SEELEY TBSI Evaporative Cooler Owner’s Manual
- June 16, 2024
- SEELEY
Table of Contents
TBSI Evaporative Cooler
Product Information
Specifications
-
Model: LCQ / LCS / LCQI / LPQI / BMQ / CPQ TBQ / TBS / TBQI /
TBSI -
Product Type: Evaporative Cooler
-
Website: https://manual-hub.com/
Important Safety Instructions
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
For Europe
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in
a safe way and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
For Australia, New Zealand & Other Non-European
Countries
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard. New hose sets supplied with the appliance
are to be used and old hose-sets should not be re-used.
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY
TO PERSONS, OBSERVE THE FOLLOWING:
-
Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer. -
Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent power
from being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel. -
Never force parts to fit because all parts are designed to fit
together easily without undue force. -
Never drill holes in the cooler’s water reservoir.
Important Notes
This cooler is fitted with a MagIQtouch or MagIQcool Controller.
Please refer to the separate manual provided with the MagIQtouch
Controller for instructions on how to set up and operate this
system. For the MagIQcool Controller, you’ll find details on set-up
and operation in this manual.
Further, it is also a condition of warranty cover that each item
in the Maintenance Schedule in the Owner’s Manual is performed with
the frequency indicated, by a qualified, licensed technician, and
that the Maintenance Schedule is properly filled out (i.e. names,
signature, date, and action taken) when the item is completed.
ANY FAILURE TO CARRY OUT THE REQUIRED MAINTENANCE AND SERVICING
REQUIREMENTS, AND ANY FAILURE TO PROPERLY FILL OUT THE MAINTENANCE
SCHEDULE, WILL VOID YOUR WARRANTY.
Product Usage Instructions
Operating Your Cooler
Please follow the instructions below to operate your cooler:
-
Ensure that the power supply is connected to the cooler.
-
Turn on the power switch of the cooler.
-
Adjust the desired cooling settings using the control panel or
remote control, depending on the model. -
The cooler will start cooling the air and provide a comfortable
environment.
MagIQtouch Controller Operation
To operate the MagIQtouch Controller, please follow these
steps:
-
Refer to the separate manual provided with the MagIQtouch
Controller for initial setup instructions. -
Ensure that the MagIQtouch Controller is properly connected to
the cooler. -
Press the power button on the MagIQtouch Controller to turn on
the cooler. -
Use the touch screen interface to adjust temperature, fan
speed, and other settings. -
Follow the instructions in the MagIQtouch Controller manual for
advanced features and customization options.
MagIQtouch Controller Settings Menu
The MagIQtouch Controller provides various settings for
customization. To access the settings menu, please follow these
steps:
-
Press the menu button on the MagIQtouch Controller.
-
Navigate through the menu options using the touch screen
interface. -
Select the desired setting by tapping on it.
-
Adjust the setting using the provided controls or input
methods. -
Save your changes and exit the settings menu.
FAQ
Can children use this appliance?
This appliance can be used by children aged 8 years and above
under supervision and with proper instructions. Children should not
play with the appliance and should not perform cleaning or
maintenance without adult supervision.
Can I use old hose-sets with this appliance?
No, it is recommended to use the new hose sets supplied with the
appliance. Old hose-sets should not be re-used to ensure safety and
proper functioning.
OWNER’S MANUAL
LCQ / LCS / LCQI / LPQI / BMQ / CPQ TBQ / TBS / TBQI / TBSI
Evaporative Cooler
(English) Original English Instructions
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
FOR EUROPE
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
FOR AUSTRALIA, NEW ZEALAND & OTHER NONEUROPEAN COUNTRIES
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.
—————————————-
i |
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard. New
hose sets supplied with the appliance are to be used and old hose-sets should
not be re-used.
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
a) Use this unit only in the manner intended by the manufacturer. If you have
questions, contact the manufacturer. b) Before servicing or cleaning unit,
switch power off at service panel and lock the service disconnecting means to
prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
Never force parts to fit because all parts are designed to fit together easily
without undue force.
Never drill holes in the cooler’s water reservoir.
IMPORTANT SAFETY INSTRUCTIONS
This cooler is fitted with a MagIQtouch or MagIQcool Controller. Please refer
to the separate manual provided with the MagIQtouch Controller for
instructions on how to set-up and operate this system. For the MagIQcool
Controller, you’ll find details on set-up and operation in this manual.
IMPORTANT NOTES!
In areas where temperatures can cause water supply pipes to freeze, a drain
down facility should be provided during the installation. This drain down
facility must be activated prior to freezing conditions, to avoid possible
damage to the cooler components. Details on how to register your product
warranty can be found near the end of this Owner’s Manual. As with any product
that has moving parts or is subject to wear and tear, it is VERY IMPORTANT
that you maintain the product and have it regularly serviced. It is a
condition of warranty cover for your product that you comply with all of the
maintenance and service requirements set out in the Owner’s Manual. Compliance
with these requirements will prolong the life of your product.
