kogan KAHTP22AUTA 2000W Smart Electric Panel Heater User Manual
- June 17, 2024
- Kogan
Table of Contents
kogan KAHTP22AUTA 2000W Smart Electric Panel Heater
BEFORE USE
Read and follow all the instructions in this manual even if you feel you are
familiar with the product, and find a place to keep it handy for future
reference. For your convenience record the complete model number (located on
the product identification plate) and the date you received the product.
Retain in the event that warranty service is required.
NOTE: The rating of this product (as marked on the product identification
plate) is based on specific loading tests. Normal use, or the use of other
recommended attachments, may draw significantly less power.
IMPORTANT SAFEGUARDS
When using any electrically powered product, basic safety precautions should
always be followed.
WARNING- to reduce the risk of fire, electrical shock or injury to
persons or property:
-
Read all instructions before using this appliance and keep them for future reference.
-
Use only the voltage specified on the rating plate of the heater.
-
Do not cover or restrict airflow to the inlet or exhaust grilles in any manner as the appliance may overheat and become a fire risk.
-
Do not cover grilles, block entry or exhaust of airflow by placing appliance against any surface. Keep all objects at least 1 meter from the front, side and rear of the appliance.
-
Do not place the appliance close to a radiant heat source.
-
Do not operate in areas where gasoline, paint or other flammable liquids are used or stored.
-
This appliance heats up when in use. To avoid burns, do not let bare skin touch hot surface. Switch off and let cooling before moving.
-
Do not use the appliance to dry clothes.
-
Do not insert or allow foreign object or metal utensils to enter any ventilation or exhaust opening, as this may cause an electric shock, fire or damage to the appliance.
-
Do not immerse in liquid or allow running into the interior of the appliance, as this could create an electrical shock hazard.
-
Do not reach for an appliance that has fallen into water. Switch of at supply and unplug immediately.
-
Do not operate any appliance with a damaged cord, plug or after the appliance malfunctions or has been dropped or damaged in any manner.
-
Return to the Kogan customer service team for examination, electrical or mechanical adjustment, service or repair.
-
Do not operate appliance with wet hands.
-
The most common cause of overheating is deposits of dust or fluff in the appliance. Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning air vents and grilles.
-
Do not use this appliance in a window as rain may cause electric shock.
-
Do not use a abrasive cleaning products on this appliance. Clean with a damp cloth (not wet) rinsed in hot soapy water only. Always remove plug from the mains supply before cleaning.
-
Do not connect the appliance to the mains voltage until completely assembled and adjusted.
-
This appliance is not intended for use in outdoor locations.
-
Do not use this appliance in the immediate surrounds of a bath, a shower or a swimming pool or other liquids.
-
Always operate upright.
-
Switch off and let cooling before moving.
-
Do not operate with cord set coiled up as a build-up of heat is likely, which could be sufficient to become a hazard.
-
The use of an extension cord with this appliance is not recommended.
-
Do not remove plug from power socket until the appliance has been switched off.
-
Do not remove plug from power socket by pulling the supply cord-always grip plug.
-
Always unplug appliance when not in use.
-
CAUTION: This product is NOT suitable to be used on long pile carpets or Flokati rugs.
-
Do not allow cord to come in contact with heated surface during operation.
-
Do not run cord under carpeting, throw rugs or runners etc. Arrange cord away from traffic areas so that it will not be tripped over.
-
Do not twist, kink or wrap the cord around the appliance, as this may cause the insulation to weaken and split. Always ensure that all cord has been removed from any cord storage area.
-
Do not use outdoors or whilst standing on a damp floor.
-
Do not store appliance while it is still hot.This appliance is not intended for use by young children or infirm persons without supervision.
-
Young children should be supervised to ensure they do not play with the appliance.
-
The appliance must not be located immediately below a socket-outlet.
-
Do not use this appliance with another programmer, timer or any other device that switches the heater on automatically, since a fire risk exists if the appliance is covered or positioned incorrectly.
-
All covers of this appliance is intended to prevent direct access to the heating elements and must be in place when the appliance is in use.
-
“WARNING: In order to avoid overloading, do not cover the heater.”
-
To reduce the risk of electric shock, do not immerse or expose the product or flexible cord to rain, moisture or any liquid other than those necessary for correct operation of the product.
-
The fire-guard does not give full protection for young children and for infirm persons.
