SW-MOTECH LVG.01.529.11000 Lever Protector Instruction Manual
- June 4, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH LVG.01.529.11000 Lever Protector
Lever Guard
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TOV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers· specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
PARTS LIST
MONTAGE/MOUNTING
NOTE: The Installation is shown for the left side. The installation on
the right side of the vehicle is analogous to the left side of the vehicle.
Remove the original handlebar end weights on both sides.
Then remove the inner handlebar weights with a pull hammer from the vehicle.
ATTENTION: We recommend having the inner handlebar weights movement by a specialist workshop!
Attach the parts (1I to (5] loosely together, as shown in the drawing.
ATTENTION: Use liquid thread locker!
Insert the clamp spacers of the lever guards on both sides up to the
collar in the open handlebar ends.
Now align the lever guards parallel to the ground.
Tighten the screws [41 so that the clamp spacers [21 and [31 are wedged in the
handlebar tubes. Tight en the screws [41 as specified
Insert the cover caps (6) on both sides into the openings of th e mounted lever guards (1).
MOUNTING INSTRUCTIONS
Wind protection for lever guard
Thank you for choosing this premium product from SW-MOTECH. Please visit
our webshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required (e.g. ABE
certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturers· specifications or
replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise
specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the
vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
Insert on both sid es the wind deflectors 111 to the lever guards.
Attach the wind deflectors 11 I to the lever guards.
ATTENTION: Use liquid thread locker, suitable for plastic (*: eg. Loctite
425)!
Carefully tighten the screws 12) as specified.
ATTENTION: Over-tightening the screws will damage the plastic parts!
Tel. I phone+ 49 (0)6425 / 8168 – 050
Fax / fax+ 49 (0)6425 / 8168 – 10
info@sw-motech.com
www.sw-motech.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>