS account:

Item Name HostID ISAddr Authentication Type
HostPass

Description Input the HostID provided by DHIS here. Input the ISAddr provided by DHIS here. Select the authentication type from the dropdown menu (password or QRC). Input the HostPass provided by DHIS here.

AuthP/AuthQ

(This field appears only when the authentication type is “Password”). Input the AuthP/AuthQ provided by DHIS here.

(This field appears only when the authentication type is “QRC”).

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-5-3 Port Forwarding
The port forwarding function allows you to redirect the ports of an Internet IP address to corresponding ports of an IP address in the local network. The port number(s) of the Internet IP address and the local IP address must be identical. If not, please use the virtual server function.
57
y

Item Name Enable Port Forwarding Private IP Computer Name
Type Port Range
Comment Add Reset

Description Check this box to enable the port forwarding function. Input the IP address of the computer in the local network that provides the Internet service. Computer names found in the local network are listed here. You can select a computer name and click the “<<” button to add the selected computer’s IP address to the “Private IP” field. Select the connection type (TCP or UDP) here. If you are not sure, please select “Both”. Input the starting port number in the left field and the ending port number in the right field. If only one port number is to be redirected, fill that port number in the left field. You can add an optional note in the “Comment” field. Up to 16 alphanumerical characters are supported. Click “Add” to add the settings to the port forwarding table. Click “Reset” to clear all the settings.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings. 3-5-4 DMZ

Adding a device with a private IP address to the DMZ (demilitarized zone) will map the device’s private IP to an Internet IP, so users will be able to access that device over the Internet.

Item Name Enable DMZ Public IP Address
Client PC IP Address Computer Name
Add Reset

Description Check this box to enable the DMZ function. If you select “Dynamic IP”, you need to designate a connection session from the dropdown menu. If you select “Static IP”, please input the Internet IP address to which you want to map the private IP address. Please input the private IP address of the device in the local network here. Computer names found in the local network are listed here. You can select a computer name and click the “<<” button to add the selected computer’s private IP address to the “Client PC IP Address” field. Click “Add” to add the settings to the DMZ table. Click “Reset” to clear the settings.

NOTE: Each public IP address can be mapped to one client PC IP address only.

All DMZ entries are displayed in “Current DMZ Table”:

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-6 NAT
This broadband router supports four types of NAT functions. See the following for instructions.
3-6-1 Virtual Server
This function allows you to redirect a port of an Internet IP address to a specified port of a private IP address, so you can set up an Internet service on the computer in the local network without exposing it to the Internet directly.

Item Name Enable Virtual Server Private IP Computer Name
Private Port Type

Description Check this box to enable the virtual server function. Please input the private IP address of the device in the local network here. Computer names found in the local network are listed here. You can select a computer name and click the “<<” button to add the selected computer’s private IP address to the “Private IP” field. Input the port number of the private IP address here. Select the connection type (TCP or UDP) here. If you

Public Port Comment
Add
Reset

are not sure, please select “Both”. Input the port number of the Internet IP address here. You can add an optional note in the “Comment” field. Up to 16 alphanumerical characters are supported. Click “Add” to add the settings to the virtual server table. Click “Reset” to clear all the settings.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-6-2 Special Applications
Some applications require multiple simultaneous connections, which cannot be set up with simple NAT rules. You can configure the “Special Applications” feature for such applications.

Item Name Enable Special Applications IP Address
Computer Name

Description Check this box to enable the special applications function. Input the IP address of the computer in the local network that provides the Internet service. Computer names found in the local network are listed

TCP Port to Open
UDP Port to Open
Comment Popular Applications
Add Reset

here. You can select a computer name and click the “<<” button to add the selected computer’s IP address to the “IP Address” field. Input the TCP port number(s) here. The port number can be a single value, or a range (e.g. “20-50”). If you need to input multiple, non-contiguous port numbers, separate each number with a comma (“,”). If the application does not use TCP ports, leave it blank. Input the UDP port number(s) here. The port number can be a single value, or a range (e.g. “20-50”). If you need to input multiple, non- contiguous port numbers, separate each number with a comma (“,”). If the application does not use UDP ports, leave it blank. You can add an optional note in the “Comment” field. Here is a list of port mapping settings for numerous network games. Select a game from the dropdown menu and click “Add” to add the settings to the respective fields. Click “Add” to add the settings to the table. Click “Reset” to clear all the settings.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings. 3-6-3 UPnP Settings The UPnP (Universal Plug and Play) feature allows other network devices to communicate with this broadband router.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:
Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings. 3-6-4 ALG Settings The ALG (application layer gateway) feature is a kind of network connectivity support for applications like network gaming and instant online chatting.
All ALG requiring applications that are compatible with this broadband router is listed here. Check the applications you will be using.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:
Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings. 3-6-5 Static Routing In most cases, all the computers in the local network will use a default gateway (generally provided by your ISP) to access the Internet. However, if you have a preferred network route, you can use this function to bypass the default gateway.