-
If the supply cord is damaged, it must be replaced by a qualified electrical persons in order to avoid a hazard.
-
Do not use this appliance outdoors, or on wet surfaces. Avoid spilling liquid on the appliance.
“CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such a timer, or connected to a circuit that is regularly on and off by the utility.” -
Use this appliance only as described in this manual. Any other use is not recommended by the manufacturer and may cause fire, electric shock or injury.
-
This appliance is intended for household use only and not for commercial or industrial use.
Overview of the appliance
Specifications
- Rated Power: 2000W/1000W
- Rated Voltage: 240V 50Hz
- Dimensions (mm): 83075400
Guide to the control panel
- Power On/Off button
- Mechanical/automatic mode choose
- Mechanical/automatic mode timer setting.
- Confirm button
- Downwards adjustment
- Upwards adjustment
- High/low power selected
- Power indicator light
- Day
- Heating element working indicator light
- Low power
- High power
- Negative ion indicator – (This model has no negative ion function)
- Mechanical control
- Automatic control
- Timer
- Hours display
- Minutes display
- Real time temperature display
- Temperature unit display ( )
Operation Guide
Power on/off
Plug in the unit and you will hear a short buzz, then the red power indicator
“8” will always light up. The LCD display will light up for 12 seconds then
turn off. Press “1” (Power) to turn on the device with a short buzz. The day,
time, room temperature and temperature unit will be displayed. One of the
power settings (“HI” or “”LO”) and the model (“M” or “A”) will be on. The
setting temperature is factory set at 24 . The memory is ℃ held in the event
of power interruption.Temperature setting (mechanical mode is the same as the
automatic mode): temperature units are measured in . ℃
When the device is power on, press “5” or “6” and the temperature will flash, then press “6” or “5” again to set the desired temperature. The highest setting temperature is 30 and the lowest temperature is 5 . Press ℃ ℃ “4” to finish temperature setting, or the system will return to operation state without operation in 5S. When the newly set temperature stops flashing the room temperature will show on the LCD screen.
Time setting
When using the device for the first time, the time on screen may not be the
same as the actual time, so please adjust the right date and time (mechanical
model and automatic mode would be the same).
Day
When the device power is on, press the “3” and “4” at the same time for 3
seconds, the day “9” will flash. Press the “5” or “6” to choose the right day
and press “3” to finish. ”9” will stop flashing.
Hour
After setting the right day, the hour “17” will flash. Press “6” or “5” to set
the right hour and press “3” to finish. “17” will stop flashing.
Minute
After setting the right hour, the minute “18” will flash. Press “6” or “5” to
set the right minute and press “3” to finish. “18” will stop flashing.
Second
After setting the right minute, the second “19” will flash. Press “6” or “5”
to set the right second and press “3” to finish. “19” will stop flashing.
After setting the right second, press button “3” again or “4” to finish time
setting. All time symbols will stop flashing.
Automatic “A” mode timer setting (7 days timer)
When in automatic mode, the “16” will not display.
Day setting
Press “2” to choose automatic mode. The LCD will display “A”, then press “3”
and the current day on the screen “9” will flash. Press the “5” or “6” to set
the day which need to set the timer, the “17” and “18” will
display the timer for last setting. Press “3” to finish day setting, at which
point ”9” will stop flashing.
Timer setting
“19” display – The first number is 1 this means the heater is on the first
running time and so on. “17” and “18” will display the last setting time, and
the “17” will flash. Press the “6” or “5” to set the desired time, then press
“3” to finish the first turn on running time (E.g. 07 hour). Then the “18”
will begin to flash, so press “6” or “5” to adjust the time, then press “3” to
finish the first turn off running time (E.g. 11 hour). This example will set
the first running time between the hours of 7 – 11.
Then the “19” display displays 2, showing you are now on the second running time and you can repeat your settings for this time frame and so on. Then press “4”to finish the timer setting. Please notice that the setting program will only save after you press the “4” button. Factory pre-setting running time is 07-11；and 13-18；closed time ≥ opened time.
To set the running time in one week
There are two ways to set the running time in one week: After you have set the
first day, you can press “4” for 3 seconds to copy and save the data to the
following days, or after you have set the first day and confirm, you can press
“4” for 3 seconds (within 12 seconds) to copy the data to the following days.
