LOREX Aurora Series 4K IP Wired Bullet Security Camera User Guide

: June 16, 2024
: Lorex

Table of Contents

Safety Precautions
Dislcaimers
What’s Included
Camera Placement Tips
Camera Mounting
Camera Connection
Weather-resistant Cap
Need Help?
Register Your Produc
Documents / Resources

Aurora Series
Lorex A14
E842CA, E842CAB, E842CD, E842CDB
Quick Start Guide

Safety Precautions

Follow all instructions for safe use and handling of the product.
Use the camera within given temperature, humidity and voltage levels noted in the camera specifications.
Do not disassemble the camera.
Do not point the camera directly at the sun or a source of intense light.
Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, chemical-based cleaners.
The supplied cable is rated for surface mounting only (Non-UL). Cables for in-wall and floor-to-floor installations are sold separately (CMR type). These and other cables are available at lorex.com.
It is recommended to connect the camera to the NVR or an external PoE switch. If using a power adapter with this camera, a REGULATED power supply is REQUIRED (not included). Use of a non-regulated, non-conforming power supply can damage this product and voids the warranty.

Dislcaimers

Use the camera only with compatible Lorex recorders. For a full list, visit lorex.com/compatibility.
Not intended for submersion in water. Installation in a sheltered location recommended.
This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night viewing modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the camera filter is working.
Audio recording and/or face recording without consent is illegal in certain jurisdictions. Lorex Corporation assumes no liability for use of its products that does not conform with local laws.

What’s Included

Note: Based on 1 camera
Bullet / E842CA, E842CAB
4K Ultra HD Bullet Camera Ethernet Extension Cable Mounting Template Anchors & Screws (4×) Dome / E842CD, E842CDB
4K Ultra HD Dome Camera
Ethernet Extension Cable
Mounting Template Mounting Bracket
Anchors & Screws (4×)

Camera Placement Tips

Take into consideration what you want to monitor and where is the best coverage area.
Place your camera close to the area of interest.
Point the camera where there is the least amount of obstructions (i.e. tree branches).
Install the camera in a location that is difficult for thieves and vandals to reach.
The best position is 10 ft (3 m) above ground, angled 15° down.
Secure cabling so that it is not exposed or easily cut.

Camera Mounting

Test your camera prior to selecting a permanent mounting location, see page 9.

Bullet / E842CA, E842CAB

Use the provided Mounting Template to mark holes for screws, then drill holes for the mounting screws.
Optional: Insert the provided drywall anchors if you are installing the camera in drywall.
Feed the cable through the mounting surface or cable notch and mount the camera’s bracket to the surface using the provided screws.
Connect cables as shown on page 12.
Loosen the adjustment screw and position your camera as needed, then tighten to secure it in place.
Remove the vinyl film from the camera lens when your installation is complete.

Dome / E842CD, E842CDB

Use the included Mounting Template to mark hole for screws, then drill holes for the mounting screws.
Optional: Insert the provided drywall anchors if you are installing the camera in drywall.
Using a Phillips-head screwdriver and the provided screws, secure the Mounting Bracket to the surface.
Feed the cable through the mounting surface or cable notch and mount the camera’s bracket to the surface using the provided screws.
Connect cables as shown on page 12.
Press the camera into the Mounting Bracket until you hear a ‘click’.
Loosen the adjustment screw and position your camera as needed, then tighten to secure it in place.
Remove the vinyl film from the camera lens when your installation is complete.

Camera Connection

Connect your camera directly to your recorder using the camera’s Ethernet extension cable.

Weather-resistant Cap

Twist the Ethernet extension cable’s pre-attached weather-resistant cap securely onto your camera’s Ethernet connector. If exposed to regular precipitation, seal the cap with silicone and electrical tape.

Need Help?

For related support, scan the QR code or visit:

|
---|---
help.lorex.com/E842CA| help.lorex.com/E842CD

Register Your Produc

Please see our full Terms of Service and Limited Hardware Warranty Policy at: lorex.com/warranty
Copyright © 2023 Lorex Technology Inc.
As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved.

lorex.com
help.lorex.com
E842_QSG_EN-FR-ES_R3

Documents / Resources

| LOREX Aurora Series 4K IP Wired Bullet Security Camera [pdf] User Guide
A14 E842CA, E842CAB, E842CD, E842CDB, Aurora Series 4K IP Wired Bullet Security Camera, Aurora Series, 4K IP Wired Bullet Security Camera, Wired Bullet Security Camera, Bullet Security Camera, Security Camera, Camera
---|---