Further, it is also a condition of warranty cover that each item in the
Maintenance Schedule in the Owner’s Manual is performed with the frequency
indicated, by a qualified, licensed technician, and that the Maintenance
Schedule is properly filled out (i.e. names, signature, date, and action
taken) when the item is completed.
ANY FAILURE TO CARRY OUT THE REQUIRED MAINTENANCE AND SERVICING REQUIREMENTS,
AND ANY FAILURE TO PROPERLY FILL OUT THE MAINTENANCE SCHEDULE, WILL VOID YOUR
WARRANTY.
LCQ / LCS / LCQI / LPQI / BMQ / CPQ / TBQ / TBS / TBQI / TBSI OWNER’S MANUAL | ii
TABLE of CONTENTS
OPERATING YOUR COOLER
1
MAGIQTOUCH CONTROLLER OPERATION
1
MAGIQTOUCH CONTROLLER SETTINGS MENU
1
About Appliance
1
Min/Max Set Temperature
1
Night Quiet Mode
1
Manual Drain
1
Pad Flush
1
Autoclean (Breezair® coolers only)
1
MAGIQCOOL CONTROLLER SETTINGS
2
Manual mode
2
Auto mode
2
MAGIQCOOL CONTROLLER OPERATION
2
Turning the Cooler On
2
Preparing to Start
2
Manual Mode
2
Auto Mode
2
Delayed Start or Stop
3
Programming In Manual Mode
3
Programming In Auto Mode
3
Service Mode
3
Drain Mode (Cooler switched OFF)
4
WATER MANAGEMENT
4
WATERMANAGERTM
4
DRAIN VALVE
4
CONTINUOUS BLEED SYSTEM
4
POWER OUTAGES
4
HEALTH REGULATIONS
4
MAINTENANCE
5
Access for Servicing and Maintenance
5
Maintenance Schedule
6
Additional Activities
7
Chillcel Cooling Pad Maintenance
7
Seasonal Maintenance
7
Pre-Season
7
End of Season
7
High Duty Cycle Operation Maintenance
7
Water Distribution Channels
8
LPQI Models
8
Cooler Isolation Switch
8
REMOVING PAD FRAMES
9
Removing Pad Frames – LPQI Models
9
Refitting the Pad Frames – LPQI Models
10
TROUBLESHOOTING
11
HOW TO REGISTER YOUR PRODUCT WARRANTY (Australia only)
12
WARRANTY TERMS AND INFORMATION (Australia only)
13
iii |
Hello and congratulations on purchasing a Seeley
evaporative cooler
At Seeley International we manufacture evaporative coolers from the highest
quality materials, and we have designed the product to provide many years of
economical, troublefree cooling.
OPERATING YOUR COOLER
To provide efficient cooling or ventilation the building must have sufficient
exhaust openings to the outside of the building.
To assist air flow, open windows and doors that are farthest from the outlet
vent in each room. In these rooms, provide an exhaust opening 2 times the vent
size of the room.
Where the design of the building prevents adequate exhaust, consideration
should be given to the provision of mechanical extractions, such as an exhaust
fan.
There are three main ways that an evaporative cooler can operate to provide
cooling comfort.
· The cooler can be set to cool at a constant fan speed, without reference to
the current temperature.
· The cooler can be given a temperature target, in which case it will vary the
fan speed in order to get as close to the target as possible. (Note! Humid
weather conditions may limit the temperatures that can be achieved).
· The cooler can be set to a fan only mode, providing air circulation only.
MAGIQTOUCH CONTROLLER OPERATION
MAGIQTOUCH CONTROLLER SETTINGS MENU
Your MagIQtouch Controller contains a settings menu, which gives you access to
information about your evaporative cooler and to extra functions including:
About Appliance Access information about the appliances installed in your
system.
Min/Max Set Temperature You can change the minimum and maximum temperature
displayed on your slider, depending on what temperature range you prefer your
system to work within.
Night Quiet Mode Restrict fan speed over the night time period for a quiet
night’s sleep.
Manual Drain This will turn the cooler off and drain the tank.
Pad Flush This will turn the cooler off and run the pumps for a specified
time. Use this feature to flush the cooler pads.
Drain And Dry This option allows you to nominate a time each day when the
cooler will drain the tank and run the fan for 1 hour.
Autoclean (Breezair® coolers only) Select the preferred cleaning interval (50
/ 100 / 200 hrs). At 8.00am after the selected running hours has been reached,
the cooler will drain the tank, fill with fresh water and operate the pump for
5 minutes. When complete, drains the tank and returns to previous operation
mode. Note! There are some settings, which are locked and are only for
installers or service technicians.
ILL1582-A
Refer to the Owner’s Manual supplied with the controller for operating
instructions.
LCQ / LCS / LCQI / LPQI / BMQ / CPQ / TBQ / TBS / TBQI / TBSI OWNER’S MANUAL | 1
MAGIQCOOL CONTROLLER SETTINGS
MagIQcool Wall Controllers can operate in manual or automatic mode.
Manual mode
Manual mode will allow you to change settings for operating the cooler, such
as altering fan speeds, pump control and manual drain control.
