kogan KABLT21BNDA Compact Bullet Blender Mixer System User Guide

kogan KABLT21BNDA Compact Bullet Blender Mixer System

Product Information

Specifications

• Blender beaker
• Lid for blender beaker
• Cap for blender lid
• Base unit
• Pusher for juicer
• Juicer
• Large preparation beaker
• Storage lids(2)
• Blade unit with a fine blade
• Blade unit with a coarse blade
• Steam/shaker lid with large holes
• Steam/shaker lid with small holes
• Small preparation beaker
• Serving beakers with handle(4)
• Coloured rings(4)

Product Usage Instructions

Before First Use

1. Check that all components are included.
2. Read all safety instructions.
3. Wash and dry any parts that will come into contact with food before using the Compact Bullet Blender/Mixer System for the first time or after prolonged storage without use.
4. Place the base unit on a flat surface, such as a kitchen counter, and ensure that it is standing firmly.

Using the Compact Bullet Blender/Mixer System

Using the Preparation Beakers and Serving Beakers

1. Place ingredients in the large or small preparation beaker or one of the serving beakers.
2. Screw one of the blade units onto the beaker.
3. Place the beaker on the drive shaft on the base unit, aligning the pins on the beaker with the depressions in the base unit.
4. Hold the base unit down with one hand and press down on the beaker with the other hand. The motor runs as long as you press the beaker down. You can also get the motor to run continuously by pressing the beaker down and turning it slightly in a clockwise direction.

Using the Blender Beaker

1. Screw the blade unit with the coarse blade onto the blender beaker.
2. Place the food in the blender beaker.
3. Place the lid (2) on the blender beaker and turn it in a clockwise direction until it clicks into place.
4. Place the cap (3) in the hole in the blender beaker lid, aligning the pins on the cap with the holes in the lid. Turn the cap slightly in a clockwise direction until it clicks into place.
5. Place the blender beaker on the drive shaft on the motor unit, aligning the pins on the beaker with the depressions in the base unit.
6. Start the mixer as described above.
7. If you want to add more ingredients as you go along, you can remove the cap from the lid by turning it anticlockwise and lifting it. Stop the mixer before removing the cap to avoid splashes.
8. If you need to scrape inside or empty the blender beaker, wait until the blade has stopped completely before you remove the lid! Never use your fingers to scrape.

Important Safety Information

Never leave the Compact Bullet Blender/Mixer System unattended while in use. You may risk personal injury, fire, or shock if you use attachments, cups, or parts other than those supplied with your Compact Bullet Blender/Mixer System. Never keep the blade running for longer than a minute. Do not use the party mugs in the microwave.

Never leave the mixer running for more than 1 minute at a time, as the motor can overheat. If the preparation process requires longer than this, take a short break before starting the mixer again. You should also stop the mixer at regular intervals to check whether the items have been processed sufficiently. If the motor overheats and stops running, unplug the mixer and allow it to cool down for several hours before using it again.

FAQ

• Q: Can I use cups or parts that are not supplied with the Compact Bullet Blender/Mixer System?
• A: No, using attachments, cups, or parts other than those supplied with your Compact Bullet Blender/Mixer System may risk personal injury, fire, or shock.
• Q: Can I use the party mugs in the microwave?
• A: No, do not use the party mugs in the microwave.

INTRODUCTIONS

For Your Safety Please Read Before Operation

• Read all instructions before operating the Compact Bullet Blender/Mixer System.
• The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• If the supply cord is damaged, it must be done by a technician arranged by the Kogan customer service team. If the unit is out of warranty, then a licensed electrician must be used to prevent shock or fire.
• Do not immerse the cord, plug or base in water or other liquids.
• Do not pull, twist or mistreat the power cord.
• Avoid contact with moving parts.
• To avoid serious injury and product damage keep hands and utensils away from the moving blades.
• Always unplug the base when cleaning or assembling.
• Always use your Compact Bullet Blender/Mixer System on a flat, dry, clean, hard surface.
• Always completely assemble the blade and cup before placing on the motor base.
• Never microwave with the blade still attached. Remove the blade and twist on the perforated top.
• When microwaving, beware of steam and use oven mitts to remove hot cups.
• Do not allow the electrical cord to touch hot surfaces or hand over the sides of counters.
• Unplug the Compact Bullet Blender/Mixer System when not in use or cleaning.
• Never leave the Compact Bullet Blender/Mixer System unattended while in use.
• You may risk personal injury, fire or shock if you use attachments, cups or parts other than those supplied with your Compact Bullet Blender/Mixer System.
• Never keep the blade running for longer than a minute.
• Do not use the party mugs in the microwave.

