HYPERGEAR HBT08 Bluetooth Headphone User Manual

HYPERGEAR HBT08 Bluetooth Headphone

Specifications

previous track
4. LED Indicator| Shows the status of the headphones (charging, pairing, etc.)
5. USB-C Charging Port| Port for charging the headphones with a USB-C cable
6. Auxiliary Input| Input for connecting to audio sources with a 3.5mm auxiliary cable
7. Microphone| Built-in microphone for phone calls and voice commands

Note: If your device prompts for a PIN code, enter “0000”. The headphones will automatically reconnect to the last paired Bluetooth audio device when the unit is turned on.

Play via AUX

Use a 3.5mm auxiliary cable to connect the headphones to other audio sources including non-Bluetooth devices. Your music will automatically play.

Note: When wired via AUX, the headphones power off to save battery, and Bluetooth functions are automatically disabled. Use the controls on your source device instead.

Functions

• Volume Up/Next Track: Press & Hold / Press 1x
• Volume Down/Previous Track: Press & Hold / Press 1x
• Multifunction (MFB):
  • Power On: Press & Hold (2 sec)
  • Power Off: Press & Hold (4 sec)
  • Play/Pause: Press 1x
  • Answer/End Call: Press 1x
  • Reject Call: Press & Hold (2 sec)
  • Redial Call: Press 2x
  • Activate Voice Assistant: Press & Hold (3 sec)

Remote functions may vary depending on the phone model.

Important Safety Information

Read all safety instructions and warnings before using this product. Improper use and failure to follow safety guidelines could result in damage, excess heat, toxic fumes, fire, explosion, electrical shock, or other hazards causing serious and/or fatal injury and/or property damage and not the manufacturer’s responsibility. The user is responsible for maintaining this product with care for maximum use.

1. Do not store the device in a depleted state. Charge your unit at least once every 3 months even when not in use.
2. Permanent hearing loss may occur if you listen at high volumes. Set the volume to a safe level.
3. Do not store at extreme temperatures (below 40°F or above 90°F).
4. Recharge your device with the included USB-C cable or a certified 3rd party cable and a 2A charging adapter.
5. Do not attempt to modify, disassemble, or repair this product.
6. Avoid excessive drops, bumps, and abrasions. If the device has dents, punctures, tears, deformities, or corrosion, discontinue use and contact the manufacturer or dispose of it in an appropriate method.
7. If you find this product rapidly increasing in temperature, emitting an odour, deformed, abraded, or demonstrating an abnormal phenomenon, discontinue use immediately.
8. Disposal of the unit in the garbage is unlawful under state and federal environmental laws and regulations.

Limited One-Year Warranty: Contact info@myhypergear.com to submit a warranty claim. Proof of purchase is required.

FAQ

• How do I charge the HyperGear Pulse Wireless Headphones?
• Connect the headphones to a USB power source using the included USB-C charging cable. The LED indicator will turn red when charging and turn off when fully charged (approximately 1.5 hours).
• How do I pair the headphones with my device?
• Power on the headphones to enter pairing mode, indicated by a flashing blue and red LED. Use your device’s Bluetooth menu to find and select “HyperGear PULSE” for pairing. Enter “0000” if prompted for a PIN.
• Can I use the headphones with non-Bluetooth devices?
• Yes, use a 3.5mm auxiliary cable to connect the headphones directly to the audio source. Note that Bluetooth functions will be disabled in this mode.
• What should I do if the headphones are not functioning properly?
• Refer to the safety instructions for troubleshooting tips or contact HyperGear customer support at info@myhypergear.com.

Need help? Visit www.myhypergear.com for additional product information or email info@myhypergear.com.

OVERVIEW

1. Volume Up/Next Track
2. Play/Pause
3. Volume Down/Previous Track
4. LED Indicator
5. USB-C Charging Port
6. Auxiliary Input
7. Microphone

INSTRUCTIONS

Fully charge your headphones before first use
HOW TO CHARGE
Connect to a USB power source using the included USB-C charging cable

• Charging
• Fully Charged (approximately 1.5 hours)

HOW TO PAIR

When you power your headphones on the LED will flash BLUE and RED to indicate pairing mode.

1. Using the Bluetooth menu on your device (phone, tablet, etc.), enable searching for nearby Bluetooth devices

2. Select “HyperGear PULSE” to connect and pair.
   NOTE: If your device prompts for a PIN code, enter “0000”

3. Once paired, the LED will flash BLUE and you will hear a tone confirming the successful connection.

NOTE: The headphones will automatically reconnect to the last paired Bluetooth audio device when the unit is turned on.

PLAY VIA AUX
Use a 3.5mm auxiliary cable to connect the headphones to other audio sources including non-Bluetooth devices. Your music will automatically play.
NOTE: When wired via AUX, the headphones power off to save battery and Bluetooth functions are automatically disabled. Use the controls on your source device instead.

FUNCTIONS

Multifunction (MFB)

• Power On: Press & Hold (2 sec)
• Power Off: Press & Hold (4 sec)
• Play/Pause: Press 1x
• Answer/End Call: Press 1x
• Reject Call: Press & Hold (2 sec)
• Redial Call: Press 2x

Remote functions may vary depending on the phone model.

IMPORTANT

Read all safety instructions and warnings before using this product. Improper use and failure to follow safety guidelines could result in damage, excess heat, toxic fumes, fire, explosion, electrical shock or other hazards causing serious and/or fatal injury and/or property damage and not the manufacturer’s responsibility. The user is responsible for maintaining this product with care for maximum use.

1. Do not store the device in a depleted state. Battery cells may be damaged. Charge your unit at least once every 3 months even when not in use.
2. Permanent hearing loss may occur if you listen at high volumes. Set the volume to a safe level.
3. Do not store at extreme temperatures (below 40°F or above 90°F).
4. Recharge your device with the included USB-C charging cable or a certified 3rd party cable and a 2A charging adapter. Standard cables and adapters may charge the battery too slowly and damage/ overheat the battery or cause a fire hazard.
5. Do not attempt to modify, disassemble, or repair this product.
6. Avoid excessive drops, bumps, and abrasions. If the device has dents, punctures, tears, deformities, or corrosion, discontinue use and contact the manufacturer or dispose of in an appropriate method.
7. If you find this product rapidly increasing in temperature, emitting an odour, deformed, abraded, or demonstrating an abnormal phenomenon, discontinue use immediately.
8. Disposal of the unit in the garbage is unlawful under state and federal environmental laws and regulations.

CONTACT

• Contact info@myhypergear.com to submit a warranty claim.
• Proof of purchase is required.
• www.myhypergear.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>