Auto mode
Auto mode will allow thermostatic control to set temperature targets /
operating settings. It has the capability of programming ON/OFF delay times,
enabling the cooler to automatically start up or shut down after a specified
period of hours.
At all times the MagIQcool Controller will monitor the cooler for faults and
report them to the controller’s screen for your reference.
MAGIQCOOL CONTROLLER OPERATION
Manual Mode
With the wall control switched ON,
press the
button until MAN is shown
on the display.
ILL1122-A
You may then press the
button to
switch between COOL and VENT (where fresh
air is being delivered but not cooled).
ILL2121-A
Turning the Cooler On
The wall control can be switched on and off by
pressing the
button. The wall control
will remember the previous setting it was in
when the cooler was last used.
Preparing to Start
Whenever you select AUTO mode or COOL in MANUAL mode, the cooler will take a few minutes to start as it fills with water and saturates the cooling pads. The time will be decreased if the tank is full or the cooler has only recently been turned OFF.
During this time “Preparing to Start” will flash on the display.
ILL1123-B
Once COOL or VENT has been selected, the wall control will maintain a constant fan speed. This is indicated by the bar graph shown on the display.
To increase or decrease the fan speed
required, press either the
or
button.
Auto Mode
To select the AUTO mode press the button until AUTO is shown on the display.
ILL1124-A
In AUTO mode the cooler will remember the
last setting used. Press the
button if
you require more cool air or the
button
if you require less. Don’t alter the setting
however, until the room temperature has
stabilised.
2 |
MAGIQCOOL CONTROLLER OPERATION cont
Delayed Start or Stop
The cooler can be programmed to start at a specific time or stop at a specific
time.
The delayed start time can only be programmed when the cooler is OFF. To
program the cooler to start in a certain amount of hours use the following
sequence:
Programming In Manual Mode
(1)…… Press the
button.
(2)…… Press the
button until MAN is
displayed on the screen.
(3)…… Press the
or
button
until the desired fan speed is displayed by the
bars in the middle of the screen.
This is ideal if you are going to bed but don’t want to turn the cooler off straight away. To program the delayed time in which you want the cooler to stop use the following sequence:
(1)……Select the
button and the `stops
in’ time will start flashing.
Use the
and
the desired off time.
buttons to select
(2)……Press
again.
ILL1118-A
(4)…… Press the COOL or VENT.
button to set either
(5)…… Press the
button and the `starts
in’ time will start flashing.
Use the
and
the desired time.
buttons to select
(6)…… Press
again.
Programming In Auto Mode
(1)…… Press the
button.
(2)…… Press the displayed.
button until AUTO is
(3)…… Press the
button and the `starts
in’ time will start flashing.
Use the
or
the hour.
button to select
(4)…… Press
again.
ILL1119-B
Service Mode When a fault has been recognised by the wall control the word
“Service” flashes on the screen.
ILL1120-B
When “Service” is displayed it may be necessary for you to phone the service
number located near the back of this manual. However, before doing so, turn
the wall control OFF. You will notice a number flashing at the bottom of the
screen. This number indicates the reason for requiring service.
ILL1117-B
The delayed stop time can only be programmed once the cooler is ON.
ILL1121-B
Please write this number down, then push
the
button to turn the cooler back on.
If after a short time “Service” is again shown
on the display, turn the wall control OFF and
check if the flashing number is the same. If it
is the same check for the following possible
problems.
However, we do recommend that any checks be carried out by an authorised dealer or service agent.
LCQ / LCS / LCQI / LPQI / BMQ / CPQ / TBQ / TBS / TBQI / TBSI OWNER’S MANUAL | 3
MAGIQCOOL CONTROLLER OPERATION cont.
If 02′ is displayed (1)……Check that the water supply tap to the cooler is turned on. (2)……Check that your local water authority haven’t temporarily disconnected the water in your area. If
04′ is displayed
(1)……If your cooler is fitted with a drain valve, check that the drain is not
blocked.
If these do not fix the problem then contact your dealer or the service number
near the back of this manual. You will need to quote the flashing number that
you wrote down.
Drain Mode (Cooler switched OFF)
Pressing the
and
buttons at
the same time for 2 seconds will open the drain
valve and empty the water in the tank. The wall
control will display “dr” on the screen. Draining
the water will leave the tank clean and dry until
it is next used.
WATER MANAGEMENT
Your evaporative cooler will either be fitted with a WaterManagerTM system, or
a continuous bleed system. Check with your dealer to determine which system
has been installed.
WATERMANAGERTM
Seeley evaporative coolers fitted with the WaterManagerTM feature will
automatically monitor the quality of the water in the cooler.
The WaterManagerTM partially drains the existing water in the cooler to allow
it to be replaced with fresh water, when it is needed. Therefore, you may
notice your cooler draining water occasionally. How often the WaterManagerTM
performs this operation depends upon the quality of the water supply and the
rate of evaporation. In areas of poor water quality, the WaterManagerTM will
operate more often as it tries to maintain the optimum water quality in the
cooler. This maximises the cooling effect and life of the cooling pads.
