LandWare E-115 Pocket PC User Guide

LandWare E-115 Pocket PC

Product Information

Specifications

• Software Copyright : 2000-2003
• Hardware Design : PATENT PENDING
• Trademarks: GoType!, GoType! Pro
• Manufacturer: LandWare, Inc.

Warranty Information
This product is covered by a warranty. Please refer to the warranty documentation provided with your purchase for more details.

• Care and Maintenance
  In case of liquid spillage on the keyboard, immediately disconnect the connected organizer from the keyboard and tilt it to let the liquid drain out. Allow the keyboard to dry for 24 hours at room temperature. Keyboard protectors are available separately from LandWare.

• Contacting LandWare
  If you require technical assistance or have any questions concerning this product, please contact us via:

  • Telephone: 201-261-7944
  • Fax: 201-261-7949
  • Email: help@landware.com
  • Website: www.landware.com
  • Mail: LandWare, Inc., PO Box 25, Oradell, NJ 07649 USA

• Communications Regulation Information
  FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with FCC rules. Please refer to the instructions if interference to radio or television reception is suspected. Unauthorized changes or modifications to this product could void the FCC Certification and negate your authority to operate the product.

• DOC STATEMENT
  DOC Class B Compliance: This digital apparatus complies with the Class B limits for radio noise emissions from digital apparatus as set out in the interference-casing equipment standard entitled Digital Apparatus, ICES-003 of the Department of Communications.

Product Usage Instructions

Getting Started
To get started with your GoType! keyboard, please follow the eight simple steps below:

1. Install the GoType! software
2. Activate the GoType! software
3. Connect the organizer to the keyboard
4. Adjust keyboard settings (if necessary)
5. Use the keyboard for data input
6. Disconnect the organizer from the keyboard
7. Clean and maintain the keyboard
8. Provide feedback to LandWare

Step 1: Install the GoType! Software
To install the GoType! software, follow these steps:

1. Ensure that your handheld’s sync software and cradle (or cable) are available.
2. Place your organizer in the cradle provided with your Pocket PC and establish a connection with the ActiveSync software.
3. Insert your GoType! disk into your computer.
4. Click the Start button, select Run, and type “a:setup” (without quotes).
5. Follow the on-screen prompts to complete the software installation.

Step 2: Activate the GoType! Software
Before using the keyboard, you need to activate the GoType! software:

1. Ensure that your organizer is turned off.
2. Dock your organizer with the keyboard.

Step 3: Connect the Organizer to the Keyboard
To connect your organizer to the GoType! keyboard, follow these steps:

1. Ensure that the GoType! software is activated.
2. Place your organizer in the keyboard’s cradle or connect it using the provided cable.

Step 4: Adjust Keyboard Settings (if necessary)
If you need to adjust the keyboard settings, please refer to the manual that came with your connection software for detailed instructions.

Step 5: Use the Keyboard for Data Input
You can now use the GoType! keyboard to input data into your connected organizer. Enjoy the convenience of a physical keyboard for faster and more comfortable typing.

Step 6: Disconnect the Organizer from the Keyboard
To disconnect your organizer from the GoType! keyboard, simply remove it from the cradle or disconnect the cable.

Step 7: Clean and Maintain the Keyboard
To clean and maintain your GoType! keyboard, follow these guidelines:

• In case of liquid spillage, refer to the care and maintenance instructions provided earlier in this manual.
• Regularly clean the keyboard surface using a soft cloth and mild cleaning solution.
• Avoid using abrasive materials or harsh chemicals that may damage the keyboard.
• Consider using a keyboard protector, available separately from LandWare, to prevent dust and debris accumulation.

Step 8: Provide Feedback to LandWare
We value your feedback and are committed to improving this product. If you have any suggestions, comments, or concerns, please contact us using the provided contact information.

FAQ (Frequently Asked Questions)

1. Q: What should I do if liquid spills on the keyboard?
   A: Immediately disconnect the connected organizer from the keyboard, tilt it to let the liquid drain out, and let the keyboard dry for 24 hours at room temperature. Keyboard protectors are available separately from LandWare.

2. Q: How can I contact LandWare for technical assistance or product-related questions?
   A: You can contact LandWare via telephone, fax, email, website, or mail using the provided contact information.

