SCHLAGE BE365 Keypad Deadbolt Instruction Manual

SCHLAGE BE365 Keypad Deadbolt

Product Information

Specifications

• Model: BE365, BE365F, BE365F20
• Installation: Keypad Deadbolt
• Door Thickness: 1 3/8 – 1 3/4 (35 mm) – (44 mm)
• Backset: 2 3/8 or 2 3/4 (60 mm or 70 mm)

Product Usage Instructions

Installation

1. Check door preparation.
2. Install the bolt, adjusting it as necessary.
3. Rotate the baseplate cam to the correct position, ensuring itB is vertical.
4. Connect the wire and insert a 9V battery. The lock will beep when the battery is connected.
5. Install the keypad.
6. Route the wire through the hole in the baseplate and install the baseplate.
7. If applicable, install the strike by drilling a hole at least 1 1/4 (32 mm) deep.
8. Install the cover, ensuring that the wires are not pinched.

Change Faceplate

1. Remove the faceplate.
2. Remove the backplate.
3. Install the drive-in faceplate.

Test Lock
To lock (extend bolt)

1. Press the Schlage button.

To unlock (retract bolt)

1. Find User Code A on the label located on these instructions.
2. Enter User Code A (four digits) into the keypad.

Quick Programming Reference

Adding User Codes

1. Enter the Programming Code (six numbers).
2. Press Enter.
3. Wait for 3 Orange Lights + 3 Beeps.
4. The keypad turns blue.

Deleting User Codes

1. Enter the Programming Code (six numbers).
2. Press Enter.
3. Wait for 3 Orange Lights + 3 Beeps.
4. The keypad turns blue.
5. Enter the new User Code (four numbers).
6. Wait for 3 Orange Lights + 3 Beeps.
7. Enter the unwanted User Code (four numbers).
8. Wait for 3 Orange Lights + 3 Beeps.

Changing the Programming Code

1. Enter the Programming Code (six numbers).
2. Wait for 3 Orange Lights + 3 Beeps.
3. The keypad turns blue.
4. Press Enter.
5. Wait for 3 Orange Lights + 3 Beeps.

FAQ

Q: What should I do if the bolt does not extend or retract after installation?
A: If the bolt does not extend or retract, remove the lock and reinstall it, paying close attention to the cam position in step 3 of the installation instructions.

Q: Where can I find troubleshooting information?
A: For troubleshooting information, visit schlage.com/faqs- keypad.

47327264

Model BE365, BE365F, BE365F20

Visit alle.co/KPD or scan the QR code for a better digital installation experience.

Place Label Here

BE365F, BE365F20

UL cup

BE365F

UL screw

PARTS

IMPORTANT NOTE

• For BE365F and BE365F20, see Additional UL steps (Not common) before beginning. (Not common)
• DO NOT use a power drill for installation!
• Use a screwdriver to remove the product from the packaging.
• Install and test the lock with the door open to avoid being locked out.
• Pay special attention to step 3. If the lock is installed with the cam in the wrong position, the lock will not function properly!

Check door preparation

If the dimensions do not match, you may need to modify your door.

Install the bolt

Adjust the bolt as necessary.

No mortise? See Change faceplate

CAUTION
The bolt must remain retracted throughout the installation

Rotate the baseplate cam to the correct position

Install keypad

Route wire through the hole in the baseplate

INSTALL BASEPLATE

Slides through the same hole as wire. BHolds keypad and baseplate together during installation.

Connect wire and 9V battery

The lock will beep when the battery is connected

Place battery in holder and tuck wires

Any wire routing is acceptable as long as wires will not be pinched by cover

Install cover

Install the strike

The hole must be at least 1 1/4” (32 mm) deep.

Change faceplate

1. Remove faceplate.
2. Remove backplate.
3. Install drive-in faceplate

Additional UL steps (Not common)

BE365F ONLY

Prepare the additional hole

Install UL cup

Install UL plate

Test lock

Lock (extend bolt)

1. Press the Schlage button.
2. Rotate your thumbturn towards the door edge

Did the bolt extend?

• Yes. A lock is installed correctly

• No. A lock is not installed correctly. Remove the lock and reinstall. Pay close attention to the cam position in 3.

For troubleshooting information, go to schlage.com/faqs- keypad.

Unlock (retract bolt)

1. Find User Code A on the label located on these instructions.
2. Enter User Code A (four digits) into the keypad.
3. Rotate your thumb and turn away from the door edge.

Did the bolt retract?

• Yes. The lock is installed correctly.

• No. The lock is not installed correctly. Remove the lock and reinstall. Pay close attention to the cam position in 3.

Quick Programming Reference

Adding User Codes

These four numbers must be different from the first four numbers of the programming code.

Deleting User Codes

Changing the Programming Code

The first four numbers must be different from all of the User Codes currently in the lock.

BEGINNING SHEET

Documents / Resources

| SCHLAGE BE365 Keypad Deadbolt [pdf] Instruction Manual
BE365 Keypad Deadbolt, BE365, Keypad Deadbolt, Deadbolt
---|---

References

• Allegion
• Allegion

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>