The WaterManagerTM controls salinity either by measuring the salinity levels
in the water (high or low setting), or by performing a timed drain (will drain
the tank after a specified operation time regardless of salinity level).
DRAIN VALVE
The WaterManagerTM system is installed with a drain valve and it is
accompanied by the WaterManagerTM salinity probes. When the tank’s water
salinity level reaches a preset level the WaterManagerTM will open the drain
valve and release saline water. Fresh water will then be added diluting any
minerals or salts accumulated. The WaterManagerTM will continue to monitor and
drain water as required. Alternatively, the cooler can be set to drain saline
water at a preset period of pump operating time.
Note! When the cooler’s tank is empty and the cooler is turned on again, the
fan operation will be delayed as the tank is refilled and the pads are
saturated.
CONTINUOUS BLEED SYSTEM
During operation, the bleed system will drain small amounts of water. This
ensures fresh water is continually added to dilute salt accumulation in the
water caused through evaporation. This helps keep the air cooler in good
condition and ensure optimum performance. The bleed rate will depend on local
operating conditions and will be set by the installer.
POWER OUTAGES
After a power outage the MagIQtouch Controller will prompt you to enter the
date and time. If the AUTO RESTART option is switched on in the SETTINGS menu,
the following actions will result:
If the cooler was last running in MANUAL mode, it will automatically restart
only after the date and time have been confirmed.
If the cooler was last running in PROGRAM mode, it will automatically restart,
even before the time and date have been set, according to the last time
recorded before the power outage.
HEALTH REGULATIONS
In some regions, regulations require that evaporative air coolers be serviced
at specific intervals.
4 |
MAINTENANCE
Maintenance Schedule servicing is essential to ensure the cooler operates
efficiently for many years. It must be carried out by a qualified, licensed
service technician. The following pages outline the suitable maintenance
requirements to ensure that your cooler continues to operate efficiently.
We require that the following components and the operation thereof, be
checked/serviced after the first 6 months of use, then every 2 years for
residential purposes or every year for commercial purposes, as Maintenance
Schedule servicing. Refer to the Maintenance Schedule section.
Maintenance Schedule servicing should be performed before the summer season.
It is important to note that all evaporative coolers have components that may
need periodic replacement (eg. filter pads, hoses, o-rings etc).
Note! Failure to carry out the Maintenance Schedule services will void your
warranty cover.
Note! Maintenance Schedule servicing may be required more frequently in
adverse environmental situations or where the appliance is installed in non-
residential applications. Please consult with the installer or service
personnel to determine if more frequent servicing is required.
WARNING! As your cooler is mounted on the roof, we suggest that any
maintenance or checks be carried out by an authorised Seeley International
dealer or service agent. Climbing onto the roof can be hazardous and could
result in injury to you and damage to your property.
Access for Servicing and Maintenance Working at heights requires additional
safety precautions. Required clearances around the cooler for maintenance and
servicing are shown below.
ILL2645-A
Specific job sites may incur additional charges for servicing in order to
provide safe access to the cooler for servicing, which may include, but not
limited to sites:· with a roof pitch >35° · with limited access to the roof ·
where the roof access point is > 6m
above ground level · where the cooler is located too close to a
fall edge · which are not structurally capable of
supporting the weight of the cooler and service technicians Extra service or
warranty charges may apply for the cost of any equipment or additional labour
involved in providing safe access to the cooler.
LCQ / LCS / LCQI / LPQI / BMQ / CPQ / TBQ / TBS / TBQI / TBSI OWNER’S MANUAL | 5
MAINTENANCE cont. MAINTENANCE SCHEDULE
Service Item
Water Distribution System Chillcel Pads (replace as required) Pad Retaining
Washers/Pins Tank/Water Reservoir Pump Filter Water Probes System Washers,
Seals and O-Rings (replace as required) Drain Valve/Bleed Funnel operation
Component Function Pump operation Drain Valve operation Motor Operation
Solenoid operation Wall Control operation General Operation Water Level Set
Point Water Fill Time Water Drain Time Water Distribution across Pads Airflow
through system/Outlets General Product condition (includes correct fitting of
all components and items – replace as required)
Check/Adjust
Clean
Replace
123451234512345
Service No.
No.1 No.2 No.3 No.4 No.5
Service Date Service Technician
……………………… ……………………………….. ……………………… ………………………………… ………………………. …………………………………
………………………. ………………………………… ………………………. …………………………………
Service Company
…………………………………….. …………………………………….. …………………………………….. ……………………………………..
……………………………………..
6 |
MAINTENANCE cont.
Additional Activities
The maintenance schedule provides a minimum requirement for ensuring your
cooler operates effectively. For best performance from your cooler, additional
cleaning and maintenance tasks may be required depending on its usage. These
are described below.
Chillcel Cooling Pad Maintenance
Efficient cooling and airflow requires clean and un-blocked cooling pads. In
areas with airborne dust, contaminants or debris, or for High Duty cycle
operation, cleaning of the cooling pads is recommended every 3 months.