3. Q: Can I make changes or modifications to the product?
   A: Unauthorized changes or modifications to the product could void the FCC Certification and negate your authority to operate the product.

warranty information

• LandWare, Inc. warrants this product against defects in materials and workmanship for a period of ONE (1) YEAR from the date of original retail purchase. If you discover a defect and notify LandWare of the same during the warranty period, LandWare will, at its option, repair, replace, or refund the purchase price of the product to you at no charge. THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLU-SIVE. LANDWARE DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. LAND-WARE IS NOT RESPONSIBLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM ANY BREACH OF WARRANTY OR UNDER ANY OTHER LEGAL THEORY. Because some jurisdictions do not permit the exclusion or limitations set forth above, they may not apply in all cases.
• copyright information
• The GoType! software is copyright 2000-2003 with all rights reserved by LandWare, Inc. The GoType! hardware design is PATENT PENDING by Sicon/Parallel Design. LandWare, GoType!, GoType! Pro are registered trademarks of LandWare, Inc. The slogan “Innovation for the Mobile Age” is a trademark of LandWare, Inc.

care and maintenance

• Keep your keyboard away from extreme heat.
• Don’t leave your keyboard anyplace that is extremely dusty, damp or wet.
• Take care not to spill any liquid on your keyboard. If you do, turn off your connected organizer immediately. Remove the connected organizer from the keyboard and tilt it to let the liquid drain out. Let the keyboard dry for 24 hours at room temperature. Keyboard protectors are available separately from LandWare.

contacting LandWare

We thank you for purchasing GoType! and are confident that you will soon find it to be an indispensable addition to your connected organizer. We are committed to continually improving this product for you and welcome your feedback. If you require technical assistance or have any questions concerning this product please contact us via:

• Telephone (201)  261-7944, fax 201-261-7949
• email www.landware.com/help
• Web http://www.landware.com
• Mail LandWare, Inc.
• PO Box 25
• Oradell, NJ 07649 USA

Communications Regulation Information

FCC statement

This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in Part 1 of FCC rules. See instructions if interference
to radio or television reception is suspected

Radio and television interference
The equipment described in this manual generates, uses and can radiate radio- frequency energy. If it is not installed and used properly-that is, in strict accordance with LandWare’s instructions it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in Part 15 of FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. You can determine
whether your computer system is causing interference by turning it off.

• If the interference stops, it was probably caused by the computer or one of the peripheral devices. If your computer system does cause interference to radio or television reception, try to correct the interference by using one or more of the following measures:
  • Turn the television or radio antenna until the interference stops.
  • Move the Keyboard to one side or the other of the television or radio.
  •  Move the Keyboard farther away from the television or radio

If necessary, consult a LandWare authorized service provider or LandWare Inc. See the service and support information that came with your LandWare product. Or, consult an experienced radio/television technician for additional suggestions. You may find the following booklet helpful: Interference Handbook (stock number 004-000-00493-1). This booklet, prepared by the Federal Communications Commission, is available from the U.S. Government Printing Office, Washington, DC 20402.

• Important

  • Changes or modifications to this product not authorized by LandWare could void the FCC Certification and negate your authority to operate the product. This product was tested for FCC compliance
    under conditions that included the use of Casio Cassiopeia’s.

• DOC STATEMENT

  • DOC Class B Compliance
  • This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-casing equipment standard entitled “Digital Apparatus”, ICES-003 of the Department of Communications

To get the most out of your new purchase we recommend you read this document fully

getting started

Follow the eight simple steps below

1. install the gotype! software

   • Your handheld’s sync software and cradle (or cable) are required for the installation of this software. The GoType! Software must be installed and activated before the key-board can be used.

   • NOTE: While the keyboard may be used as a cradle, we recommend that you first install the GoType! software via the cradle that came with your Pocket PC device.

   • To install the GoType! Pro driver follow the steps below. For more detailed information refer to the manual that came with your connection software.
     Installation instructions

   • Place your organizer in the cradle your received with  your Pocket PC and establish a connection with the ActiveSync software.

   • Insert your GoType! disk.

   • Click the Start button, select Run, and type: a:setup.

   • Follow the on-screen prompts to complete the software installation.

2. activate the gotype! software
   The GoType! Pro driver software must be initially activated before the keyboard can be used. IMPORTANT NOTE: The GoType! Pro driver will only function correctly if the organizer is turned off BEFORE it has been docked with the keyboard.
   To activate the GoType! driver

3. Tap the Start or Windows button on the organizer.

4. Tap GoType!, to launch the GoType! driver settings  application.

5. Tap the ON radio button.

6. The GoType! driver will now enable and disable itself automatically.
   Note: the radio buttons will not change state, but the driver will only activate if the keyboard is dectected.

7. turn the organizer off
   This is an extremely important step. The organizer must be turned off BEFORE it is docked with the keyboard. Only then will the GoType! Pro keyboard function correctly.

8. extend the keyboard stabilizer
   A special foot at the rear of the keyboard may be extracted to provide maximum stability when typing. It is recommended that you extract this foot prior to using your key-board.

9. set port switch to keyboard mode
   To enable communication between the keyboard and the organizer the GoType! port switch must be moved over to the right hand side (abc).
   NOTE: You will not be able to type on the keyboard while in serial mode ( ).

10. dock the organizer in the keyboard
    Place the organizer into GoType!’s integrated dock. Remember, the organizer must be turned off during this stage.