PARTS

1. Blender beaker
2. Lid for blender beaker
3. Cap for blender lid
4. Base unit
5. Pusher for juicer
6. Juicer
7. Large preparation beaker
8. Storage lids(2)
9. Blade unit with a fine blade
10. Blade unit with a coarse blade
11. Steam/shaker lid with large holes
12. Steam/shaker lid with small holes
13. Small preparation beaker
14. Serving beakers with handles (4)
15. Coloured rings(4)

BEFORE FIRST USE

• Please check that all components are included.
• Please read all safety instructions.
• Before using the Compact Bullet Blender/Mixer System for the first time, or after prolonged storage without use, wash and dry any parts that will come into contact with food.
• Place the base unit on a flat surface, e.g. a kitchen counter, and make sure it is standing firmly.

Using The Compact Bullet Blender/Mixer System

Mixer Parts. The base unit(4) contains a motor. You can fit different accessories onto the drive shaft of the base unit, depending on the type of food you want to prepare. The two blade units (9 and 10) are used to chop, grate, blend, mix, grind and whisk food in either the blender beaker (1), the preparation beakers (7 and 13) or the serving beakers (14). The serving beakers are ideal for preparing and serving drinks, and the practical coloured rings (15) make it more comfortable to drink from them and easy for guests to tell them apart. The preparation beakers can also be used to cook or reheat food in a microwave oven or to store leftovers in the fridge. Three storage lids (8) and two steam/shaker lids (11 and 12) are provided for this purpose. The steam/shaker lids can also be used to sprinkle grated cheese or chopped herbs over your food. The juicer (6) is for extracting juice from fresh fruit in and clockwise direction until the pins lock into place under the black edge of the base unit. Stop the motor by turning the beaker slightly in an anticlockwise direction to release the pins.
See also ’Preparation techniques’ below.

Using the preparation beakers and serving beakers

• Place ingredients in the large or small preparation beaker or in one of the serving beakers.
• Screw one of the blade units onto the beaker.
• Place the beaker on the drive shaft on the base unit, so the pins on the beaker are lined up with the depressions in the base unit.
• Hold the base unit down with one hand and press down on the beaker with the other hand.
• The motor runs as long as you press the beaker down. You can also get the motor to run continuously by pressing the beaker down and turning it slightly in a clockwise direction

Using the Blender Beaker

• Screw the blade unit with the coarse blade onto the blender beaker.
• Place the food in the blender beaker.
• Place the lid (2) on the blender beaker, and turn it in a clockwise direction unit it clicks into place.
• Place the cap (3) in the hole in the blender beaker lid, so the pins on the cap fit into the holes in the lid. Turn the cap slightly in a clockwise direction until it clicks into place.
• Place the blender beaker on the drive shaft on the motor unit, so the pins on the beaker are lined up with the depressions in the base unit.
• Start the mixer as described above.

If you want to add more ingredients as you go along, you can remove the cap from the lid by turning it anticlockwise and lifting it up. Stop the mixer before removing the cap to avoid splashes.
If you need to scrape inside or empty the blender beaker, wait until the blade has stopped completely before you remove the lid! Never use your fingers to scrape.

Using the juicer

• Screw the blade unit with the coarse blade onto the blender beaker.
• Place the juicer into the blender beaker so that the four guide notches in the grey rim at the bottom of the juicer are lined up with the ribs on the inside of the blender beaker.
• Place the lid on the blender beaker. Please note that the lid can turn in two ways: with the open hole against the pouring spout or with the grill opening against the pouring spout. Ensure that you lock the lid into place by turning it slightly in a clockwise direction, as the lid has to hold the juicer in position inside the beaker.
• Place the blender beaker onto the base unit.
• Cut the fruit and vegetables that are to be squeezed into small pieces so they can fit through the hole in the lid.
• Press the blender beaker down and the motor will begin to run.
• To make the motor run continuously, turn the beaker slightly in a clockwise direction until it locks into place.
• Drop pieces of fruit and vegetables down through the hole in the lid, and press them down using the pusher (5).
• The squeezed juice collects in the bottom of the blender beaker.
• Remove the entire blender beaker from the base unit and pour the juice into a glass without taking the juicer out. This keeps the flesh of the fruit separate from the juice.

Important! Never leave the mixer running for more than 1 minute at a time, as the motor can overheat. If the preparation process requires longer than this, take a short break before starting the mixer again.
You should also stop the mixer at regular intervals to check whether the items have been processed sufficiently.
If the motor overheats and stops running, unplug the mixer and allow it to cool down for several hours before using it again.

Important! If the blade gets stuck while the motor is running continuously, unplug the mixer immediately to prevent damage to the motor.
Remove the beaker fitted with the blade unit from the base unit, and shake the ingredients in the beaker thoroughly. If the blade is still stuck, unscrew the blade unit from the beaker and carefully turn the blade around using your fingers.