SEASONAL MAINTENANCE
When used in a residential application, Seasonal Maintenance is only required
if you have a cooler fitted with a constant bleed system. If your cooler is
fitted with a drain valve, no Seasonal Maintenance is required.
Seasonal Maintenance services must be performed at a minimum before and after
the summer season.
Pre-Season
1. Remove the pad frames. 2. Ensure the power is off at the isolating
switch inside the cooler. 3. Gently wash the pad frames to remove any
dust build up during the winter. Note! Do not wash the pads with high pressure
water spray. If pads are salted-up, replace them. 4. Check for water leaks.
Check operation of float valve. 5. Turn on the water supply to the cooler. 6.
Switch on the isolating switch. 7. Refit the pad frames. 8. Run the cooler.
WARNING! Ensure pad frames are fitted when operating the cooler.
End of Season
1. Turn off the water supply to the cooler. 2. Remove the pad frames 3. Turn
off the power at the isolating switch
inside the cooler. 4. Check and clean the water distributing
spreader tray channels under the lid. 5. Drain the tank. 6. Thoroughly clean
the tank, pump filter and
salinity probe (if fitted).
7. If a drain valve is fitted it will automatically drain. If a bleed funnel is fitted, remove it from the tank as shown below. Keep the O-Ring in a safe place for later use.
8. Refit the pad frames.
ILL1141-A
HIGH DUTY CYCLE OPERATION
MAINTENANCE
Only applicable for coolers operating more than 12 hours per day continuously
throughout the year.
The following maintenance program is required in addition to the servicing
required by the Maintenance Schedule:
3 monthly maintenance: · Inspect the cooler and check the pump,
drain valve (if fitted), solenoid and fan motor. · Check the grub screw
securing the fan to the
motor shaft is tight. (LCQI/TBQI/LCSI/TBSI models only) · Check the pads and
replace as required. · Check and clean the tank and the pump filter.
12 monthly maintenance: · Replace plastic fan and motor collet and
check motor shaft for wear. (CPQ/LCQ/LCS/ TBA/TBQ/TBS models only) · Water
distribution channels. · Pump. · Drain valve. · Solenoid and associated filter
/ fittings. · Fan motor operation. · Float valve. · Salinity probes etc
LCQ / LCS / LCQI / LPQI / BMQ / CPQ / TBQ / TBS / TBQI / TBSI OWNER’S MANUAL | 7
MAINTENANCE cont.
CPQ/LCQ/LCS/TBA/TBQ/TBS models
All other models
ILL1897-A
LCQI/LPQI/TBQI/TBSI models
ILL1103-B
Cooler Isolation Switch
Prior to service or maintenance, ensure the mains power to the cooler has been
isolated. There is an additional isolation switch inside the cooler cabinet
that should be switched to “OFF” (refer below).
Grub Screw Location
ILL2939-A
Water Distribution Channels
The spreader section of the water distribution system will need occasional
maintenance and cleaning, depending on the frequency of use, water quality and
associated calcification or solids build-up.
To access the water spreaders, remove the pad frames from the cooler to expose
them.
LPQI Models
ILL1O60-C
8 |
ILL2588-A
REMOVING PAD FRAMES
Insert a flat screw driver tip into the slot as shown and lever until
disengagement occurs.
REMOVING PAD FRAMES LPQI MODELS
At each corner of the cabinet where the padframes overlap there are 2 clips.
These clips will need to be pushed in and disengaged before the pad frames
will pull free.
Important! Be careful not to use excessive force when pushing in the clips so
as not to damage them.
ILL974-B
Take hold of the pad frame and pull it towards you until the internal side
clips disengage.
ILL2587-A
Start by removing the front panel. Once the 4 clips have been disengaged, pull
the top pad frame towards you so that it rotates free from the cabinet. Lift
the pad frame out, taking care not to damage the pad.
ILL975-C
Pivot the pad frame outwards and lift up. Take care not to damage the pad.
ILL2611-A
Next remove the side panels, disengaging the clips holding them to the rear
pad frame.
ILL976-D
ILL2612-A
LCQ / LCS / LCQI / LPQI / BMQ / CPQ / TBQ / TBS / TBQI / TBSI OWNER’S MANUAL |
9
REMOVING PAD FRAMES LPQI MODELS cont.
Finally remove the rear pad frame.
PAD FRAME POSITIONS
All Supercool Chillcel pads for LCS/TBS or TBSI coolers have the side edges
rebated to provide clearance for corner posts. Note the position required for
the pad with the Drain Valve (“B” Rebate) rebate.
ILL2613-A
REFITTING THE PAD FRAMES LPQI MODELS
The pad frames are designed to overlap and interlock and so must be assembled
in a specific order.
Assemble the rear pad frame first by locating the bottom edge inside the lip
of the tank and rotating it forwards. Ensure the retainment lugs along the top
of the padframe are fitted securely into the lid.
ILL2578-A
Once the rear pad frame is assembled, the 2 side pad frames can be fitted in
the same way. Lastly assemble the front pad frame.
Where each of the padframes overlap there are 2 clips. Ensure all the clips
are fully engaged.