Item Name Enable Static Routing Destination LAN IP Subnet Mask
Default Gateway
Hop Count
Interface
Add Reset

Description Check this box to enable the function. Input the destination LAN IP here. Input the subnet mask of the destination network here. Input the gateway IP address that leads to the specified network. Input the hop count (the distance between the destination network and this broadband router) here. Select the interface that leads to the destination network (LAN or WAN). Click “Add” to add the settings to the table. Click “Reset” to clear all the settings.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:
Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings. 3-7 Firewall You can configure the firewall functions under “Firewall” to protect your network and computer. 3-7-1 Access Control You can allow or deny computers with certain MAC addresses access to the network.

Item Name Enable MAC Filtering
Client PC MAC Address Computer Name
Comment Add

Description Check this box to enable MAC address filtering, and select “Deny” or “Allow” to deny or allow network access to the computer(s) in the list. Please input the MAC address of a computer here. Dashes (“-“) and colons (“:”) are not required. Computer names found in the local network are listed here. You can select a computer name and click the “<<” button to add the selected computer’s MAC address to the “Client PC MAC Address” field. You can add an optional note in the “Comment” field. Up to 16 alphanumerical characters are supported. Click “Add” to add the settings to the table.

Reset

Click “Reset” to clear all the settings.

If you wish to set up IP address filtering, use the “IP Filtering Table” on this page:

Item Name Enable IP Filtering
Add PC

Description Check this box to enable IP address filtering, and select “Deny” or “Allow” to deny or allow network access to the IP address(es) in the list. Click “Add PC” to add an entry to the list.

Item Name Client PC Description Client PC IP Address
Client PC Service

Description Input a description for the IP address here. Up to 16 alphanumerical characters are supported. Input the starting IP address in the left field and the ending IP address in the right field. If only one IP address is to be redirected, fill that IP address in the left field. Select the Internet services that will apply to this access control rule.

If the service you wish to deny or allow is not listed, you can use the “User Defined Service” settings.

Item Name Protocol
Port Range

Description
Select the protocol type (TCP or UDP) here. If you are not sure, please select “Both”.
Input the port number(s) here. The port number can be a single value, or a range (e.g. “20-50”). If you need to input multiple, non-contiguous port numbers, separate each number with a comma (“,”).

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings. 3-7-2 URL Blocking Use the “URL Blocking” function to prevent computers in the local network from accessing certain websites.

Item Name Enable URL Blocking URL/Keyword
Add Reset

Description Check this box to enable the function. Input the URL of the website or the keyword contained in the URL here. Click “Add” to add the settings to the table. Click “Reset” to clear all the settings.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.
3-7-3 DoS
The denial-of-service attack (DoS attack) is a common attack that paralyzes your Internet connection. Configure the DoS function to prevent such attacks.

Item Name Ping of Death

Description Check this box to filter out malicious ping packets that causes computers to stop responding.

Discard Ping from WAN Port Scan Sync Flood Advanced Settings

Check this box to ignore all inbound ping requests when malicious intruders try to paralyze your Internet connection with many ping requests. Check this box to block attempts of a malicious intruder trying to scan for open ports on your Internet IP address. Check this box to filter out fake connection requests trying to drain the memory of your server. Click “Advanced Settings” to configure details of the DoS function.

Item Name Ping of Death
Discard Ping from WAN Port Scan Sync Flood

Description Set the threshold for this defense mechanism to be activated here. Check the “Ping of Death” box and input the frequency of the threshold. You can also input the burst value, which activates the mechanism when the number of ping of death packets exceeds the defined number in the specified duration of time. Check this box to ignore inbound ping requests when malicious intruders try to paralyze your Internet connection with many ping requests. Check the “Port Scan” box to block attempts of a malicious intruder trying to scan for open ports on your Internet IP address. Then check one or more port scanning methods that you would like to block. Set the threshold for this defense mechanism to be activated here. Check the “Sync Flood” box and input the frequency of the threshold. You can also input the burst value, which activates the mechanism when the number of connection requests exceeds the defined

number in the specified duration of time. Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:
Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings. 3-8 Parental Control You can control when your child is able to access the Internet under “Parental Control”.
To enable the parental control function, check “Enable Parental Control”. This router will only allow Internet access to other computers when your computer is present. By default, your computer’s MAC address will be listed here automatically. You can also input another computer’s MAC address manually in the “MAC Address of Parental PC” field.
NOTE: You do not need to enter the punctuation marks in the MAC address. Just enter the 12 hexadecimal numbers (as shown above). You also have the option of setting up a parental control schedule.

