behringer 173 Quad Gate/Multiples Legendary Analog Quad Gate and Multiples Module for Eurorack User Guide
- June 6, 2024
- Behringer
Table of Contents
Behringer 173 Quad Gate/Multiples Legendary Analog Quad Gate and
Multiples Module for Eurorack
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any
person who relies either wholly on or in part upon any description,
photograph, or statement contained herein. Technical specifications,
appearances, and other information are subject to change without notice. All
trademarks are the property of their respective owners. Midas, Klark Teknik,
Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer,
Bugera, Aston Microphones, and Coolaudio are trademarks or registered
trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd.
2021 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online
at community.musictribe.com/pages/support#warranty.
173 QUAD GATE/MULTIPLES Controls
Controls
- GATE OUT – Send the gate signal to another module via a 3.5 mm TS cable.
- GATE IN – Connect an incoming signal via a 3.5 mm TS cable.
- GATE CV – Connect a control voltage signal from other modules to control gate operation, non-inverting (active high), and inverting (active low) inputs.
- MULTIPLES – Connect a signal to the A jack that will be sent to multiple designations via the B, C, and D jacks in the same row.
Power Connection
The module comes with the required power cable for connecting to a standard Eurorack power supply system. Follow these steps to connect power to the module. It is easier to make these connections before the module has been mounted into a rack case.
- Turn the power supply or rack case power off and disconnect the power cable.
- Insert the 16-pin connector on the power cable into the socket on the power supply or rack case. The connector has a tab that will align with the gap in the socket, so it cannot be inserted incorrectly. If the power supply does not have a keyed socket, be sure to orient pin 1 (-12 V) with the red stripe on the cable.
- Insert the 10-pin connector into the socket on the back of the module. The connector has a tab that will align with the socket for correct orientation.
- After both ends of the power cable have been securely attached, you may mount the module in a case and turn on the power supply.
Installation
The necessary screws are included with the module for mounting in a Eurorack
case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of fixed holes spaced 2 HP
apart along the length of the case, or a track that allows individual threaded
plates to slide along the length of the case. The free-moving threaded plates
allow precise positioning of the module, but each plate should be positioned
in the approximate relation to the mounting holes in your module before
attaching the screws.
Hold the module against the Eurorack rails so that each of the mounting holes
are aligned with a threaded rail or threaded plate. Attach the screws part way
to start, which will allow small adjustments to the positioning while you get
them all aligned. After the final position has been established, tighten the
screws down.
Signal Input
Type| 3.5 mm jack, DC coupled
Impedance| 160 kΩ, unbalanced
Maximum input level| +17 dBu
Signal Output
Type| 3.5 mm jack, DC coupled
Impedance| 1 kΩ, unbalanced
Maximum output level| +17 dBu
Frequency response| DC to 20 kHz
Output noise| < -90 dBu, 22 Hz – 22 kHz
Gate Control
Type
| 2 x 3.5 mm jacks, non-inverting and inverting
Impedance| > 50 kΩ, unbalanced
Switching threshold| Non inverting > +3 V, inverting < +1.5 V
Maximum input level| 10 V p-p
Multiples
Type| 24 x 3.5 mm TS mono jacks, unbalanced
Arrangement| 6 sets of 4 parallel jacks, passive
Compatibility| CV and audio signals
Power|
Power supply| Eurorack
Current draw| 40 mA (+12 V),
40 mA (-12 V)
Physical|
Dimensions| 28 x 81 x 129 mm
(1.1 x 3.2 x 5.1″)
Rack units| 16 HP
Weight| 0.18 kg (0.4 lbs)
Hereby, Music Tribe declares that this product is in compliance with Directive
2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/ EU, Directive
2012/19/EU, Regulation 519/2012 REACH SVHC and Directive
1907/2006/EC. Full text of EU DoC is available at
https://[community.musictribe.com](http://community.musictribe.com)/ EU
Representative: Music Tribe Brands DK A/S
Address: Gammel Strand 44, DK-1202 København K, Denmark UK
Representative: Music Tribe Brands UK Ltd.
Address: 6 Lloyds Avenue, Unit 4CL London EC3N 3AX, United Kingdom
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>