ILL2128-A
If fitted incorrectly they may cause problems:
· Thicker pads may catch on internal components causing damage.
· Thicker pads may impede the correct operation of the float valve.
· Incorrect positioning of pads may cause a drop in cooler performance.
· Incorrect fitment may allow water to bypass the pad and be carried over into
the air stream and ducting.
· Water bypass may cause damage to internal electronic components.
10 |
ILL2587-A
TROUBLESHOOTING
Symptom Unpleasant odour
Cause Odour from the new pads
Action
· Use the `Pad Flush’ function in
the SETTINGS menu of your MagIQtouch Controller to flush pads. · Fill tank,
run pump for a short period to wash pads, drain tank, refill and repeat
several times if odour persists. Odour will dissipate after a number of hours
of operation.
Inadequate cooling Cooler turns ON and OFF
Dry pads Dry patches in pads (LPQI Models only)
Insufficient exhaust openings for conditioned air Excessive ambient humidity
Fault in the cooler
Ensure the water supply is turned on. Then check the water flow to the pads.
Check for blockages inside the lid water distribution channels by lifting up
the rubber channel cover. Clear out any debris. Ensure the rubber channel
cover is refitted and pressed down flush all the way around the lid before
refitting pad frames or running the pump.
Ensure sufficient exhaust openings.
On days during the summer when the ambient humidity is high, the cooler will
not reduce the temperature as much as on drier days.
Contact your Seeley International authorised dealer or service number.
If your controller prompts you to call a service agent, please contact your local Seeley International authorised dealer or the service number on the back of this manual.
LCQ / LCS / LCQI / LPQI / BMQ / CPQ / TBQ / TBS / TBQI / TBSI OWNER’S MANUAL | 11
HOW TO REGISTER YOUR PRODUCT WARRANTY (Australia only)
Warranty Information section
HOW TO REGISTER YOUR PRODUCT WARRANTY (Australia only)
Please register your warranty online by visiting seeleyinternational.com and
selecting RESIDENTIAL section on the top right hand side of the screen. Then
follow these steps:
Step 1 Select SUPPORT then REGISTER A PRODUCT FOR WARRANTY
Step 2 Enter your product serial number and “SUBMIT”
Step 3 Enter the required information and “SUBMIT”
Alternatively, go to
https://www.seeleyinternational.com/residential/support/register-a-product-
for-warranty/ which will take you directly to the product warranty
registration page.
Important Note: You need to have the following information to complete your
registration:
· your unit model and size · serial number · date your system was installed ·
name of the dealer you purchased it from
Please complete this section. You will also need to retain your purchase receipt, and proof of any warranty period extension.
Brand:
Model:
Serial No:
Customer Name:
Installation Address:
Installation Type:
Residential / Non Residential / Commercial
Date of installation:
Installer / Dealer:
12 |
WARRANTY TERMS AND INFORMATION (Australia only)
Warranty Details (Australia only) In this warranty: We or us means Seeley
International Pty Ltd (Seeley) ABN 23 054 687 035, and our contact details are
set out at the end of this warranty; You means you, the original end-user
purchaser of the Goods; Supplier means the authorised distributor or retailer
of the Goods that sold you the Goods in Australia; Goods means the product,
unit, appliance or equipment which was accompanied by this warranty and
purchased in Australia; and Relevant Warranty Period means the various
warranty periods as described in clause 1 and clause 3 below, as appropriate.
Our Goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the Goods repaired or replaced if the Goods fail to
be of acceptable quality and the failure does not amount to a major failure.
In addition to any rights and remedies that You may have under the Australian
Consumer Law or any other law, subject to the terms of this warranty, We
provide the following warranty: 1. a. Subject to clause b. below, if during
the first five (5) years from the date of purchase when the Goods are used for
personal, residential household purposes, and for two (2) years for any other
purpose the Goods upon examination prove defective by reason of improper
workmanship or material, We will repair or replace, at our option, the Goods
or any part thereof without charge for either parts or labour, during normal
working hours. b. For Braemar EA Model evaporative coolers, the warranty
periods in clause a. above shall be as follows: · Braemar EA variable/two
speed: the first mentioned period shall also be five (5) years. The second
mentioned period shall also be two (2) years, but only if the Goods are used
for a commercial purpose. · Braemar EA Plug Connect: the warranty period shall
be two (2) years, regardless of whether the Goods are used for personal,
residential household purposes or any other purpose, however the warranty
shall only cover the cost of parts, not labour or any other charge. 2. The
warranty granted under clause 1 applies to all components which form part of
the original evaporative air cooler, but does not cover: a. fair or normal
wear and tear; b. damage, loss or claims caused by, resulting from, or arising
out of any utilities that service or are connected to the Goods, electrical
surges, inadequacies, failure, or other problems in or with any electricity,
power, water, or gas supply to the Goods; c. after the first year: (i) the
replacement, supply, or servicing of consumable items (including without
limitation cooler pads, washers, seals, drive belts) and (ii) maintenance
adjustments to the evaporative air cooler; and d. installation (including
without limitation ductwork, fittings, return air filters and other related
installation components) which is excluded. e. batteries (including damage
caused by leaking or faulty batteries), cracking or breaking of display
screens in controllers, physical damage caused by the user or third parties,
and accidental breakage. 3. Seeley also warrants the structural integrity of
all components made from our exclusive Permatuf polymers for ten (10) years
and your evaporative air cooler cabinet (base, top, corner supports, side
panels, fan and fan housing) against damage caused to it by all forms of
corrosion for twenty five (25) years. 4. During the period to which any
expressed warranty applies, all defective part(s) shall be replaced or
repaired (at the discretion of Seeley) without charge for either parts or
labour, during normal working hours. Should we deem in our absolute discretion
to replace the Goods pursuant to clause 1 or clause 3, we may substitute any
similar good even if it is not on our current price/ equipment list. Further,
Goods presented for repair may be replaced by refurbished goods of the same
type rather than being repaired. Refurbished parts may be used to repair the
Goods.
