SEELEY CPH01B Convection Panel Heater Owner’s Manual
- June 13, 2024
- SEELEY
Table of Contents
OWNER’S MANUAL
Prestigio Convection Panel Heater
CPH01B, CPH02B
CPH01M, CPH02M
CPH01W, CPH02W
(CPH01/2B/M/W)
SAFETY
General Safety
Please read these instructions before using the fan and keep for future
reference.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction in using the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
Do not poke anything through the ventilating slits.
Always use the heater in an upright position. Stand it on a firm, solid,
horizontal base (not on thick pile carpets).
WARNING: In order to avoid overheating, do not cover the heater.
Leave nothing hanging above or in front of the heater (e.g. clothes, curtains,
bedding, fabrics). Be sure that the back panel vent slots on the heater are
uncovered otherwise it will overheat.
Clean these openings at regular intervals to prevent airflow reduction (refer
Maintenance section).
The heater surfaces are hot when in use. To avoid burns, keep bare skin away
from the top ventilation outlets.
Leave plenty of room around the heater.
Do not use this heater outdoors, or on wet surfaces. Do not use the heater
near flammable areas or substances.
Electrical Safety
Connect the heater to a single 230 V, 10A socket only. Do not plug into double
adaptors or multi-outlet power boards.
Make sure that the heater never comes into contact with water.
Never position the heater under a power outlet.
Never turn the heater on if the lead is damaged or if the heater’s casing is
obviously damaged. If the power supply cord is damaged it must be replaced by
the manufacturer, a service agent or similarly qualified persons in order to
avoid a hazard.
Do not pull the heater along by the power cord or place the cord near the
heaters surfaces. Always uncoil the power cord completely before use. Use of
extension cords is not recommended.
Do not use this heater in the immediate surroundings of a bath, a shower or a
swimming pool. If the heater is to be used in a bathroom, ensure that switches
and other controls cannot be touched by a person in the bath or shower.
Do not use the heater with a separate timer to turn the heater on. Always turn
the heater off and unplug from the power socket when not in use.
Safety Device
To avoid overheating problems the inbuilt safety device will interrupt
electricity if the heating element becomes too hot.
The heater will then return to stand-by mode.
If this should happen:
- Check that the heater is positioned correctly, not close to any furnishings.
- See that there is no dust or other obstacles blocking the vent slots.
- Clean the vent slots if necessary.
The heater is also equipped with a ‘tipover’ switch, which will turn off power to the heater elements if it should fall over.
ASSEMBLY
Component List
A Front Panel
B Control Panel
C Display Panel
D Power Switch
E Rating Plate
F Leg Support (x 2)
G Back Panel
H Wall Mounting Bracket
I Power Cord
J Remote Control
Assembly Instructions
Unpack the heater and make sure it is undamaged and all components are
present.
Your heater must be assembled for either the Portable or Wall Mounting option
before use, and not be free standing.
Portable Assembly:
Turn the heater upside down and assemble the two leg supports by unscrewing
and then refixing with the wing-nut as shown (Fig. 1-3). Ensure both wing-nuts
are tightened firmly and the castors are secure before using the heater.
Note: the longer leg section is at the rear of the heater as
shown.
Wall Mounting Assembly
NOTE: the wall mounting bracket supplied with the heater must be used.
Because wall types differ, mounting hardware (screws and wall anchors) are not
supplied and will need to be purchased from your local hardware retailer.
Please use the following fixed weights as a guide:-
Model CPH01B/W/M: 9.3 kg
Model CPH02B/W/M: 12.6 kg
There are 4 fixing points that must be used.
The heater must be positioned so it complies with the minimum clearances shown
in Fig 4. Loosen the 2 screws from the top of the mounting bracket (refer Fig
5), then push down on the top and bottom tabs to release the mounting bracket
from the rear panel Fix the wall bracket securely to the wall through the 4
screw holes provided (Fig 6). Raise the heater onto the bracket, engaging the
2 bottom tabs of the wall bracket first. Ensure the bottom tabs slide up into
the heater rear panel and lock into place (Fig 7). Push the heater back onto
the 2 top wall bracket tabs, ensuring they ‘click’ into the rear panel slots
(Fig 8). Tighten the 2 screws to lock the bracket into place. Remote Control
Setup
- Remove the battery protector tab (Fig 9).
- When the heater’s power is on, the remote control can be used to operate the heater from up to 6m away.
Note: if there are two or more heaters within this distance, both will be operated by the same remote control.
OPERATION
Heater operation
- Activate the heater for use by pressing the “ON/OFF” remote isolate button on the unit (see Fig 9). The heater will ‘beep’ and the room temperature will be displayed on the LED display.
- Turn the heater ON by pressing the “ON/OFF” button on the unit or the remote control. Press the “MODE” button on the unit or the remote control to change the heat setting from LO (1000W heating) to HI (2000W).
- Turn the heater OFF by pressing the “ON/OFF” button at any time.
To use the THERMOSTAT:-
Your heater will operate most efficiently when utilising the thermostat to
turn your heater off when your desired heat setting is reached. To operate
your thermostat:
-
Press the “MODE” button on the unit or remote control to select “AUTO” setting.
-
Select the temperature setting you want by pressing the “TEMP” button on the unit or remote. You can select in the range of 5°-35°C.
-
When the room temperature is below the selected set temperature, the unit will heat the room. If the room is above the set temperature, the heat element will turn off.
Do not set the thermostat temperature too high. This will consume more power. 23°C is the recommended set temperature.
Tip !
To use the TIMER function:-
The TIMER function can be used to turn the heater OFF automatically. -
Press the “TIMER” button on the unit or remote control – “0.0” and symbol will appear on the display.