Please notice that the data could only copy for the following days, (eg, when
you are setting the Wednesday running time and press “4” for 3 seconds, the
Thursday to Sunday would be in the same running time, but Monday and Tuesday
could not copy the data.)
After you have set the first day, it can go onto the following day setting, you can set the different running time according to method .After setting the running program: Press “4” to save and the heater will operate in accordance to those on and off times. If not currently within the running time, the device will turn off after 10 seconds.
Mechanical “M” mode timer setting (the timer just for the current day)
Press “2” select the mechanical mode and the LCD will display “M”. Press “3”
to set the timer, “17” will flash, press :’6” or “5” to adjust the hour, then
press “3” again to set the minute. Press “4” to confirm the timer and “16”
will light up. If you press “3” when setting the minute that means this will
cancel the timer setting. When the setting time is less than the current time,
the timer will not work.
Turn off
Press “1” in mechanical mode. If you press “1” in automatic mode, the unit
will not turn off. Please press“M/A” to change to the mechanical mode to turn
off if needed.
Negative ion function
This model has no negative ion function, but the “ION” “13” will display on
the screen when you press “7” for 3 seconds.
High /low power select
Press “7” to choose high/low power. When high power is chosen, “12” will light
up, while “11” will be off. When you choose low power, “11” will light up,
while “12” will be off.
Mechanical mode and automatic mode select
Press “2” could select the mechanical or automatic mode. When mechanical mode is selected M will display and A when in automatic mode.
The memory function after shutting down by hand
Whatever is on, after being turned off, or turned off for timing over, the
setting program is the one set last.
The memory function after shutting down suddenly
Whatever power applied after no electric or improperly shut-down, the device
will start to work automatically on the last setting. The timer would be the
rest time from shut-down.
Press sounds
There is a buzzer sound with both valid key presses and continuous key
pressing.
Electronic locking
When the device power is on, pressing buttons “+” and “-” at the same time for
3 seconds will lock all function controls, which will be displayed on “19” as
a square for 5 seconds, and then change to real temperature display. If any
button is pressed, the display will show the square for 5 seconds with no buzz
sound, then change to the real temperature display.
Methods to unlock
- Cut off the electric supply to the device
- Press “+”and “-” at the same time for 3 seconds,
Safety feature
The unit is equipped with a high temperature limit switch, and the heater will
automatically shut off if it is in an over-heating condition. The heater will
automatically come back on when it has cooled down.
User tips
CLEANING INSTRUCTIONS: Always ensure the heater is clean behind. Press down the two top catches “P” (please refer to the diagram below) on the back of the heater to pull the heater forwards. After cleaning the heater you must return to the fixed in the normal position. The heater requires regular cleaning to ensure trouble free operation:
- Unplug the heater from the mains supply before cleaning.
- Ensure that the heater has been allowed to cool down completely before cleaning.
- Use a damp cloth (not wet) to wipe the exterior of the heater to remove dust and dirt.
- Use a vacuum cleaner to remove dust and fluff from around the grilles.
- Ensure the heater is dry before plugging back into the mains supply.
Warning
- The heater must be fixed correctly onto the wall or put the heater in the correct position.
- The heater is to be installed so that the controls cannot be touched by a person using a bath or shower.
- The heater is to be installed so that it is not located directly under a power socket outlet.
- When the heater is working as it is in free standing mode with the foot set, please do not use it in the vicinity of bath, shower, or swimming pool.
- When the heater is working as it is in wall mounted mode, do not touch the control unit when using it in the vicinity of bath, shower or swimming pool.
- Consult a qualified electrician or service technician if the power cord is damaged.
- DO NOT cover the heater when it is working.
- Always store the heater when not in use.
- Make sure the heater has cooled down before store it away.
Service
When you require service, contact the Kogan customer service team.
Storage
If you do not plan to use the heater for extended periods of time, it is
recommended that the heater is cleaned and then stored (preferably in its
original packaging) in a cool dry place.
WALL MOUNTING GUIDE
Documents / Resources
|
kogan KAHTP22AUTA 2000W Smart Electric Panel
Heater
[pdf] User Manual
KAHTP22AUTA 2000W Smart Electric Panel Heater, KAHTP22AUTA, 2000W Smart
Electric Panel Heater, Smart Electric Panel Heater, Electric Panel Heater,
Panel Heater, Heater
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>