LCQ / LCS / LCQI / LPQI / BMQ / CPQ / TBQ / TBS / TBQI / TBSI OWNER’S MANUAL |
13
WARRANTY TERMS AND INFORMATION (Australia only) cont.
5. We are under no obligation to repair or replace the Goods or Parts under
clause 1 and 3 above if (i) the Goods have not been installed and commissioned
in accordance with the Installation Manual (ii) the Goods have not been
installed and commissioned properly or competently, (iii) the Goods have not
been operated, serviced and maintained in accordance with the instructions
provided in the Owner’s Manual, or (iv) if any such service or maintenance has
not been properly or competently performed. It is a condition of warranty
cover that each item in the Maintenance Schedule in the Owner’s Manual (if it
was published with such a Schedule) is performed with the frequency indicated,
by a qualified, licensed technician, and that the Maintenance Schedule is
properly filled out (ie names, signature, date, and action taken) when the
item is completed. Any failure to carry out the required maintenance and
servicing requirements, and any failure to properly fill out a Maintenance
Schedule in the Owner’s Manual, will void your warranty. The addition of any
third party device, (except where it is required by the installation
instructions and complies with those instructions), or the removal or
alteration of any Seeley component, or damage due to misuse of the unit, or
faulty installation or commissioning, will void this warranty.
6. As far as the law permits, We will not be liable for any consequential
loss suffered through, or resulting from, the non-operation, or ineffective
operation of the evaporative air cooler. The warranties granted under clause 1
and clause 3 do not cover damage to the evaporative air cooler or other loss
resulting from acts of God.
7. No other person, company or corporation is authorised to offer, or give on
our behalf, any other warranty. The benefits conferred are in favour of You
and any person deriving title to the evaporative air cooler whilst in its
original place of installation. Nothing in this warranty shall be construed as
affecting any rights You may have under all the relevant laws, or Commonwealth
or State Legislation which give You rights which cannot be modified or
excluded by agreement.
8. In order to claim under the warranties granted under clause 1 or clause 3
You must:
a. either:
· contact us within the Relevant Warranty Period on 1300 650 644; or
· log a warranty claim on our website (website address below) within the
Relevant Warranty Period; and
b. make available for inspection by the service agent who will come to the
location of the Goods or send to us at the address below within the Relevant
Warranty Period: (i) the legible and unmodified original proof of purchase,
which clearly indicates the name and address of the original retailer, the
date and place of purchase, the product name or other product serial number,
(ii) all of your records of all service and maintenance carried out to the
Goods, plus the Maintenance Schedule in the Owner’s Manual (if it was
published with such a Schedule), (iii) a copy of the completed Warranty
Information section above, and (iv) if an extended warranty period was
provided by Seeley International for the Goods, then the relevant document
provided by Seeley International confirming that extended warranty period. If
you choose to send the documents described in (i) to (iv) to Seeley
International, then they must be accompanied by a covering letter which states
your name and address and daytime telephone number, the address at which the
Goods are installed, and the model and serial number of the Goods.
9. The warranty granted in clause 1 and clause 3 covers the costs of parts
and labour (note that under clause 1 for Braemar EA Plug Connect models only
parts are covered, not labour) but you will be responsible for:
a. the cost of travel incurred for a Seeley International service agent to get
to and from the location of the Goods if the location of the Goods is either:
(i) outside the metropolitan areas of the capital cities; or (ii) more than 35
kilometres from an authorised Seeley International branch or service
representative; and
b. any costs for additional labour or equipment associated with gaining
acceptable and safe service access to the Goods installed in restricted, high
or unsafe locations, and/ or the removal and replacement of any barrier,
walls, roofs, fences etc; and
c. any costs incurred by the Seeley International service agent in gaining
access to the Goods which is necessary to comply with any safety or workplace
safety requirements and/or any other relevant regulations. For the avoidance
of doubt, the reference to any costs incurred also includes the cost of any
necessary site inductions.
10. Seeley International is not responsible in any way for any failure and/or
inadequate performance of the Goods which arises from or is connected to the
use in the Goods of non-genuine spare parts. Seeley International strongly
recommends that only spare parts supplied or approved by it are used in the
Goods.