Item Name MAC
Weekdays Time Start/Time Stop Add Reset

Description Input the MAC address of the computer you want to control (i.e. your child’s computer) in the “MAC” field. You can also select a computer in the “Select” dropdown list, and copy it by clicking “<<“. Select the days that will be affected by the parental control rule. Select the starting/ending time the parental control rule will take effect. Click “Add” to add the parental control rule to the list. Click “Reset” to clear all fields.

To delete one or more entries in the list, please check the box of the corresponding entry (under “Select”), and click “Delete”. If you wish to delete all the entries, click “Delete All”.

Click “Apply” to save the changes, or click “Cancel” to discard the changes. After you have clicked “Apply”, you will see the following message:

Click “Apply” to save the changes and restart the broadband router. It takes about 60 seconds for the broadband router to restart. Click “Continue” to configure other settings.

4-1 Status

CHAPTER IV:

STATUS, TOOLS & LANGUAGE

You can check how your router is currently operating under “Status”.

1. Click the “Status” tab.
2. Basic system information will be shown under “System”. More information can be found in the other subpages under “System”.

4-1-1 Internet Connection This page shows the status of your Internet connection.

4-1-2 Device Status This page shows the current settings of your wired and wireless LAN.

4-1-3 System Log This page shows all logged system information. You can click “Save” to download the log file to your computer. You can also click “Clear” to remove all logs, or click “Refresh” to reload the logs.
4-1-4 Security Log This page shows all logged security-related information. You can click “Save” to download the log file to your computer. You can also click “Clear” to remove all logs, or click “Refresh” to reload the logs.

4-1-5 Active DHCP Client This page shows all current DHCP clients. You can click “Refresh” to reload the list.
4-1-6 Statistics This page shows the statistical information of each network interface and the total system up time.
4-2 Tools This broadband router comes with several tools that help you backup the settings, upgrade the firmware, and restart the device.

1. Click the “Tools” tab.
   2. You will be able to access the configuration tools, upgrade your firmware, or restart the router here.

4-2-1 Configuration Tools
You can backup and restore your system configurations here. You can also reset all settings to the factory default.
1. Click “Configuration Tools”.

Item Name Backup Settings
Restore Settings

Description Click the “Save…” button to save the current settings on your computer as a “config.bin” file. Click the “Browse…” button to select a previously saved “config.bin” file from your computer, then click “Upload” to replace the current settings with the settings in the “config.bin” file.

Restore to Factory Default

Click “Reset” to restore the settings to the factory default. A pop-up message window will appear and ask you to confirm the
reset.

2. Click “Apply” to save the changes. If you wish to go back to the previous page, click “Previous”.
   4-2-2 Firmware Upgrade

You can upgrade your firmware in the “Firmware Upgrade” section.

1. Download the firmware file from our company’s website and save it on your computer.

2. Click “Browse…” to find the firmware file saved on your computer, then click “Apply” to start firmware upload. The broadband router will restart after the file is uploaded. All your current settings will be lost after the firmware is upgraded. NOTE: It is recommended that you use a wired Ethernet connection and not a wireless connection to upload the firmware file. Do not switch the broadband router or computer off while performing firmware upgrade. This will cause the broadband router to malfunction.
   4-2-3 Restart If your broadband router is not functioning properly or responding slowly, restarting the broadband router may solve the problem.
   1. Select “Reset”.
   76
   y

3. Click the “Apply” button to restart the broadband router. 3. When you are prompted to confirm the restart, click “OK”. 4-3 Language This broadband router’s web-based user interface supports several languages. You can change the display language with the “Language” dropdown menu at the upper-right corner of the user interface.
   77
   y

References

• GnuDIP
• Dynamic Host Information Services
• DHS Front Page
• EDIMAX - Netwoking Solution Provider including SMB Wi-Fi Access Point, AP Controller, SMB and Industrial PoE++ L2+ Switch, Industrial Embedded Wirless (Wi-Fi, Bluetooth) USB Dongle (Adapter), Wi-Fi Smart Plug, IoT, Smart Home
• DNS Hosting, Dynamic DNS and Domain Management with Zoneedit – The Original DNS Provider
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>