ibiza LIGHT LED8-MINI Spider Light User Manual

ibiza LIGHT LED8-MINI Spider Light

IMPORTANT NOTE: Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your dealer about the way to proceed.

Contents of the carton

• 1 x Spider light effect
• 1x Mains lead
• 1x User Manual

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present and have been received in good condition. Notify the freight company immediately and retain packing material for inspection if any parts appear to be damaged from shipping or the carton itself shows signs of mishandling. Keep the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.

Safety Instructions

Please read these instructions carefully, they include important information about the installation, usage and maintenance of this product.

• Please keep this User Guide for future reference. If you sell the unit to another user, be sure that he also receives this instruction booklet.

• Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture.

• This product is intended for indoor use only!
  It is essential that the device is earthed. A qualified person must carry out the electric connection.

• To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are blocked.

• Always disconnect from power source before servicing or replacing fuse and be sure to replace with same fuse size and type.

• Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use its carrying handles.

• Maximum ambient temperature (Ta) is 104° F (40°C). Do not operate the fixture at temperatures higher than this.

• In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type of spare parts.

• Don’t connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.
  DISCONNECT DEVICE: Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

Auto Sensing Voltage: This fixture contains an automatic voltage switch which will auto sense the voltage when it is plugged into the power source.

Specifications

Power supply ……………………………………………………………………………………… 100-240Vac 50/60Hz
Consumption ……………………………………………………………………………………………………………. 39W
Light source …………………………………………………. 8x 3W LED (2x red, 2x green, 2x blue, 2x white)
Single beam angle ………………………………………………………………………………………………………… 4°
Dimensions …………………………………………………………………………………………. 283 x 151 x 110mm
Weight ……………………………………………………………………………………………………………………. 2.5kg

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times the weight of the unit when installing the fixture.

The equipment must be fixed by professionals at a place where is out of the reach of people and where nobody can pass by or under it.

Fuse Replacement
Disconnect the power cord before replacing a fuse and always replace with the same type fuse.

With a flat head screwdriver wedge the fuse holder out of its housing.
Remove the damaged fuse from its holder and replace with exactly the same type of fuse.
Insert the fuse holder back in its place and reconnect power.

Data Cabling
To link fixtures together you must use data cables. If you choose to create your own cable, please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference.

CABLE CONNECTORS
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.

DMX connector configuration

Termination reduces signal errors. To avoid signal transmission problems and interference, it is always advisable to connect a DMX signal terminator.

CAUTION: Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to check correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.

CONTROL PANEL
To access the main menu press the MENU button. Press the UP or DOWN buttons until you reach function you wish to change. When you reach the function you wish to change, press the ENTER button. When a function is selected, use the UP or DOWN buttons to change the function settings.

Once your changes are made, press the ENTER button, and then press and hold the MENU button for at least three seconds to confirm and lock the change into the system memory. To exit without making any adjustments, press the MENU BUTTON. The display will lock after 30 seconds. Press the MENU button for 3 seconds to unlock.

FUNCTION MENU

14 ch, select the channel mode

SLND

| Mast SL 1

SL 2 ( MASTER, SLAVEC OPTION)

SHND| SHOW 0 – SHOW 15, Select the show mode
AUTO| OFF

ON (Auto Mode)

SOUN| On – Off (SOUND CONTROL)
SENS| 000 – 100 Sound sensitivity control (0 close, 100 The most sensitive)
LED| On – Off (Background LIGHT ON/OFF)
DISP| Disp

Dsip (Reverse Display)

PINT| Yes – No (PAN Reverse)
TINT| Yes – No (TIL Reverse)
TEST| Test
RSET| Reset

Settings

DMX Address Setting

1. Press the MENU, UP or DOWN button until “ADDR” is displayed, press ENTER.
2. The current address will now be displayed and flashing. Press the UP or DOWN buttons to find your desired address.
3. Press ENTER to confirm.

DMX channel mode

1. Press the MENU button until “CHND” is displayed, press ENTER. Either “10CH”, “14CH” will be displayed
2. Press the UP or DOWN buttons to find your desired DMX channel mode and press ENTER to confirm and exit.

Show modes 0-15 (Factory programs).
Show mode can run with or without sound active mode active.

1. Press the MENU button until “SHND” is displayed, press ENTER.
2. “Sh X” will now be displayed, “X” representing a number between 0-15. Programs 1-15 are factory programs, while “Sh 0” is random mode. Press the UP or DOWN buttons to find your desired show.
3. When you have found your desired show press ENTER, then press and hold the MENU button for at least 3 seconds to activate. After you have set your desired show, it can be changed at any time using the UP or DOWN buttons.

AUTO program

1. Press the MENU button until “AUTO” is displayed, press ENTER.
2. The Display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” or “OFF”.

Sound Active mode

1. Press the MENU button until “SOUN” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to activate sound active mode, or “OFF” to deactivate sound active mode.
3. Press ENTER, then press and hold the MENU button for at least 3 seconds to activate.

Sound sensitivity

1. Press the MENU button until “SENS” is displayed, press ENTER.
2. A number between 0-100 will be displayed. Press the UP or DOWN buttons to adjust the sound sensitivity. 0 being the least sensitive and 100 being the most sensitive. When you have found your desired setting press ENTER to confirm.

Display back light

1. Press the MENU button until “LED” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to keep the LED display on at all times, or “OFF” to switch to have the LED display switch off after 10 seconds.
3. Press ENTER and then press and hold the MENU button for at least three seconds to confirm.

Display Reverse 180°

1. Press the either the MENU button until “DISP” is displayed, press ENTER.
2. Press the UP button to select “DSIP” to reverse the display, or “DISP” to change the display back.
3. Press ENTER to confirm.

Pan Inversion

1. Press the MENU button until “PINT” is displayed, press ENTER. Either “YES” or “NO” will be displayed.
2. To activate the Tilt inversion press the UP or DOWN buttons until YES is displayed, press ENTER to confirm. To deactivate Tilt inversion, select NO and press Enter.

Tilt Inversion

1. Press the MENU button until “TILT” is displayed, press ENTER. Either “YES” or “NO” will be displayed.
2. To activate the Tilt inversion press the UP or DOWN buttons until YES is displayed, press ENTER to confirm. To deactivate Tilt inversion, select NO and press Enter.

Self test program

1. Press the MENU button until “TEST” is displayed, press ENTER.
2. The fixture will now run a self test. Press MENU to exit.

Reset
Press the MENU button until “Reset” is displayed. Press the ENTER button and the unit will reset itself.

DMX CHANNELS
10 channel definition table

4

| | Strobe
000-007| Close strobe
008-015| Open strobe
016-131| Strobe from slow to fast
132-139| Open strobe
140-181| fast open slow close
182-189| Open strobe
190-231| Slow open fast close
232-239| Open strobe
240-247| Random strobe
248-255| open strobe
5| 0—255| Red dimmer
6| 0—255| Green dimmer
7| 0—255| Blue dimmer
8| 0—255| White dimmer
9| 0—255| Y1, Y2 speed

10

| 000-007| Only others channels can be controlled
008-063| Auto run
064-127| Sound active
128-255| Reset

14 channel definition table

14

| 000-007| Only others channels can be controlled
008-063| Auto run
064-127| Sound active
128-255| Reset

Cleaning

Due to fog residue, smoke, and dust cleaning the internal and external lenses should be carried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-side casing.
2. Clean the external optics with glass cleaner and a soft cloth every 20 days.
3. Always be sure to dry all parts completely before plugging the unit back in.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>