11. The employees and Executive of Seeley International are not responsible
for the installation of the Goods and expressly disclaim all liability
resulting from incorrect installations or installations that do not conform to
local electrical codes, local plumbing codes, Occupational Health and Safety
requirements, and by laws which are legislated or in effect at the time of
installation.
14 |
WARRANTY TERMS AND INFORMATION (Australia only) cont.
12. This warranty is only valid and enforceable in Australia. Note: Seeley
and its service agents reserve the right to refuse service unless safety and
accessibility to the unit can be guaranteed. If a service call reveals no
warranty fault found with the Goods, a charge will be made for the call. Our
liability under this warranty is limited to the extent permitted by law. That
is, to the extent that it is fair and reasonable, if the Goods are not of a
kind ordinarily acquired for personal, domestic or household use or
consumption, your remedies associated with any failure or defect of the
Product will be limited to:
a. the replacement of the Goods or the supply of equivalent goods; b. the
repair of the Goods; c. the payment of the cost of replacing the Goods or of
acquiring equivalent goods; or d. the payment of the cost of having the Goods
repaired and subject to the terms and conditions included in this warranty.
Service Department Seeley International Pty Ltd 112 O’Sullivan Beach Road
Lonsdale, South Australia 5160 Customer service centre 1300 650 644 Website:
www.seeleyinternational.com
FOR SERVICE Service call Booking To book a Service on your Seeley
International product Online visit www.seeleyinternational.com Step 1 Select
“SUPPORT” and “BOOK A SERVICE”. Step 2 On the “FIND A SERVICE AGENT” page,
enter your POSTCODE and select a category (for example “EVAPORATIVE”), select
the “SEARCH” button. Step 3 On the “RESULTS” page, select the “BRAND” of your
cooler. Step 4 Choose “SELECT” for your preferred agent from the list
provided. Step 5 Select “BOOK A SERVICE”. or Phone 1300 650 644 to be directed
to your closest authorised Service Agent.
PRIVACY NOTICE Seeley International Pty Ltd ABN 23 054 687 035 will use the
personal information you provide us with to provide warranty support for the
product you have purchased and to inform you about other products and
services. If you choose not to supply us with the information requested, we
may be unable to provide you with warranty support. We may also disclose your
information to third parties, such as related entities; retailers,
distributors, service agents and contractors who are affiliated with us; or
marketing or market research companies. If you would prefer not to receive
direct marketing communications from us, please follow the instructions to
“unsubscribe” which will be included in the direct marketing communications we
send you, or contact our Privacy Officer using the details set out below.
While we do not currently transfer personal information to overseas recipients
or store personal information overseas, if we transfer your information to
third parties who do so, we will take reasonable steps to ensure that the
overseas recipients do not breach the Australian Privacy Principles. By
registering your warranty, you consent to having your personal information
used in this way. Please read our Privacy Policy on our website
www.seeleyinternational.com for further explanation of how we collect, use,
hold and disclose personal information, and how you may access and seek
correction of your information. It also sets out how you may complain about a
breach of the Australian Privacy Principles, and how we will deal with your
complaint. You may contact us at: Privacy Officer, Seeley International Pty
Ltd, 112 O’Sullivan Beach Road, Lonsdale, South Australia 5160.
LCQ / LCS / LCQI / LPQI / BMQ / CPQ / TBQ / TBS / TBQI / TBSI OWNER’S MANUAL |
15
When your product requires servicing, please quote the cooler serial and model
number
Affix serial & model number sticker here
Warranty (Australia only) To register your warranty, go to
www.seeleyinternational.com/register-warranty
Service For Australia contact 1-300-650-644 For outside Australia contact your
local dealer
seeleyinternational.com
MANUFACTURED BY: SEELEY INTERNATIONAL PTY LTD 112 O’SULLIVAN BEACH RD,
LONSDALE SA, 5160. AUSTRALIA
IMPORTED BY: SEELEY INTERNATIONAL (EUROPE) LTD UNIT 11 BYRON BUSINESS CENTRE
DUKE STREET,
HUCKNALL NOTTINGHAM, NG15 7HP UNITED KINGDOM
SEELEY INTERNATIONAL (AMERICAS) LTD 1002 S 56TH AVENUE, SUITE # 101 PHOENIX,
ARIZONA 85043, USA
SEELEY INTERNATIONAL (AFRICA) PTY LTD 6 WITTON ROAD, FOUNDERSVIEW SOUTH,
MODDERFONTEIN 1609, GAUTENG, SOUTH AFRICA
It is the policy of Seeley International to introduce continual product
improvement. Accordingly, specifications are subject to change without notice.
Please consult with your dealer to confirm the specifications of the model
selected.
865200-C
seeleyinternational.com
AU EU US 1902
References
- Manual-Hub.com - Free PDF manuals!
- Seeley International - World Leading Air Conditioners
- Seeley International - World Leading Air Conditioners
- Register a Product for Warranty - Seeley International
- Manual-Hub.com – Free PDF manuals!
- Register a Product for Warranty - Seeley International
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>