GOLDEN LIGHTING 1094-SF Ariella 7 Wide Semi Flush Ceiling Fixture Instruction Manual
- June 17, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 1094-SF Ariella 7 Wide Semi Flush Ceiling Fixture
Product Specifications
- Model: 1094-SF
- Dimensions: 8′ x 30″
- Weight: 5.9 lbs
- Maximum Wattage: 36W
- Fixture Type: Pendants & Linear Pendants
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island:
Center a linear pendant over the island. If hanging pendants, use one
pendant for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Colgantes y colgantes lineales sobre una isla de cocina:
Centre un colgante lineal sobre la isla. Si cuelga colgantes, use un
colgante por cada 24″ de isla. Los accesorios deben colgar al menos 30″ por
encima de la encimera.
Pendants & Chandeliers Above a Dining Room Table:
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas:
The bottom should hang at least 7.5 feet from the floor. Allow
clearance for any opening doors.
FAQ:
How do I identify the fixture’s wires?
The fixture wires are labeled as follows:
- Hot
- Neutral
- Ground
Do I need to assemble the fixture?
No, this item arrives fully assembled and ready for installation.
How do I connect the wires?
Follow the instructions provided in the manual for connecting the fixture
wires to the house wires. Ensure proper matching of hot, neutral, and ground
wires.
How do I finish the installation?
- Lift the canopy up to the ceiling over the mounting strap until the mounting screws protrude from the holes in the canopy.
- Thread deco nuts onto the exposed threads of the mounting screws and tighten until the canopy is snug against the ceiling.
- Slide the glass over the cap and socket, and secure it in place by twisting the socket ring to the socket.
- Install a light bulb (not included) into the socket according to the fixture’s specifications.
- Turn on the power and test the fixture.
What is the maximum recommended wattage for the light bulb?
Refer to the fixture’s specifications for the maximum recommended wattage. Do
not exceed this limit.
Thank You for Choosing Us for Your Lighting Needs!
DIMENSION
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice
Assembly Instructions
How to Identify the Fixture’s Wires
- Hot: Smooth, Black, or Transparent with Black Inner Thread
- Neutral: Ribbed, White or Transparent with White Inner Thread
- Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement parts
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
- Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above.
- Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap. 1. From the parts bag remove the mounting strap (B) assembly.
- Mounting strap (B) contains several threaded holes. Find the pair of holes that matches the spacing of the holes on the junction box.
- Two sets of mounting screws (A & D) should be attached to mounting strap (B).
- You may need to tighten nuts (C) that hold these screws in place. If the screws are not attached, please hold canopy (F) up to mounting strap (B).
- Line up the holes in canopy (F) with the holes in mounting strap (B) and insert mounting screws (A) into mounting strap (B) so that mounting screws (A) protrude through the holes in canopy (F).
- Mounting screws (A) are long, so please test the canopy against the mounting strap to see how far you should insert the screws.
- Tighten nuts (C) onto mounting screws (A) to hold the screws in place. 2.
- Place mounting strap (B) over the junction box. Secure mounting strap (B) to the junction box using mounting screws (D) and a screwdriver. Tighten the screws securely.
- Pull house wires for the center of the mounting strap.
- Unscrew socket ring (K) and set aside for later use
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation. Please proceed to the next step.
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
4. Lift the canopy (F) up to the ceiling over mounting strap (B) until mountingscrews (A) protrude from the holes in the canopy (F). Thread deco nuts (G) onto exposed threads of mounting screws (A). Tighten until the canopy (F) is snug against the ceiling. 5. Carefully slide glass (I) over cap (J). Slide glass(I) and cap (J) over socket (H) and secure in place by twisting socket ring (K) to the socket (H). 6. Install a light bulb (not included) into socket (H) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is now complete. Turn on the power and test the fixture.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>