-
Continually press the “TIMER” button to adjust the set time by 0.5 hr increments up to 8 hrs. You can change the time remaining at any point by repeating the above steps.
-
Leave at the desired time. The timer will begin to count down until the heater turns itself off.
-
To cancel the timer, set the time to “0.0”.
The symbol will no longer be lit.
MAINTENANCE
To maximise the efficiency of the heater, clean the inlet and outlet grilles regularly.
- Unplug the heater from the mains power supply before cleaning.
- Use a soft, damp cloth to wipe the outside. Never use thinners or other strong chemicals on the heater surfaces.
- Use a vacuum cleaner to remove dirt and dust from the back panel vent slots.
- Ensure the heater is dry before plugging back into the mains power supply.
WARRANTY
In this warranty:
We us or means Seeley International Pty Ltd ABN 23 054 687 035, and our
contact
You details are set out at the end of this warranty;
Supplier means you, the original end-user purchaser of the Goods;
Goods means the authorised distributor or retailer of the Goods that sold you
the in Australia; and means the product, unit, appliance or equipment which
was accompanied
Goods by this warranty and purchased in Australia.
Our Goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the Goods repaired or replaced if the Goods fail to
be of acceptable quality and the failure does not amount to a major failure.
In addition to any rights and remedies that You may have under the Australian
Consumer Law or any other law, subject to the terms of this warranty, We
provide the following warranty:
-
If, during the first 24 months from the date of first retail purchase ( Warranty Period), the Goods upon examination prove defective by reason of improper workmanship or material, We will replace the Goods or any part thereof without charge. We may substitute any similar good even if it is not on our current price/equipment list.
-
We are under no obligation to replace the Goods under clause 1 if the Goods have not been used only for personal, domestic or household purposes and have not been installed/mounted (if relevant), operated, and maintained in accordance with the instructions in the Owner’s Manual. The addition of any third party device or the removal or the alteration of any of our components will void this warranty. In addition, the warranty granted under clause 1 does not apply to:
• Adjustments necessary due to misuse of the appliance,
• Normal user maintenance,
• Setting of controls,
• Transit damage, or
• Damage caused by user misuse, tampering, or failure to observe the care and special provisions in the instructions. -
The warranty granted under clause 1 is limited to replacement only. As far as the law permits, We will not be liable for any consequential loss suffered through, or resulting from, the non operation, or ineffective operation of the Goods. The warranty granted under clause 1 does not cover damage to the Goods or other loss resulting from acts of God.
-
No other person, firm or corporation is authorised by us to offer or give on our behalf any other or greater warranty than that given under this warranty. The benefits conferred by this warranty are in favour of You and any person deriving title to the goods through or under such person and are intended to be separate from and additional to all other rights and remedies that they may have in law in respect of the goods.
-
We are not responsible in any way for any failure and/or inadequate performance of the Goods which arises from or is connected to the use in the Goods of nongenuine spare parts. We strongly recommend that only spare parts supplied or approved by us are used in the Goods.
-
In order to claim under the warranty granted under clause 1 You must within the Warranty Period return the Goods to the Supplier at the place of purchase together with the proof of purchase.
-
Alternatively, you may claim under the warranty granted under clause 1 by within the Warranty Period returning the Goods to us at the address below together with: (i) a covering letter which states your name and address, daytime telephone number, and model and serial number of the goods, (ii) the legible and unmodified proof of purchase, which clearly indicates the name and address of the original retailer, the date and place of purchase, and the product name or other product serial number, and (iii) a copy of the completed Warranty Information below.
-
This warranty does not cover the cost of claiming under the warranty, it is your responsibility to cover all forwarding and freight costs incurred in returning the Goods to the Supplier at the place of purchase or us.
-
This warranty is only valid and enforceable in Australia.
Our liability under this warranty is limited to the extent permitted by law. That is, to the extent that it is fair and reasonable, if the Goods are not of a kind ordinarily acquired for personal, domestic or household use or consumption, your remedies associated with any failure or defect of the Product will be limited to:
(a) the replacement of the Goods or the supply of equivalent goods;
(b) the repair of the Goods;
(c) the payment of the cost of replacing the Goods or of acquiring equivalent goods; or
(d) the payment of the cost of having the Goods repaired and subject to the terms and conditions included in this warranty.
For technical assistance before returning the product please contact:
1300 650 399
Please retain your receipt as proof of purchase. Every request for warranty
must be accompanied by proof of purchase.
Complete the following for your records:
Serial Number:
Product| Convair Prestigio
Model| CPH01B CPH01W CPH01M
CPH02B CPH02W CPH02M
Purchased from| ………………………………………………………….
Date purchased| ……/……/……
You can also register your warranty with us on our website.
Service Department
Seeley International Pty Ltd
112 O’Sullivan Beach Road
Lonsdale, South Australia 5160
Technical assistance in Australia: 1300 650 399
Website: www.seeleyinternational.com
**** Waste electrical products must not be disposed of with household waste.
This product should be taken to your local recycling centre for safe
treatment.
As the policy of this company is one of continuous improvement, all
specifications are subject to change without notice.
It is the policy of Seeley International to introduce continual product
improvement. Accordingly, specifications are subject to change without notice.
Please consult with your dealer to confirm the specifications of the model
selected.
Warranty Service
Australia 1-300-650-399
seeleyinternational.com AU 1111
convair.net.au
00144901-B
References
- Welcome to Convair Air Conditioning - Convair Air Conditioning
- Seeley International - World Leading Air Conditioners
- Seeley International - World Leading Air Conditioners
- Manual-Hub.com – Free PDF manuals!