11. turn the organizer on
    Press the Power button on the handheld to activate the Pocket PC by pressing its power switch. If the GoType! driver has been correctly installed and activated (see step 2) it will automatically enable keyboard input.

12. launch an application
    You are now ready to type with your keyboard. Simply open any program that accepts text input and start typing. It’s that easy.
    Example: Creation of a text memo
    Tap F5 to create a new memo and start typing. Text should appear on the screen.

performing an activesync

The GoType! keyboard comes equipped with an integrated serial port or USB port (depending on your model) that can be used to connect the keyboard to a desktop computer. On handhelds that supports ActiveSync, this port enables you to perform an ActiveSync directly from the keyboard.

1. connect the serial/USB cable
   Plug one end of the GoType! serial or USB cable into the port on the left side of the keyboard. Remove your existing cradle. Plug the other end into the same port on your PC.
   NOTE: On a Cassiopeia E-125, you will need to change the default PC Connection setting from USB to SERIAL in order to connect with the GoType!keyboard.
   To change this setting on your E-125:
   Tap Start, tap Settings, tap Connections, tap PC, select 57600 Default from the pop-up, and tap OK.

2. set port switch to ActiveSync mode
   To perform an ActiveSync through the keyboard

3. TURN THE ORGANIZER OFF

4. Move the port switch to the left (arrows)

5. Turn the organizer ON, ActiveSync should now begin.
   To use the keyboard after an ActiveSync
   TURN THE ORGANIZER OFF

6. Move the port switch to the keyboard abc mode

7. Turn the organizer ON You should now be able to use the keyboard.

recharging the organizer

plug in the AC adapter
GoType! Pro can provide recharging power for your Pocket PC unit while they are sitting in the keyboard.
NOTE: The GoType! power port supports the original adapter that came with your Pocket PC ONLY. Under no circumstances should any other adapter be used.

altering operational settings
The GoType! driver provides a number of options that allow you to customize its operation to best suit the way you work.
Altering operational preferences

1. Tap the Start or Windows button on your Pocket PC.
2. Tap Programs > GoType!
3. The window shown on the left will appear.

enabling and disabling gotype! During the normal course of operations you should not have to manually enable and disable the GoType! driver. The soft- ware is smart enough to activate and deactivate itself automatically when the organizer is placed in or removed from the keyboard. In order for it to achieve this:

1. The organizer must be turned off before it is docked with the keyboard.
2. The organizer must be turned off before it is removed from the keyboard.
   If for some reason you need to manually disable the driver, simply tap the Off radio button within the GoType! soft-ware.

• altering keyboard behavior
  • Setting delay and key repeat rates
  • Tap and drag the Delay until repeat to change how long you need to hold a key down until it starts to repeat. Moving the slider to the Off position will disable this feature completely. Tap and drag the Key repeat rate slider to change how fast a key repeats when you hold it down.
• configuring the function keys
  • The six function keys along the top of the keyboard can be set to launch your favorite applications. With the addition of the Shift and Alt modifier keys you can easily launch up to 18 different programs.

To define/edit a function key

1. Launch the GoType! application from the Start menu.
2. Tap the Function Keys tab.
3. Specify the modifier key by tapping either the on-screen Shift, Alt or Normal buttons.
4. Choose from the pop-up menus which program should be assigned to each Function key.
5. Tap OK.

The following applications are launched by default:

special command key combinations
The GoType! keyboard also includes the following special keys / key combinations:

troubleshooting

commonly asked questions
type but nothing appears.
Did you install the GoType software driver? If yes, these are the steps to enable your GoType! Pro:

1. Remove the organizer from the keyboard.
2. Make sure that your GoType! driver is ON.
3. Turn off the organizer.
4. Dock the organizer in the keyboard.
5. Ensure the serial switch is set to keyboard (abc) mode.
6. Turn your organizer ON.
7. Tap one of the GoType!’s function keys.

• When I attach my modem to my Organizer it does not appear to work correctly now that I have the GoType! software installed.
• Before using a modem you should first disable the GoType! Pro driver. To do so, open the GoType! program on your connected organizer and tap OFF.
• How do I scroll/select an appointment time from within my datebook/calendar application
• This needs to be accomplished with your stylus. After you have selected a time, you can use GoType! Pro to enter your desired text.
• Can I move between fields in my address book?
• It depends on the operating system you are running. In the Windows CE 2.1 for Palm-sized PC’s the operating system supports the Tab key to move field to field. For Pocket PC devices, the use of the Tab key is not supported.
• How do I launch an application with GoType!?
• The six function keys along the top of the keyboard can be set to launch your favorite applications. See the previous section on “Configuring the function keys” for more detail.

functional limitations

Considerable effort has been made to ensure the GoType! Pro keyboard works seamlessly with all Pocket PC applications. However because some applications were designed without a keyboard in mind there are still instances where the stylus is still required.

References

• LandWare - products for the mobile age
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>