Be careful – the blade is extremely sharp!
Once you are sure the blade can go around, fit the blade unit into the beaker, place the beaker onto the base unit and try again.

Preparation Techniques

Pulse technique- If you want the food to be chopped or blended coarsely, then instead of holding the beaker down, press it down briefly and intermittently several times with short breaks between. Take care not to lock the beaker into position, or the motor will run continuously.
Shaking technique- If the blade is not distributing the food properly in a beaker, you can lock the beaker into position so the motor is running continuously, lift the entire mixer from the counter and shake it back and forth a few times so the food shifts position in the beaker. Then put the mixer back on the counter and let it run a little longer.
Be very careful when you use the shaking technique! Hold both the beaker and base unit firmly to prevent them from separating from each other while you are shaking them.
Shake and pulse technique- If you want the food to be chopped or blended coarsely, you can lift the entire mixer from the counter and give it a powerful shake downwards, concluding the movement by briefly pressing the beaker down (pulse function). This sends the food down onto the blades. Continue until the food shows the desired consistency. Be very careful when using the shake and pulse technique! Hold both the beaker and base unit firmly to prevent them from separating from each other while you are shaking them.
Tapping technique- If the food sticks to the inside of the beaker and is unable to reach the blade, you can take the beaker with the blade unit fitted off the base unit and tap it gently against the kitchen counter so that the food falls onto the blade. Then return the beaker to the base unit and continue to process the food.
Important! Do not use any techniques other than the pulse technique when the blender beaker is fitted.

Important! If the blade gets stuck while the motor is running continuously, unplug the mixer immediately to prevent damage to the motor. Remove the beaker fitted with the blade unit from the base unit, and shake the ingredients in the beaker thoroughly. If the blade is still stuck, unscrew the blade unit from the beaker and carefully turn the blade around using your fingers.
Be careful – the blade is extremely sharp!
Once you are sure the blade can go around, fit the blade unit into the beaker, place the beaker onto the base unit and try again.
Important! If the mixer is to be used to prepare different types of food (e.g. raw meat followed by vegetables, or egg followed by fruit), you must wash the parts that come into contact with food between each type of food.

Selecting the right blade

The coarse blade is suitable for

• chopping e.g. onions, garlic and carrots
• chopping and mixing ingredients for dips and salsa
• blending ice cream, ice cubes, fruit and other ingredients for drinks, smoothies and milkshakes
• mixing batter for pancakes, mixes for muffins, etc.
• grating hard and soft cheese and chocolate

The fine blade is suitable for

• Pureeing hummus, soups, baby food, etc. chopping and grinding hard items such as coffee, crushing ice cubes, for fruit sorbets etc., beans, nuts, cinnamon sticks and dried fruit
• whipping cream
• mixing herb butter and sandwich spreads using cream cheese

Cooking in a microwave oven

• The two preparation beakers are suitable for use in a microwave oven. Once you have chopped or blended the food in the beaker, just unscrew the blade unit and put it on one of the steam lids. Then the beaker can be placed in the microwave.
• Be careful when removing the beaker from the microwave after cooking, as the contents can become extremely hot and steam is released when you remove the steam lid. For larger portions, it may be necessary to mix in the ingredients as you go along.

Important! The blade units must not be used in a microwave oven, as the metal parts can cause damage to the oven. The serving beakers and airtight storage lids must not be used in a microwave oven.
Storage
Ensure that the mixer is clean and dry before storing.

Cleaning

• Before cleaning, remove the plug from the wall socket.
• The best way to clean the exterior of the mixer base unit is with a slightly dampened cloth and, if necessary, a little detergent.
• The base unit must not be immersed in any form of liquid.
• If the blade unit is not screwed on properly, liquid may seep out into the internal part of the base unit. This may also be removed using a slightly dampened cloth and a little detergent. Check that the base unit is thoroughly dry inside before you use the mixer again after cleaning.
• The blender beaker, serving beakers, preparation beakers and all other loose parts can be washed up as usual and are dishwasher-safe.
• Inside the blade unit is a plastic sealing ring, which may become loose when the unit is put through a dishwasher. Therefore, please check that the sealing ring is still in place when you remove the blade unit from the dishwasher.
• Be careful if you wash the blade units by hand, as they are extremely sharp.
• Do not use any kind of strong or abrasive cleaning agent on the mixer or accessories. Never use a scouring sponge or similar to clean the mixer, as the surface may be damaged.

ENVIRONMENTAL TIPS

• Once any electrical product is no longer functional or required, it should be disposed of in such a way as to cause minimum environmental impact, under the regulations of your local authority.
• In most cases, you can take such products to your local recycling station.

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>